RR4-S06-D06 - RSG Electronic Components GmbH

RR4-S06/D06
6 Watt 2:1 regulated
single & dual output
DIP24, wide 2:1 input range
Full SMD technology
■ 1500 VDC isolation up to 3500 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 83%
■ -40°C~85°C operation temperature range
■ Optional plastic case
■
■
OUTPUT SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS (4)
Voltage accuracy
Line regulation
Load regulation
± 1%
± 0.5%
± 0.5%
(Output 3.3 V Model)
± 1.5%
Ripple & Noise (20 MHz bandwith) (1)
60 mV pk-pk
Short circuit protection
Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
12 modes
-0.7 ~ 24 VDC
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature
260°C
INPUT SPECIFICATIONS
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
PI Type
35 mA pk-pk
(1.5 mm from case 10 sec.)
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1500 ~ 3500 VDC
Metal case / input & output
1000 VDC
I/O isolation capacitance
470 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
typ. 266 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1:2001
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
PHYSICAL SPECIFICATIONS
Case material
Base material
Pin material
Potting material
Weight
Dimensions
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Non-conductive black plastic
(UL94V-0 rated)
Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
Metal 17 g, plastic 13.5 g
1.25“ x 0.8“ x 0.4“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
-40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
Page: 1/3
Last update: 12.02.09
RR4-S06/D06
6 Watt 2:1 regulated
single & dual output
NUMBER STRUCTURE
RR4
-
XX
XX
DERATING CURVE
S
Name/Package
RR4=DIL24
Input
12=9~18V
24=18~36V
48=36~72V
06
Power
06=6W
Output
03=3.3V
05=5V
09=9V
12=12V
15=15V
24=24V
1
A
Code
internal
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
3=3.5 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RR4-1203S06AX
RR4-1205S06AX
RR4-1209S06AX
RR4-1212S06AX
RR4-1215S06AX
RR4-1224S06AX
RR4-1203D06AX
RR4-1205D06AX
RR4-1209D06AX
RR4-1212D06AX
RR4-1215D06AX
RR4-1224D06AX
RR4-2403S06AX
RR4-2405S06AX
RR4-2409S06AX
RR4-2412S06AX
RR4-2415S06AX
RR4-2424S06AX
RR4-2403D06AX
RR4-2405D06AX
RR4-2409D06AX
RR4-2412D06AX
RR4-2415D06AX
RR4-2424D06AX
RR4-4803S06AX
RR4-4805S06AX
RR4-4809S06AX
RR4-4812S06AX
RR4-4815S06AX
RR4-4824S06AX
RR4-4803D06AX
RR4-4805D06AX
RR4-4809D06AX
RR4-4812D06AX
RR4-4815D06AX
RR4-4824D06AX
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
30 / 527
30 / 649
30 / 641
30 / 617
30 / 625
30 / 625
30 / 527
30 / 649
30 / 625
30 / 625
30 / 632
30 / 625
20 / 256
20 / 313
20 / 304
20 / 313
20 / 304
20 / 305
20 / 333
20 / 321
20 / 301
20 / 312
20 / 312
20 / 312
12 / 128
12 / 156
12 / 152
12 / 156
12 / 151
12 / 151
12 / 171
12 / 158
12 / 158
12 / 156
12 / 156
12 / 156
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
1400
1200
666
500
400
250
±909
±600
±333
±250
±200
±125
1400
1200
666
500
400
250
±909
±600
±333
±250
±200
±125
1400
1200
666
500
400
250
±909
±600
±333
±250
±200
±125
73
77
78
81
80
80
73
77
80
80
79
80
75
80
82
80
82
82
75
78
83
80
80
80
75
80
82
80
83
83
73
79
79
80
80
80
1000
1000
680
330
220
68
±680
±330
±220
±100
±47
±33
1000
1000
680
330
220
68
±680
±330
±220
±100
±47
±33
1000
1000
680
330
220
68
±680
±330
±220
±100
±47
±33
Page: 2/3
Last update: 12.02.09
RR4-S06/D06
6 Watt 2:1 regulated
single & dual output
EFFICIENCY VS OUTPUT CURRENT 12
EFFICIENCY VS OUTPUT CURRENT 24
Efficiency (%)
24 MODELS
Efficiency (%)
12 MODELS
Load
Load
EFFICIENCY VS OUTPUT CURRENT 48
PIN CONNECTIONS
Copper and Plastic models / High isolation same as normal
Pin Number
Single
Dual
48 MODELS
Efficiency (%)
2
3
9
11
14
16
22
23
-V Input
-V Input
N.P.
N.C.
+V Output
-V Output
+V Input
+V Input
-V Input
-V Input
Common
-V Output
+V Output
Common
+V Input
+V Input
Load
MECHANICAL SPECIFICATIONS COPPER
MECHANICAL SPECIFICATIONS PLASTIC
RSG
RR4-XXXXX06AX
24 Pin DIL package
Nickel coated copper
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
24 Pin DIL package
Non-conductive Plastic
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 3/3
Last update: 16.01.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de