RR2-S04-D04 - RSG Electronic Components GmbH

RR2-S04/D04
4 Watt regulated
single & dual output
DIP24, wide 2:1 input range
Full SMD technology
■ 1500 VDC isolation up to 3500 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 82%
■ -25°C~85°C operation temperature range
■ Optional metal case
■
■
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation
Ripple & Noise (20 MHz bandwith) (1)
Short circuit protection
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 1%
± 0.5%
± 0.5%
60 mV pk-pk
Continuous
± 0.02%/°C
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
12 modes
-0.7 ~ 24 VDC
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature
260°C
(1.5 mm from case 10 sec.)
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
PI Type
35 mA pk-pk
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / Output
1500 ~ 3500 VDC
Metal case / input & output
1000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
100~400 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 2.199 Mhrs.
Safety standard (designed to meet)
IEC 60950-1:2001
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
6) It´s necessary to add a minimum capacitor in output for
some models. Please check single model datasheet for
detail value.
PHYSICAL SPECIFICATIONS
Case material
Base material
Pin material
Potting material
Weight
Dimensions
Non-conductive black plastic
(UL94V-0 rated)
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
Plastic 12.5 g, Metal 15 g
1.25“ x 0.8“ x 0.4“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
-25°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
Page: 1/3
Last update: 06.02.09
RR2-S04/D04
4 Watt regulated
single & dual output
NUMBER STRUCTURE
RR2
-
XX
XX
Output
05=5V
09=9V
Input
12=12V
12=9~18V 15=15V
24=18~36V 24=24V
48=36~72V
DERATING CURVE
S
Name/Package
RR2=DIL24
04
Power
04=4W
A
1 (M)
Code
internal
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
3=3.5 kVDC
Add suffix „M“ for Metal case! If no suffix mean Plastic case.
MODEL SELECTION GUIDE
Model Number
RR2-1205S04AX
RR2-1209S04AX
RR2-1212S04AX
RR2-1215S04AX
RR2-1224S04AX
RR2-1205D04AX
RR2-1209D04AX
RR2-1212D04AX
RR2-1215D04AX
RR2-1224D04AX
RR2-2405S04AX
RR2-2409S04AX
RR2-2412S04AX
RR2-2415S04AX
RR2-2424S04AX
RR2-2405D04AX
RR2-2409D04AX
RR2-2412D04AX
RR2-2415D04AX
RR2-2424D04AX
RR2-4805S04AX
RR2-4809S04AX
RR2-4812S04AX
RR2-4815S04AX
RR2-4824S04AX
RR2-4805D04AX
RR2-4809D04AX
RR2-4812D04AX
RR2-4815D04AX
RR2-4824D04AX
Input
Range
VDC
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
Input current (mA)
No Load/Full Load
Output Output current Output current Efficiency Capacitor
VDC
Min. Load (mA) Full Load (mA) @FL (%) Load (HF)
20 / 432
20 / 416
20 / 416
20 / 416
20 / 416
20 / 432
20 / 416
20 / 416
20 / 416
20 / 416
12 / 210
12 / 203
12 / 203
12 / 203
12 / 203
12 / 210
12 / 203
12 / 203
12 / 203
12 / 203
8 / 106
8 / 101
8 / 101
8 / 101
8 / 101
8 / 109
8 / 101
8 / 101
8 / 101
8 / 101
5
9
12
15
24
±5
±9
±12
±15
±24
5
9
12
15
24
±5
±9
±12
±15
±24
5
9
12
15
24
±5
±9
±12
±15
±24
200
111
83.3
66.8
41.8
±100
±55.5
±41.8
±33.3
±20.8
200
111
83.3
66.8
41.8
±100
±55.5
±41.8
±33.3
±20.8
200
111
83.3
66.8
41.8
±100
±55.5
±41.8
±33.3
±20.8
800
444
333
267
167
±400
±222
±167
±133
±83
800
444
333
267
167
±400
±222
±167
±133
±83
800
444
333
267
167
±400
±222
±167
±133
±83
77
80
80
80
80
77
80
80
80
80
79
82
82
82
82
79
82
82
82
82
78
82
82
82
82
76
82
82
82
82
2200
470
470
470
220
±1000
±220
±220
±220
±100
2200
470
470
470
220
±1000
±220
±220
±220
±100
2200
470
470
470
220
±1000
±220
±220
±220
±100
Page: 2/3
Last update: 06.02.09
RR2-S04/D04
4 Watt regulated
single & dual output
MECHANICAL SPECIFICATIONS FOR HIGH ISOLATION MODELS
RSG
■
RR2-XXXXX04AX
24 Pin DIL package
Non-Conductive Plastic
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
MECHANICAL SPECIFICATIONS METAL CASE
RSG
■
RR2-XXXXX04AXM
24 Pin DIL package
Nickel Coated Copper
„M“ Case
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 3/3
Last update: 06.02.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de