RV2-S10-D10 - RSG Electronic Components GmbH

RV2-S10/D10
10 Watt regulated
single & dual output
2"x1" package, wide 4:1 input range
Full SMD technology
■ 1500 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 85%
■ -40°C~85°C operation temperature range
■ EMI complies with EN55022 class A
■
■
OUTPUT SPECIFICATIONS
ENVIRONMENT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation (From 10% to 100% Load)
Operating temperature
Maximum case temperature
Storage temperature
Cooling
± 1%
± 0.5%
± 0.5%
(below 10% load)
± 1.0%
Cross regulation (Dual output) (1)
± 5.0%
Ripple & Noise (20 MHz bandwith) (2)
75 mV pk-pk
Over current protection (of max. Io)
140%
Short circuit protection
Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (3)
See table
INPUT SPECIFICATIONS
Voltage range
Start up time (nom. Vin and constant resistive load)
Max. input current
No-load input current
Input filter
Input reflected ripple current (4)
See table
20ms typ
See table
See table
PI type
35 mA pk-pk
-40°C~ 85°C (See derating curve)
100°C
-40°C~125°C
Nature convection
ABSOLUTE MAXIMUM RATINGS (6)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature
260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1500 VDC
Metal case / input & output
1000 VDC
I/O isolation capacitance
1200 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
typ. 300 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1:2001
Remote on/off (optional)
On: 2.5~5.5VDC or open cicuit
Off: -0.7~0.8VDC or short circuit
(idle current: 2.5mA typ.)
pin 2 and pin 6
NOTE
1) One load is 25% to 100%, the other load is 100%. The
output voltage variable rate is within ±5%.
2) Ripple / Noise measured with 20 MHz bandwith.
3) Tested by minimal Vin and constant resistive load.
4) Measured input reflected ripple current with a simulated
source inductance of 12uH.
5) Input filter components (C1, C2, L) are used to help
meeting the conducted emissions requirements for the
module. These components should be mounted as close as
possible to the module and all leads should b minimized to
decrease radiated noise.
6) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
EMC CHARACTERISTICS
Radiated emissions
Conducted emissions
ESD
RS
EFT
CS
PFMF
(5)
EN55022
EN55022
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-6
EN61000-4-8
Class A
Class A
Perf. crit. B
Perf. crit. A
Perf. crit. B
Perf. crit. A
Perf. crit. A
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
Nickel-coated brass
Ø 1.0 mm brass solder-coated
Epoxy (UL94V-0 rated)
30 g
2“ x 1“ x 0.4“
Page: 1/3
Last update: 12.02.09
RV2-S10/D10
10 Watt regulated
single & dual output
NUMBER STRUCTURE
RV2 - XX
XX
Output
03=3.3V
05=5V
Input
07=7.2V
24=9-36V 09=9V
48=18-72V 12=12V
15=15V
DERATING CURVE
S
Name/Package
RV2=2“x1“
10
Power
10=10W
A
1 *C
Code
internal
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
*C = Control function (optional)
Please add suffix „C“ for Control function
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RV2-2403S10A1
RV2-2405S10A1
RV2-2407S10A1
RV2-2409S10A1
RV2-2412S10A1
RV2-2415S10A1
RV2-2405D10A1
RV2-2407D10A1
RV2-2409D10A1
RV2-2412D10A1
RV2-2415D10A1
RV2-4803S10A1
RV2-4805S10A1
RV2-4807S10A1
RV2-4809S10A1
RV2-4812S10A1
RV2-4815S10A1
RV2-4805D10A1
RV2-4807D10A1
RV2-4809D10A1
RV2-4812D10A1
RV2-4815D10A1
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
25 / 348
25 / 508
25 / 502
25 / 502
25 / 490
25 / 490
25 / 508
25 / 502
25 / 502
25 / 490
25 / 490
20 / 174
20 / 254
20 / 251
20 / 251
20 / 245
20 / 245
20 / 254
20 / 251
20 / 251
20 / 245
20 / 245
3.3
5
7.2
9
12
15
±5
±7.2
±9
±12
±15
3.3
5
7.2
9
12
15
±5
±7.2
±9
±12
±15
2000
2000
1388
1111
833
666
±1000
±694
±555
±416
±333
2000
2000
1388
1111
833
666
±1000
±694
±555
±416
±333
80
82
83
83
85
85
82
83
83
85
85
79
82
83
83
85
85
82
83
83
85
85
3300
3300
1000
680
680
470
±2200
±470
±470
±470
±330
3300
3300
1000
680
680
470
±2200
±470
±470
±470
±330
Page: 2/3
Last update: 12.02.09
RV2-S10/D10
10 Watt regulated
single & dual output
EFFICIENCY VS OUTPUT CURRENT
EFFICIENCY VS OUTPUT CURRENT
Efficiency (%)
48 MODELS
Efficiency (%)
24 MODELS
Load
Load
PIN CONNECTIONS STANDARD
PIN CONNECTIONS REMOTE CONTROL (optional)
Pin Number
Single
Dual
Pin Number
Single
Dual
1
2
3
4
5
6
+V Input
-V Input
+V Output
N.P.
-V Output
N.P.
+V Input
-V Input
+V Output
Common
-V Output
N.P.
1
2
3
4
5
6
+V Input
-V Input
+V Output
N.P.
-V Output
CTRL
+V Input
-V Input
+V Output
Common
-V Output
CTRL
DIMENSIONS
MECHANICAL SPECIFICATIONS
RSG
■
RV2-XXXXX10A1
Notes:
All dimensions are typical
in millimeters (inches).
1) Pin diameter: 1.0 ± 0.05 (0.04 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 3/3
Last update: 12.02.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de