RD1-D10 - RSG Electronic Components GmbH

RD1-D10
1.0 Watt unregulated
dual output
8 Pin DIP8 package
1000 VDC isolation up to 3000 VDC isolation
■ Low ripple and noise
■ Efficiency up to 80%
■ -40°C~85°C operation temperature range
■ Non-conductive black plastic case
■ EMI complies with EN55022 class B
■
■
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation (Per 1% Vin Charge)
Load regulation (From 20% to 100% Load)
(Output 3.3 V Model)
Ripple & Noise (20 MHz bandwith) (1)
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 3%
± 1.2%
± 10%
± 20%
100 mV pk-pk
± 0.02%/°C
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
0 ~ 7 VDC
12 modes
0 ~ 15 VDC
24 modes
0 ~ 28 VDC
Lead soldering temperature
INPUT SPECIFICATIONS
260°C
(1.5 mm from case 10 sec.)
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
± 10%
See table
See table
Capacitors
20 mA pk-pk
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed to
be correct at time of publication. However, we accept no responsibility for
consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1000 ~ 3000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
variable 80 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
EMC SPECIFICATIONS
Radiated emmisions
ESD
RS
EN55022
FCC 47 CFR
Part 15 Subpart B
IEC 61000-4-2
IEC 61000-4-3
Class B
Class B
Perf. criteria B
Perf. criteria A
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
Non-conductive black plastic
(UL94V-0 rated)
Ø 0.5 mm br. solder-coated
Epoxy (UL94V-0 rated)
1.8 g
0.50“ x 0.40“ x 0.27“
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
-40°C~ 85°C
(See derating curve)
100°C
-40°C~125°C
Nature convection
Page: 1/3
Last update: 16.01.09
RD1-D10
1.0 Watt unregulated
dual output
NUMBER STRUCTURE
RD1 - XX
XX
D
Name/Package
RD1=DIL8
Output
03=3.3V
05=5V
Input
07=7.2V Type
05=5V 09=9V
S=Single
12=12V 12=12V D=Dual
24=24V 15=15V
18=18V
24=24V
DERATING CURVE
10
A
X
Power
Code
02=0.25W internal
05=0.50W
Isolation
07=0.75W
0=0.5 kVDC
10=1.00W
1=1.0 kVDC
15=1.50W
2=2.0 kVDC
20=2.00W
3=3.0 kVDC
30=3.00W
4=4.0 kVDC
5=5.0 kVDC
6=6.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RD1-0503D10AX
RD1-0505D10AX
RD1-0507D10AX
RD1-0509D10AX
RD1-0512D10AX
RD1-0515D10AX
RD1-0518D10AX
RD1-0524D10AX
RD1-1203D10AX
RD1-1205D10AX
RD1-1207D10AX
RD1-1209D10AX
RD1-1212D10AX
RD1-1215D10AX
RD1-1218D10AX
RD1-1224D10AX
RD1-2403D10AX
RD1-2405D10AX
RD1-2407D10AX
RD1-2409D10AX
RD1-2412D10AX
RD1-2415D10AX
RD1-2418D10AX
RD1-2424D10AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
30 / 285
30 / 277
30 / 277
30 / 263
30 / 300
30 / 263
30 / 263
30 / 300
15 / 119
15 / 115
15 / 115
15 / 109
15 / 125
15 / 109
15 / 109
25 / 128
10 / 58
10 / 57
10 / 57
10 / 55
10 / 62
10 / 54
10 / 54
10 / 62
±3.3
±5
±7.2
±9
±12
±15
±18
±24
±3.3
±5
±7.2
±9
±12
±15
±18
±24
±3.3
±5
±7.2
±9
±12
±15
±18
±24
±152
±100
±69
±56
±50
±33
±28
±25
±152
±100
±69
±56
±50
±33
±28
±25
±152
±100
±69
±56
±50
±33
±28
±25
70
72
72
76
80
76
76
80
70
72
72
76
80
76
76
78
71
73
73
75
80
77
77
80
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
±100
Page: 2/3
Last update: 16.01.09
RD1-D10
1.0 Watt unregulated
dual output
LOADING VS OUTPUT VOLTAGE
LOADING VS OUTPUT VOLTAGE
12 MODELS
Output Voltage
Output Voltage
5 MODELS
Load
MECHANICAL SPECIFICATIONS 8 Pin DIL
Load
PIN CONNECTIONS 8 Pin DIL
Pin Number
Dual 8 Pin DIL
1
4
5
7
8
-V Input
+V Input
+V Output
Common
-V Output
The Pin connections of high isolation models are the same as normal ones.
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 3/3
Last update: 16.01.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de