RV1-S15-D15 - RSG Electronic Components GmbH

RV1-S15/D15
15 Watt 2:1 regulated
single & dual output
2"x1" package, wide 2:1 input range
Full SMD technology
■ 1500 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 87%
■ -40°C~85°C operation temperature range
■ EMI complies with EN55022 class A
■
■
OUTPUT SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS (5)
Voltage accuracy
± 1%
Line regulation
± 0.5%
Load regulation (0% to 100% Load) Single ±0.5%, Dual ±1.0%
Ripple & Noise (20 MHz bandwith) (1)
100 mV pk-pk
Over current protection (of max. Iout)
140%
Short circuit protection
Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
Transient recovery time (3)
250us, typ.
Transient response deviation (3)
± 3% max.
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
12 modes
-0.7 ~ 25 VDC
24 modes
-0.7 ~ 50 VDC
48 modes
-0.7 ~ 100 VDC
Lead soldering temperature
260°C
INPUT SPECIFICATIONS
Voltage range
Start up time (nom. Vin and constant resistive load)
Max. input current
No-load input current
Input filter
Input reflected ripple current (4)
See table
20ms typ
See table
See table
Pi Type
35 mA pk-pk
GENERAL SPECIFICATIONS
Efficiency
I/O isolation voltage (3 sec.) Input / Output
Metal case / input & output
I/O isolation capacitance
I/O isolation resistance
Switching frequency
Humidity
Reliability calculated MTBF (MIL-HDBK-217F)
Safety standard (designed to meet)
See table
1500 VDC
1000 VDC
500 pF typ.
1000 M Ohm
typ. 200 kHz
95% rel. H
> 1.121 Mhrs.
IEC 60950-1
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
NOTE
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Tested by normal Vin and 25% load step change (75%50%-25% of Io).
4) Measured input reflected ripple current with a simulated
source inductance of 12uH.
5) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
6) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
7) Suggest adding external input filter (C1, C2, L) to meet
conducted emissions (EN55022 class A)
EMC CHARACTERISTICS
Radiated Emissions
EN55022
FCC 47 CFR Part 15 Subpart A
ESD
IEC61000-4-2
RS
IEC61000-4-3
Class A
Class A
Perf. crit. B
Perf. crit. A
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
Nickel-coated brass
Ø 1.0 mm brass solder-coated
Epoxy (UL94V-0 rated)
30 g
2“x1“x 0.4“
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
-40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
Page: 1/4
Last update: 20.04.09
RV1-S15/D15
15 Watt 2:1 regulated
single & dual output
NUMBER STRUCTURE
RV1 - XX
XX
Output
03=3.3V
05=5V
Input
07=7.2V
12=9-18V 09=9V
24=18-36V 12=12V
48=36-72V 15=15V
18=18V
24=24V
DERATING CURVE
S
Name/Package
RV1=2“x1“
15
Power
15=15W
A
1
Code
internal
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RV1-1203S15A1
RV1-1205S15A1
RV1-1207S15A1
RV1-1209S15A1
RV1-1212S15A1
RV1-1215S15A1
RV1-1218S15A1
RV1-1224S15A1
RV1-1203D15A1
RV1-1205D15A1
RV1-1207D15A1
RV1-1209D15A1
RV1-1212D15A1
RV1-1215D15A1
RV1-1218D15A1
RV1-1224D15A1
RV1-2403S15A1
RV1-2405S15A1
RV1-2407S15A1
RV1-2409S15A1
RV1-2412S15A1
RV1-2415S15A1
RV1-2418S15A1
RV1-2424S15A1
RV1-2403D15A1
RV1-2405D15A1
RV1-2407D15A1
RV1-2409D15A1
RV1-2412D15A1
RV1-2415D15A1
RV1-2418D15A1
RV1-2424D15A1
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
30 / 1031
30 / 1524
30 / 1506
30 / 1470
30 / 1470
30 / 1470
30 / 1470
30 / 1453
30 / 1562
30 / 1524
30 / 1506
30 / 1488
30 / 1488
30 / 1488
30 / 1470
30 / 1470
25 / 515
25 / 744
25 / 744
25 / 735
25 / 735
25 / 726
25 / 726
25 / 718
25 / 515
25 / 753
25 / 744
25 / 735
25 / 726
25 / 726
25 / 718
25 / 718
3.3
5
7.2
9
12
15
18
24
±3.3
±5
±7.2
±9
±12
±15
±18
±24
3.3
5
7.2
9
12
15
18
24
±3.3
±5
±7.2
±9
±12
±15
±18
±24
3000
3000
2083
1666
1250
1000
833
625
±1500
±1500
±1041
±833
±625
±500
±416
±312
3000
3000
2083
1666
1250
1000
833
625
±1500
±1500
±1041
±833
±625
±500
±416
±312
80
82
83
85
85
85
85
86
80
82
83
84
84
84
85
85
80
84
84
85
85
86
86
87
80
83
84
85
86
86
87
87
3300
3300
2200
1000
1000
680
470
470
±1000
±1000
±680
±470
±470
±330
±220
±220
3300
3300
2200
1000
1000
680
470
470
±1000
±1000
±680
±470
±470
±330
±220
±220
Page: 2/4
Last update: 20.04.09
RV1-S15/D15
15 Watt 2.1 regulated
single & dual output
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RV1-4803S15A1
RV1-4805S15A1
RV1-4807S15A1
RV1-4809S15A1
RV1-4812S15A1
RV1-4815S15A1
RV1-4818S15A1
RV1-4824S15A1
RV1-4803D15A1
RV1-4805D15A1
RV1-4807D15A1
RV1-4809D15A1
RV1-4812D15A1
RV1-4815D15A1
RV1-4818D15A1
RV1-4824D15A1
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
20 / 257
20 / 372
20 / 372
20 / 367
20 / 363
20 / 359
20 / 359
20 / 359
20 / 257
20 / 372
20 / 372
20 / 367
20 / 363
20 / 359
20 / 359
20 / 359
3.3
5
7.2
9
12
15
18
24
±3.3
±5
±7.2
±9
±12
±15
±18
±24
3000
3000
2083
1666
1250
1000
833
625
±1500
±1500
±1041
±833
±625
±500
±416
±312
80
84
84
85
86
87
87
87
80
84
84
85
86
87
87
87
3300
3300
2200
1000
1000
680
470
470
±1000
±1000
±680
±470
±470
±330
±220
±220
TEST CONFIGURATIONS INPUT
TEST CONFIGURATIONS OUTPUT
INPUT REFLECTED RIPPLE CURRENT TEST STEP
OUTPUT RIPPLE & NOISE MEASUREMENT TEST
Input reflected ripple current is measured through a source
inductor Lin (12uH) and a source capacitor Cin (47uF, ESR
<1.0M at 100kHz) at nominal input and full load.
To reduce Ripple & Noise it is recommended to use a 1uF
ceramic disk capacitor and a 10uF electrolytic capacitor at
the output.
Page: 3/4
Last update: 20.04.09
RV1-S15/D15
15 Watt 2:1 regulated
single & dual output
EFFICIENCY VS OUTPUT CURRENT
EFFICIENCY VS OUTPUT CURRENT
24 MODELS
Efficiency (%)
Efficiency (%)
12 MODELS
Load
EFFICIENCY VS OUTPUT CURRENT
Efficiency (%)
48 MODELS
Load
PIN CONNECTIONS
Pin Number
Single
Dual
1
2
3
4
5
+V Input
-V Input
+V Output
N.P.
-V Output
+V Input
-V Input
+V Output
Common
-V Output
Load
DIMENSIONS
MECHANICAL SPECIFICATIONS
RSG
■
RV1-XXXXX15A1
Notes:
All dimensions are typical
in millimeters (inches).
1) Pin diameter: 1.0 ± 0.05 (0.04 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 4/4
Last update: 20.04.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de