F-215 SUPPLEMENT FHSC–125–15.00–SEU–TTR (1,27 mm) .050" FHSC SERIES FHSC–115–10.00–TTL–SED HIGH SPEED CABLE ASSEMBLIES –TXX Mates with: SFM SPECIFICATIONS For complete specifications see www.samtec.com?FHSC Uses 38 AWG micro ribbon coax cable Header or Socket Termination –SXX Mates with: TFM Cable: 38 AWG coax micro ribbon Signal Routing: 50Ω Single-Ended Overall Length: (152 mm) 6" to (1 m) 40" standard Cable Flexing Life: >40,000 cycles Cable Bending Radius: <2,5 mm Plating: Au over 50µ" (1,27 µm) Ni Current Rating: 0.5 A per pin (6 adjacent pins powered) Propagation Delay: 4.5 nsec/meter Operating Temp Range: -25°C to +105°C RoHS Compliant: Yes APPLICATION (10,87) .428 ALSO AVAILABLE (MOV Required) Processing conditions will affect mated height. Rated @ 7dB Insertion Loss Cable Length FHSC 10" (254 mm) (1,27 mm) .050" pitch 2.0 GHz / 4.0 Gbps Performance and complete test data available at www.samtec.com?FHSC or contact [email protected] RECOGNITIONS For complete scope of recognitions see www.samtec.com/quality • Other wire AWG • Hot plugging • Other lengths • Other terminations • Other sizes Contact Samtec. FHSC 1 NO. POSITIONS PER ROW END TO END L 05, 10, 15, 20, 25, 30 –SM to –SM –SM to –EM –EM to –EM (15,24) .600 (Standard sizes) (19,81) .780 Surface or Edge Mount (socket only) END NO. 1 WIRE LENGTH END NO. 2 Specify END ASSEMBLIES from chart = Wire Length in Inches (44,45 mm) 01.75" minimum –2 OAL = Wire Length + L Wire Length ± (1,27) .050 02 Note: Design your High Speed Cable with Samtec’s High Speed Cable Solutionator® at www.samtec.com/hdr Note: This Series is nonstandard, non-returnable. END – TXX –SXX 02 END NO. 1 –4 30 = Pin 1 to Last Pin 30 30 30 30 30 30 30 30 END NO. 2 ASSEMBLY –SEU = Socket, Edge, Notch Up –SED = Socket, Edge, Notch Down WIRING REQUIREMENTS WIRING END OPTIONS OPTION 1 or 2 TTR, TBL, STL, SBR, SED to TTR, TBL, STL, SBR, SEU or TTL, TBR, STR, SBL, SEU to TTL, TBR, STR, SBL, SED 3 or 4 TTR, TBL, STL, SBR, SED to TTL, TBR, STR, SBL, SED or TTL, TBR, STR, SBL, SEU to TTR, TBL, STL, SBR, SEU 30 EDGE MOUNT B* (10,24) * Surface Mount End Options only. 30 30 –TTR =Terminal, Top, Notch Right –TTL = Terminal, 30 Top, Notch Left –TBR = Terminal, Bottom, Notch Right –TBL = Terminal, Bottom, Notch Left 30 –STR = Socket, Top, Notch Right –STL = Socket, 30 Top, Notch Left –SBR = Socket, Bottom, Notch Right 01 SBL = Socket, Bottom, Notch Left 30 (7,67) .302 B* .403 (9,22) .363 –3 = Pin 1 to Second Last Pin SURFACE MOUNT ASSEMBLY END 1 END 2 01 Note: NO. OF Contact Samtec POSITIONS A A for high speed (20,37) .802 –05 characterization. (28,37) 1.117 –10 Note: (32,39) 1.275 Cable lengths –15 longer than (43,36) 1,707 –20 40.00" (1 meter) (52,37) 2.062 –25 are not supported with (52,37) 2.062 –30 S.I. test data. –1 = Pin 1 to Pin 1 = Pin 1 to Pin 2 (24,38) .960 Important Note: For optimal performance, at least one transmission line must be dedicated to ground. For more information, go to www.samtec.com/cable_ builder/xhsc_grounding.aspx WIRING OPTION END 1 30 30 END 2 30 30 WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice.