TI TPS75425QPWPRG4

TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TPS752xxQ with RESET Output, TPS754xxQ with Power Good Output
FAST-TRANSIENT-RESPONSE 2-A LOW-DROPOUT VOLTAGE REGULATORS
FEATURES
DESCRIPTION
1
• 2-A Low-Dropout Voltage Regulator
• Available in 1.5 V, 1.8 V, 2.5 V, 3.3 V Fixed
Output and Adjustable Versions
• Open Drain Power-On Reset With 100ms Delay
(TPS752xxQ)
• Open Drain Power-Good (PG) Status Output
(TPS754xxQ)
• Dropout Voltage Typically 210 mV at 2 A
(TPS75233Q)
• Ultralow 75-μA Typical Quiescent Current
• Fast Transient Response
• 2% Tolerance Over Specified Conditions for
Fixed-Output Versions
• 20-Pin TSSOP PowerPAD™ (PWP) Package
• Thermal Shutdown Protection
The TPS752xxQ and TPS754xxQ devices are
low-dropout regulators with integrated power-on reset
and power-good (PG) functions respectively. These
devices are capable of supplying 2 A of output
current with a dropout of 210 mV (TPS75233Q,
TPS75433Q). Quiescent current is 75 μA at full load
and drops down to 1 μA when the device is disabled.
These devices are designed to have fast transient
response for larger load current changes.
23
Because the PMOS device behaves as a low-value
resistor, the dropout voltage is very low (typically
210 mV at an output current of 2 A for the
TPS75x33Q) and is directly proportional to the output
current. Additionally, because the PMOS pass
element is a voltage-driven device, the quiescent
current is very low and independent of output loading
(typically 75 μA over the full range of output current,
1 mA to 2 A). These two key specifications yield a
significant improvement in operating life for
battery-powered systems.
APPLICATIONS
•
•
•
Telecom
Servers
DSP, FPGA Supplies
The device is enabled when EN is connected to a
low-level input voltage. This LDO family also features
a sleep mode; applying a TTL high signal to EN
(enable) shuts down the regulator, reducing the
quiescent current to less than 1 μA at TJ = +25°C.
blank
blank
Typical Application Circuit
(Fixed Voltage Options)
VIN
3
4
PG or
RESET
IN
IN
SENSE
OUT
0.22 mF
5
EN
OUT
6
PG or RESET Output
7
8
VOUT
9
(1)
COUT
+
GND
47 mF
17
(1)
See Application Information for capacitor selection details.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
DESCRIPTION, CONTINUED
The RESET (SVS, POR, or power on reset) output of the TPS752xxQ initiates a reset in microcomputer and
microprocessor systems in the event of an undervoltage condition. An internal comparator in the TPS752xxQ
monitors the output voltage of the regulator to detect an undervoltage condition on the regulated output voltage.
When the output reaches 95% of its regulated voltage, RESET goes to a high-impedance state after a 100-ms
delay. RESET goes to a logic-low state when the regulated output voltage is pulled below 95% (that is, during an
overload condition) of its regulated voltage.
The TPS754xxQ has a power good terminal (PG) as an active high, open drain output for use with a power-on
reset or a low-battery indicator.
The TPS754xxQ and TPS752xxQ are offered in 1.5 V, 1.8 V, 2.5 V and 3.3 V fixed-voltage versions and in an
adjustable version (programmable over the range of 1.5 V to 5 V). Output voltage tolerance is specified as a
maximum of 2% over line, load, and temperature ranges. The TPS754xxQ and TPS752xxQ families are
available in a 20-pin TSSOP (PWP) package.
blank
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
VOUT (2)
PRODUCT
TPS752xxyyyz, TPS754xxyyyz
(1)
(2)
(3)
XX is nominal output voltage (for example, 15 = 1.5 V, 01 = Adjustable (3)).
YYY is package designator.
Z is package quantity.
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Custom fixed output voltages are available; minimum order quantities may apply. Contact factory for details and availability.
The TPS75x01 is programmable using an external resistor divider (see Application Information).
ABSOLUTE MAXIMUM RATINGS (1)
Over operating temperature range (unless otherwise noted).
PARAMETER
TPS752xxQ, TPS754xxQ
UNIT
–0.3 to +6
V
–0.3 to +16.5
V
Maximum RESET voltage (TPS752xxQ)
16.5
V
Maximum PG voltage (TPS754xxQ)
16.5
Input voltage range, VIN (2)
Voltage range at EN
Peak output current
Output voltage range at OUT, FB
Continuous total power dissipation
V
Internally limited
5.5
V
See Dissipation Ratings Table
Operating virtual junction temperature range, TJ
–40 to +125
°C
Storage junction temperature range , TSTG
–65 to +150
°C
2
kV
ESD rating, HBM
(1)
(2)
2
Stresses above these ratings may cause permanent damage to the device. Exposure to absolute maximum conditions for extended
periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other
conditions beyond those specified is not implied.
All voltages are with respect to network terminal ground.
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
DISSIPATION RATINGS
BOARD
(1)
(2)
PACKAGE
Low-K (1)
PWP
High-K (2)
PWP
AIRFLOW
(CFM)
TA < +25°C
DERATING FACTOR
ABOVE TA = +25°C
TA = +70°C
TA = +85°C
0
2.9 mW
23.5 mW/°C
1.9 W
1.5 W
300
4.3 mW
34.6 mW/°C
2.8 W
2.2 W
0
3W
23.8 mW/°C
1.9 W
1.5 W
300
7.2 W
57.9 mW/°C
4.6 W
3.8 W
This parameter is measured with the recommended copper heat sink pattern on a 1-layer, 5-in ‫נ‬5-in printed circuit board (PCB), 1-ounce
copper, 2-in ‫נ‬2-in coverage (4 in2).
This parameter is measured with the recommended copper heat sink pattern on a 8-layer, 1.5-in ‫נ‬2-in PCB, 1-ounce copper with layers
1, 2, 4, 5, 7, and 8 at 5% coverage (0.9 in2) and layers 3 and 6 at 100% coverage (6 in2). For more information, refer to TI technical brief
SLMA002.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
VIN
Input voltage range (1)
2.7
5.5
V
VOUT
Output voltage range
1.5
5
V
IOUT
Output current
TJ
(1)
Operating virtual junction temperature
MAX
0
2.0
A
–40
+125
°C
To calculate the minimum input voltage for your maximum output current, use the following equation: VIN(min) = VOUT(max) + VDO(max load).
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
ELECTRICAL CHARACTERISTICS
Over recommended operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 1 V; IOUT = 1 mA, VEN = 0 V,
COUT = 47 μF, unless otherwise noted. Typical values are at TJ = +25°C.
TPS752xxQ, TPS754xxQ
PARAMETER
MIN
TYP
MAX
0.98VOUT
VOUT
1.02VOUT
2.7 V < VIN < 5.5 V
1.470
1.5
1.530
1.8 V output
2.8 V < VIN < 5.5 V
1.764
1.8
1.836
2.5 V output
3.5 V < VIN < 5.5 V
2.450
2.5
2.550
3.3 V output
4.3 V < VIN < 5.5 V
3.234
3.3
3.336
Ground pin current
IOUT = 1 mA to 2 A
75
125
μA
Output voltage line regulation
VOUT + 1 V < VIN ≤ 5 V
0.01
0.1
%/V
Load regulation
IOUT = 1 mA to 2 A
VN
Output noise voltage
BW = 300 Hz to 50
kHz
VOUT = 1.5 V, COUT = 100 μF
VDO
Dropout voltage (3)
ICL
Output current limit
TSD
Shutdown
temperature
ISTBY
Standby current
IFB
FB input current
VOUT
IGND
(1)
(2)
ΔVOUT%/
VOUT (1), (2)
ΔVOUT%/ ΔIOUT
TEST CONDITIONS
Adjustable output
1.5 V ≤ VOUT ≤ 5.5 V
1.5 V output
TPS75433Q
TPS75233Q
VEN(HI)
High-level enable input voltage
Low-level enable input voltage
PSRR
RESET
(TPS752xxQ)
μVRMS
400
mV
VOUT = 0 V
3.3
4.5
A
FB = 1.5 V
°C
1
–1
10
μA
1
μA
2
V
0.7
Power-supply ripple rejection (2)
f = 100 Hz, COUT = 100 μF,
IOUT = 2 A, See (1)
Minimum input voltage for valid
RESET
IOUT(RESET) = 300 μA,
V(RESET) ≤ 0.8 V
Trip threshold voltage
VOUT decreasing
Hysteresis voltage
Measured at VOUT
Output low voltage
VIN = 2.7 V, IOUT(RESET) = 1 mA
Leakage current
V(RESET) = 5.5 V
60
1
92
1.3
V
98
%VOUT
0.5
0.15
IOUT(PG) = 300 μA, V(PG) ≤ 0.8 V
Trip threshold voltage
VOUT decreasing
Hysteresis voltage
Measured at VOUT
Output low voltage
IOUT(PG) = 1mA
Leakage current
V(PG) = 5.5 V
1.1
80
%VOUT
0.4
V
1
μA
ms
1.3
V
86
%VOUT
0.5
0.15
EN = VIN
–1
EN = 0 V
–1
%VOUT
0.4
V
1
μA
1
0
V
dB
100
Minimum input voltage for valid PG
Input current (EN)
(1)
(2)
60
210
RESET timeout delay
PG
(TPS754xxQ)
mV
IOUT = 2 A, VIN = 3.2 V
EN = VIN
VEN(LO)
V
1
+150
TPS75x01Q
UNIT
1
μA
Minimum VIN = (VOUT + 1 V) or 2.7 V, whichever is greater. Maximum VIN = 5.5 V.
If VOUT ≤ 1.8 V, then VIN(min) = 2.7 V, VIN(max) = 5.5 V:
Line Regulation (mV) = (%/V) ´
VOUT(VIN(Max) - 2.7V)
´ 1000
100
If VOUT ≥ 2.5 V, then VIN(min) = VOUT + 1 V, VIN(max) = 5.5 V:
Line Regulation (mV) = (%/V) ´
(3)
4
VOUT[VIN(Max) - (VOUT + 1V)]
´ 1000
100
Input voltage equals VOUT(Typ) – 100 mV; TPS75x33Q input voltage must drop to 3.2 V for this test.
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
FUNCTIONAL BLOCK DIAGRAMS
Adjustable Voltage Versions
IN
EN
PG or RESET
_
+
OUT
+
_
100 ms Delay
(for RESET Option)
R1
Vref = 1.1834 V
FB
R2
GND
External to the device
Fixed-Voltage Versions
IN
EN
PG or RESET
_
+
OUT
+
_
SENSE
100 ms Delay
(for RESET Option)
R1
Vref = 1.1834 V
R2
GND
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
PIN CONFIGURATIONS
TSSOP-20
PWP
(TOP VIEW)
GND/HEATSINK
1
20
GND/HEATSINK
NC
2
19
NC
IN
3
18
NC
IN
4
17
GND
EN
5
16
NC
PG or RESET
6
15
NC
FB/SENSE
7
14
NC
OUTPUT
8
13
NC
OUTPUT
9
12
NC
10
11
GND/HEATSINK
GND/HEATSINK
Table 1. PIN DESCRIPTIONS
TPS754xxQ, TPS752xxQ
6
NAME
TSSOP-20 (PWP)
PIN NO.
I/O
EN
5
I
Negative polarity enable (EN) input
FB/SENSE
7
I
Adjustable voltage version only; feedback voltage for setting output voltage of
the device. Not internally connected on adjustable versions. Sense input for
fixed options.
GND
17
GND/HEATSINK
1, 10, 11, 20
Ground
Ground/heatsink
IN
3, 4
NC
2, 12, 13, 14,
15, 16, 18, 19
OUTPUT
8, 9
O
RESET/PG
6
O
Submit Documentation Feedback
DESCRIPTION
I
Input voltage
Not connected
Regulated output voltage
TPS752xxQ devices only; open-drain RESET output.
TPS754xxQ devices only; open-drain power-good (PG) output.
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TPS752xxQ RESET Timing Diagram
VIN
Vres
(1)
Vres
t
VOUT
VIT+
(2)
(2)
VIT+
Threshold
Voltage
(2)
VIT-
Less than 5% of the
Output Voltage
(2)
VIT-
t
RESET
Output
100 ms
Delay
100 ms
Delay
Output
Undefined
Output
Undefined
t
(1)
Vres is the minimum input voltage for a valid RESET. The symbol Vres is not currently listed within EIA or JEDEC
standards for semiconductor symbology.
(2)
VIT: Trip voltage is typically 5% lower than the output voltage (95% VOUT). VIT– to VIT+ is the hysteresis voltage.
TPS754xxQ Power Good Timing Diagram
VIN
(1)
VPG
VPG
t
VOUT
VIT+
(2)
(2)
VIT+
Threshold
Voltage
(2)
VIT-
(2)
VIT-
t
PG
Output
Output
Undefined
Output
Undefined
t
(1)
VPG is the minimum input voltage for a valid Power Good. The symbol VPG is not currently listed within EIA or JEDEC
standards for semiconductor symbology.
(2)
VIT: Trip voltage is typically 17% lower than the output voltage (83% VOUT). VIT– to VIT+ is the hysteresis voltage.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE NO.
8
vs Output Current
Figure 3, Figure 4
VOUT
Output Voltage
vs Junction Temperature
Figure 5, Figure 6
vs Time
Figure 18
IGND
Ground Current
vs Junction Temperature
Figure 7
PSRR
Power-Supply Ripple Rejection
vs Frequency
Figure 8
Output Spectral Noise Density
vs Frequency
Figure 9
ZOUT
Output Impedance
vs Frequency
Figure 10
VDO
Dropout Voltage
vs Input Voltage
Figure 11
vs Junction Temperature
Figure 12
VIN
Input Voltage (Min)
LINE
Line Transient Response
Figure 14, Figure 16
LOAD
Load Transient Response
Figure 15, Figure 17
ESR
Equivalent Series Resistance
Submit Documentation Feedback
vs Output Voltage
vs Output Current
Figure 13
Figure 20, Figure 21
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS
Over operating temperature range (TJ= –40°C to +125°C) unless otherwise noted. Typical values are at TJ = +25°C.
TPS75x33Q
OUTPUT VOLTAGE
vs OUTPUT CURRENT
TPS75x15Q
OUTPUT VOLTAGE
vs OUTPUT CURRENT
3.305
1.503
VIN = 2.7 V
TJ = +25°C
VIN = 4.3 V
TJ = +25°C
1.502
VOUT
VOUT - Output Voltage - V
VOUT - Output Voltage - V
3.303
VOUT
3.301
3.299
1.501
1.500
1.499
3.297
1.498
3.295
0
500
1500
1000
1.497
2000
0
IOUT - Output Current - mA
500
1500
1000
2000
IOUT - Output Current - mA
Figure 3.
Figure 4.
TPS75x33Q
OUTPUT VOLTAGE
vs JUNCTION TEMPERATURE
TPS75x15Q
OUTPUT VOLTAGE
vs JUNCTION TEMPERATURE
3.37
1.53
3.35
1.52
VOUT - Output Voltage - V
VOUT - Output Voltage - V
1 mA
3.33
1 mA
3.31
3.29
2A
3.27
1.50
2A
1.49
1.48
3.25
3.23
-50
1.51
0
50
100
TJ - Junction Temperature - °C
Figure 5.
Copyright © 2000–2007, Texas Instruments Incorporated
150
1.47
-40
10
60
110
160
TJ - Junction Temperature - °C
Figure 6.
Submit Documentation Feedback
9
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ= –40°C to +125°C) unless otherwise noted. Typical values are at TJ = +25°C.
TPS75xxxQ
GROUND CURRENT
vs JUNCTION TEMPERATURE
85
100
VIN = 5 V
IOUT = 2 A
PSRR - Power-Supply Rejection Ratio - dB
90
TPS75x33Q
POWER-SUPPLY RIPPLE REJECTION
vs FREQUENCY
Ground Current - mA
80
75
70
65
60
55
50
-40
90
VIN = 4.3 V
COUT = 100 mF
IOUT = 1 mA
TJ = +25°C
80
70
60
50
40
30
20
VIN = 4.3 V
COUT = 100 mF
IOUT = 2 A
TJ = +25°C
10
10
60
110
0
10
160
100
100k
Figure 8.
TPS75x33Q
OUTPUT SPECTRAL NOISE DENSITY
vs FREQUENCY
TPS75x33Q
OUTPUT IMPEDANCE
vs FREQUENCY
10
VIN = 4.3 V
VOUT = 3.3 V
COUT = 100 mF
TJ = +25°C
1M
10M
1M
10M
1
COUT = 100 mF
IOUT = 1 mA
ZOUT - Output Impedance - W
Vn - Voltage Noise - nV/ÖHz
1.6
10k
Figure 7.
2.0
1.8
1k
f - Frequency - Hz
TJ - Junction Temperature - °C
1.4
IOUT = 2 A
1.2
1.0
0.8
0.6
1
10
-1
COUT = 100 mF
IOUT = 2 A
0.4
0.2
0
10
10
IOUT = 1 mA
100
1k
10k
50k
10
-2
10
100
1k
10k
100k
f - Frequency - Hz
f - Frequency - Hz
Figure 9.
Figure 10.
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ= –40°C to +125°C) unless otherwise noted. Typical values are at TJ = +25°C.
TPS75x01Q
DROPOUT VOLTAGE
vs INPUT VOLTAGE
TPS75x33Q
DROPOUT VOLTAGE
vs JUNCTION TEMPERATURE
350
300
IOUT = 2 A
300
250
IOUT = 2 A
VDO - Dropout Voltage - mV
VDO - Dropout Voltage - mV
TJ = +125°C
250
TJ = +25°C
200
150
TJ = -40°C
100
200
IOUT = 1.5 A
150
100
IOUT = 0.5 A
50
50
0
0
2.5
3.5
3
4.5
4
5
10
-40
VIN - Input Voltage - V
60
110
160
TJ - Junction Temperature - °C
Figure 11.
Figure 12.
INPUT VOLTAGE (MIN)
vs OUTPUT VOLTAGE
TPS75x15Q
LINE TRANSIENT RESPONSE
4.0
DVOUT - Change in
Output Voltage - mV
TA = +25°C
TA = +125°C
3.0
TA = -40°C
2.7
2.0
1.5
IOUT = 2 A
COUT = 100 mF
VOUT = 1.5 V
dV = 1 V
ms
dT
100
0
-100
VIN - Input Voltage - V
VIN - Input Voltage (Min) - V
IOUT = 2 A
1.75
2
2.25
2.5
2.75
VOUT - Output Voltage - V
Figure 13.
Copyright © 2000–2007, Texas Instruments Incorporated
3
3.25
3.5
4
3
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
t - Time - ms
Figure 14.
Submit Documentation Feedback
11
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ= –40°C to +125°C) unless otherwise noted. Typical values are at TJ = +25°C.
TPS75x33Q
LINE TRANSIENT RESPONSE
ILOAD = 2 A
CLOAD = 100 mF (Tantalum)
VOUT = 1.5 V
50
DVOUT - Change in
Output Voltage - mV
DVOUT - Change in
Output Voltage - mV
TPS75x15Q
LOAD TRANSIENT RESPONSE
0
-50
dV = 1 V
ms
dT
100
0
-100
VIN - Input Voltage - V
-100
IOUT - Output Current - A
IOUT = 2 A
COUT = 100 mF (Tantalum)
VOUT = 3.3 V
-150
2
1
5.3
4.3
0
1
2
3
4
5
6
7
8
9
0
10
0.3
0.4
0.5
0.6
0.7
0.8
t - Time - ms
Figure 16.
TPS75x33Q
LOAD TRANSIENT RESPONSE
TPS75x33QOUTPUT VOLTAGE
vs TIME (AT STARTUP)
ILOAD = 2 A
CLOAD = 100 mF (Tantalum)
VOUT = 3.3 V
50
0
-50
0.9
1.0
VIN = 4.3 V
TJ = +25°C
3.3
0
Enable Voltage - V
IOUT - Output Current - A
0.2
Figure 15.
-100
-150
1.5
0
0
1
2
3
4
5
6
t - Time - ms
Figure 17.
12
0.1
t - Time - ms
VOUT - Output Voltage - V
DVOUT - Change in
Output Voltage - mV
0
Submit Documentation Feedback
7
8
9
10
4.3
0
0
0.2
0.4
0.6
0.8
1.0
t - Time - ms
Figure 18.
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ= –40°C to +125°C) unless otherwise noted. Typical values are at TJ = +25°C.
Test Circuit for Typical Regions of Stability (Figure 20 and Figure 21) (Fixed Output Options)
VIN
To Load
IN
OUT
+
COUT
EN
RL
GND
ESR
Figure 19.
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs OUTPUT CURRENT
10
VOUT = 3.3 V
COUT = 100 mF
VIN = 4.3 V
TJ = +25°C
ESR -Equivalent Series Resistance- W
ESR -Equivalent Series Resistance- W
10
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs OUTPUT CURRENT
1
Region of Stability
0.1
0.05
VOUT = 3.3 V
COUT = 47 mF
VIN = 4.3 V
TJ = +25°C
1
Region of Stability
0.1
Region of Instability
Region of Instability
0.01
0.01
0
0.5
1.0
1.5
2.0
0
0.5
1.0
IOUT - Output Current - A
IOUT - Output Current - A
Figure 20.
Figure 21.
1.5
2.0
(1). Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor,
any series resistance added externally, and PWB trace resistance to COUT.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
APPLICATION INFORMATION
The TPS752xxQ and TPS754xxQ devices include four fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V and
3.3 V), and an adjustable regulator, the TPS75x01Q (adjustable from 1.5 V to 5 V).
Minimum Load Requirements
The TPS752xxQ and TPS754xxQ families are stable even at zero load; no minimum load is required for
operation.
Pin Functions
Enable (EN)
The EN terminal is an input that enables or shuts down the device. If EN is a logic high, the device is in
shutdown mode. When EN goes to logic low, then the device is enabled.
Power-Good (PG)—TPS754xxQ
The PG terminal is an open drain, active high output that indicates the status of VOUT (output of the LDO). When
VOUT reaches 83% of the regulated voltage, PG goes to a high impedance state. It goes to a low-impedance
state when VOUT falls below 83% (that is, an overload condition) of the regulated voltage. The open drain output
of the PG terminal requires a pullup resistor.
Sense (SENSE)
The SENSE terminal of the fixed output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network, and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and VOUT to filter noise is not recommended because these types of networks may cause the regulator
to oscillate.
Feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and VOUT to filter noise is not
recommended because these types of networks may cause the regulator to oscillate.
Reset (RESET)—TPS752xxQ
The RESET terminal is an open drain, active low output that indicates the status of VOUT. When VOUT reaches
95% of the regulated voltage, RESET goes to a high-impedance state after a 100-ms delay. RESET goes to a
low-impedance state when VOUT is below 95% of the regulated voltage. The open-drain output of the RESET
terminal requires a pullup resistor.
GND/HEATSINK
All GND/HEATSINK terminals are connected directly to the mount pad for thermal-enhanced operation. These
terminals could be connected to GND or left floating.
Input Capacitor
For a typical application, an input bypass capacitor (0.22 μF to 1 μF) is recommended for device stability. This
capacitor should be as close to the input pins as possible. For fast transient conditions where droop at the input
of the LDO may occur because of high inrush current, it is recommended to place a larger capacitor at the input
as well. The size of this capacitor depends on the output current and response time of the main power supply, as
well as the distance to the load (LDO).
14
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
Output Capacitor
As with most LDO regulators, the TPS752xxQ and TPS754xxQ require an output capacitor connected between
OUT and GND to stabilize the internal control loop. The minimum recommended capacitance value is 47 μF and
the ESR (equivalent series resistance) must be between 100 mΩ and 10 Ω. Solid tantalum electrolytic, aluminum
electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements described in
this section. Larger capacitors provide a wider range of stability and better load transient response.
This information, along with the ESR graphs (see Figure 20 and Figure 21), is included to assist in selection of
suitable capacitance for the user’s application. When necessary to achieve low height requirements along with
high output current and/or high load capacitance, several higher ESR capacitors can be used in parallel to meet
these guidelines.
ESR and Transient Response
LDOs typically require an external output capacitor for stability. In fast transient response applications, capacitors
are used to support the load current while the LDO amplifier is responding. In most applications, one capacitor is
used to support both functions.
Besides its capacitance, every capacitor also contains parasitic impedances. These parasitic impedances are
resistive as well as inductive. The resistive impedance is called equivalent series resistance (ESR), and the
inductive impedance is called equivalent series inductance (ESL). The equivalent schematic diagram of any
capacitor can therefore be drawn as shown in Figure 22.
RESR
LESL
C
Figure 22. ESR and ESL
In most cases one can neglect the effect of inductive impedance ESL. Therefore, the following application
focuses mainly on the parasitic resistance ESR..
Figure 23 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
IOUT
LDO
+
VESR
RESR
–
VIN
RLOAD
VOUT
COUT
Figure 23. LDO Output Stage With Parasitic Resistances ESR and ESL
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
In steady state operation (dc state condition), the load current is supplied by the LDO (solid arrow) and the
voltage across the capacitor is the same as the output voltage (V(COUT) = VOUT). This condition means that no
current is flowing into the COUT branch. If IOUT suddenly increases (that is, a transient condition), the following
events occur:
• The LDO is not able to supply the sudden current need because of its response time (t1 in Figure 24).
Therefore, capacitor COUT provides the current for the new load condition (the dashed arrow). COUT now acts
like a battery with an internal resistance, ESR. Depending on the current demand at the output, a voltage
drop occurs at RESR. This voltage is shown as VESR in Figure 23.
• When COUT is conducting current to the load, initial voltage at the load is VOUT = V(COUT) – VESR. As a result
of the discharge of COUT, the output voltage VOUT drops continuously until the response time t1 of the LDO is
reached and the LDO resumes supplying the load. From this point, the output voltage starts rising again until
it reaches the regulated voltage. This period is shown as t2 in Figure 24.
Figure 24 also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From the above discussion, the following conclusions can be drawn:
• The higher the ESR, the larger the droop at the beginning of load transient.
• The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
Conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
IOUT
VOUT
1
2
ESR 1
3
ESR 2
ESR 3
t1
t2
Figure 24. Correlation of Different ESRs and Their Influence to the Regulation of VOUT at a Load Step
From Low-to-High Output Current
16
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
Programming the TPS75x01Q Adjustable LDO Regulator
The output voltage of the TPS77x01Q adjustable regulator is programmed using an external resistor divider as
shown in Figure 25. The output voltage is calculated using Equation 1:
R
VOUT = Vref ´ (1 + 1 )
R2
(1)
Where:
•
Vref = 1.1834 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 40μA divider current. Lower value resistors can be
used, but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 30.1 kΩ
to set the divider current at approximately 40μA and then calculate R1 using Equation 2:
V
R1 = ( OUT - 1) ´ R2
Vref
(2)
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS75x01Q
VIN
IN
0.22 mF
PG/
RESET
PG or RESET Output
250 kW
VOUT
OUT
> 2.0 V
R1
EN
< 0.7 V
FB/SENSE
GND
COUT
R2
OUTPUT
VOLTAGE
R1
R2
UNIT
2.5 V
33.2
30.1
kW
3.3 V
53.6
30.1
kW
3.6 V
61.9
30.1
kW
NOTE: To reduce noise and prevent oscillation,
R1 and R2 must be as close as possible to the
FB/SENSE terminal.
Figure 25. TPS75x01Q Adjustable LDO Regulator Programming
Regulator Protection
The TPS752xxQ and TPS754xxQ PMOS-pass transistors have a built-in back diode that conducts reverse
currents when the input voltage drops below the output voltage (for example, during power down). Current is
conducted from the output to the input and is not internally limited. When extended reverse voltage is anticipated,
external limiting may be appropriate.
The TPS752xxQ and TPS754xxQ also feature internal current limiting and thermal protection. During normal
operation, the TPS752xxQ and TPS754xxQ limit output current to approximately 3.3 A. When current limiting
engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is
designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the
package. If the temperature of the device exceeds +150°C (typ), thermal-protection circuitry shuts it down. Once
the device has cooled below +130°C (typ), regulator operation resumes.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
Power Dissipation and Junction Temperature
Specified regulator operation is assured to a junction temperature of +125°C; the maximum junction temperature
should be restricted to +125°C under normal operating conditions. This restriction limits the power dissipation the
regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or
equal to PD(max).
The maximum-power-dissipation limit is determined using Equation 3:
TJ(Max) - TA
PD(Max) =
RqJA
(3)
where:
•
•
•
TJ(max) is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package; that is, 34.6°C/W for the 20-terminal PWP
with no airflow (see Dissipation Ratings Table).
TA is the ambient temperature
The regulator dissipation is calculated using Equation 4:
PD = (VIN - VOUT) ´ IOUT
(4)
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal
protection circuit.
THERMAL INFORMATION
Thermally-Enhanced TSSOP-20 (PWP–PowerPAD)
The thermally-enhanced PWP package is based on the 20-pin TSSOP, but includes a thermal pad [see
Figure 26(c)] to provide an effective thermal contact between the IC and the printed wiring board (PWB).
DIE
(a) Side View
Thermal
Pad
DIE
(b) End View
(c) Bottom View
Figure 26. Views of Thermally-Enhanced PWP Package
Traditionally, surface mount and power have been mutually exclusive terms. A variety of scaled-down
TO220-type packages have leads formed as gull wings to make them applicable for surface-mount applications.
These packages, however, suffer from several shortcomings: they do not address the very low profile
requirements (less than 2 mm) of many of today’s advanced systems, and they do not offer a pin-count high
enough to accommodate increasing integration. On the other hand, traditional low-power surface-mount
packages require power dissipation derating that severely limits the usable range of many high-performance
analog circuits.
The PWP package (a thermally-enhanced TSSOP) combines fine-pitch surface-mount technology with thermal
performance comparable to much larger power packages.
18
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
The PWP package is designed to optimize the heat transfer to the PWB. Because of the very small size and
limited mass of a TSSOP package, thermal enhancement is achieved by improving the thermal conduction paths
that remove heat from the component. The thermal pad is formed using a lead-frame design (patent pending)
and manufacturing technique to provide the user with direct connection to the heat-generating IC. When this pad
is soldered or otherwise coupled to an external heat dissipator, high power dissipation in the ultra-thin, fine-pitch,
surface-mount package can be reliably achieved.
Because the conduction path has been enhanced, power-dissipation capability is determined by the thermal
considerations in the PWB design. For example, simply adding a localized copper plane (heatsink surface) that is
coupled to the thermal pad enables the PWP package to dissipate 2.5 W in free air (see Figure 28(a), 8 cm2 of
copper heatsink and natural convection). Increasing the heatsink size increases the power dissipation range for
the component. The power dissipation limit can be further improved by adding airflow to a PWB/IC assembly
(see Figure 27 and Figure 28). The line drawn at 0.3 cm2 in Figure 27 and Figure 28 indicates performance at
the minimum recommended heatsink size, illustrated in Figure 30.
The thermal pad is directly connected to the substrate of the IC, which for the TPS752xxQPWP and
TPS754xxQPWP series is a secondary electrical connection to device ground. The heat-sink surface that is
added to the PWP can be a ground plane or left electrically isolated. In TO220-type surface-mount packages, the
thermal connection is also the primary electrical connection for a given terminal which is not always ground. The
PWP package provides up to 16 independent leads that can be used as inputs and outputs. (Note: leads 1, 10,
11, and 20 are internally connected to the thermal pad and the IC substrate.)
150
RqJA - Thermal Resistance - °C/W
Natural Convection
50 ft/min
100 ft/min
100
150 ft/min
200 ft/min
75
50
250 ft/min
300 ft/min
25
0 0.3
1
2
3
4
6
5
Copper Heatsink Area - cm
7
8
2
Figure 27. Thermal Resistance vs Copper Heatsink Area
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
19
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
3.5
3.5
TA = +25°C
TA = +55°C
300 ft/min
3.0
PD - Power Dissipation Limit - W
PD - Power Dissipation Limit - W
3.0
150 ft/min
2.5
2.0
Natural Convection
1.5
1.0
0.5
300 ft/min
2.5
2.0
150 ft/min
1.5
Natural Convection
1.0
0.5
0
0
0 0.3
2
6
4
Copper Heatsink Area - cm
8
0 0.3
2
4
2
Copper Heatsink Area - cm
(a)
6
8
2
(b)
3.5
TA = +105°C
PD - Power Dissipation Limit - W
3.0
2.5
2.0
1.5
150 ft/min
300 ft/min
1.0
Natural Convection
0.5
0
0 0.3
2
4
Copper Heatsink Area - cm
6
8
2
(c)
Figure 28. Power Ratings of the PWP Package at Ambient Temperatures of +25°C, +55°C, and +105°C
20
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
Figure 29 is an example of a thermally-enhanced PWB layout for use with the new PWP package. This board
configuration was used in the thermal experiments that generated the power ratings shown in Figure 27 and
Figure 28. As discussed earlier, copper has been added on the PWB to conduct heat away from the device. RθJA
for this assembly is illustrated in Figure 27 as a function of heatsink area. A family of curves is included to
illustrate the effect of airflow introduced into the system.
Heatsink Area
1 oz Copper
Board thickness
62 mils (0.15748 cm)
Board size
3.2 in. x 3.2 in.
Board material
FR4
Copper trace/heatsink
1 oz
Exposed pad mounting
63/67 tin/lead (Sn/Pb) solder
Figure 29. PWB Layout (Including Copper Heatsink Area) for Thermally-Enhanced PWP Package
From Figure 27, RθJA for a PWB assembly can be determined and used to calculate the maximum
power-dissipation limit for the component/PWB assembly, with the equation:
TJ(Max) - TA
PD(Max) =
RqJA (System)
(5)
Where TJmax is the maximum specified junction temperature (+150°C absolute maximum limit, +125°C
recommended operating limit) and TA is the ambient temperature.
PD(max) should then be applied to the internal power dissipated by the TPS75433QPWP regulator. The equation
for calculating total internal power dissipation of the TPS75433QPWP is:
PD(total) = (VIN - VOUT) ´ IOUT + VIN ´ IQ
(6)
Because the quiescent current of the TPS75433QPWP is very low, the second term is negligible, further
simplifying the equation to:
PD(total) = (VIN - VOUT) ´ IOUT
(7)
For the case where TA = +55°C, airflow = 200 ft/min, copper heat-sink area = 4 cm2, the maximum
power-dissipation limit can be calculated. First, from Figure 27, we find the system RθJA is 50°C/W; therefore, the
maximum power-dissipation limit is:
TJ(Max) - TA 125°C - 55°C
=
= 1.4 W
PD(Max) =
RqJA (System)
50°C/W
(8)
If the system implements a TPS75433QPWP regulator, where VIN = 5 V and IOUT = 800 mA, the internal power
dissipation is:
PD(total) = (VIN - VOUT) ´ IOUT = (5 - 3.3) ´ 0.8 = 1.36 W
(9)
Comparing PD(total) with PD(max) reveals that the power dissipation in this example does not exceed the calculated
limit. When it does, one of two corrective actions should be made: either raise the power-dissipation limit by
increasing the airflow or the heat-sink area, or loweri the internal power dissipation of the regulator by reducing
the input voltage or the load current. In either case, the above calculations should be repeated with the new
system parameters.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS752xxQ
TPS754xxQ
www.ti.com
SLVS242C – MARCH 2000 – REVISED OCTOBER 2007
Mounting Information
The primary requirement is to complete the thermal contact between the thermal pad and the PWB metal. The
thermal pad is a solderable surface and is fully intended to be soldered at the time the component is mounted.
Although voiding in the thermal-pad solder-connection is not desirable, up to 50% voiding is acceptable. The data
included in Figure 27 and Figure 28 are for soldered connections with voiding between 20% and 50%. The
thermal analysis shows no significant difference resulting from the variation in voiding percentage.
Figure 30 shows the solder-mask land pattern for the PWP package. The minimum recommended heat-sink area
is also illustrated. This is simply a copper plane under the body extent of the package, including metal routed
under terminals 1, 10, 11, and 20.
Minimum Recommended
Heatsink Area
Location of Exposed
Thermal Pad on
PWP Package
Figure 30. PWP Package Land Pattern
22
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
20-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS75201QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75201QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75201QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75201QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75215QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75215QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75215QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75215QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75218QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75218QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75218QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75218QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75225QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75225QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75225QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75225QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75233QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75233QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75233QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75233QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75401QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75401QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75401QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75401QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75415QPWP
ACTIVE
HTSSOP
PWP
20
CU NIPDAU
Level-2-260C-1 YEAR
70
Addendum-Page 1
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
20-Sep-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS75415QPWPG4
ACTIVE
HTSSOP
PWP
20
TPS75415QPWPR
ACTIVE
HTSSOP
PWP
TPS75415QPWPRG4
ACTIVE
HTSSOP
TPS75418QPWP
ACTIVE
TPS75418QPWPG4
70
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75418QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75418QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75425QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75425QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75425QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75425QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75433QPWP
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75433QPWPG4
ACTIVE
HTSSOP
PWP
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75433QPWPR
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS75433QPWPRG4
ACTIVE
HTSSOP
PWP
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
20-Sep-2007
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
TPS75201QPWPR
HTSSOP
PWP
20
2000
330.0
TPS75215QPWPR
HTSSOP
PWP
20
2000
TPS75218QPWPR
HTSSOP
PWP
20
2000
TPS75225QPWPR
HTSSOP
PWP
20
TPS75233QPWPR
HTSSOP
PWP
TPS75401QPWPR
HTSSOP
TPS75415QPWPR
HTSSOP
TPS75418QPWPR
16.4
6.95
7.1
1.6
8.0
16.0
Q1
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
HTSSOP
PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
TPS75425QPWPR
HTSSOP
PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
TPS75433QPWPR
HTSSOP
PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS75201QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75215QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75218QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75225QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75233QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75401QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75415QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75418QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75425QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
TPS75433QPWPR
HTSSOP
PWP
20
2000
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated