XFPM(NIBP) Data sheet Pre-amplified/5V Excitation/Gauge Features . . . . Applications . Non-invasive Blood Pressure(NIBP)monitors . Medical device Accuracy, 1.0 FS Volt level output On-chip amplification and temperature compensations Pre-calibration of offset voltage and span Part number for ordering XFPM - 050KP G R - P1 Prefix (NIBP) P1 : Accuracy 1.0 FS Model XFPM Rated pressure(Pa) Terminal leads direction (See Outline Diagram) No mark : Pressure type G : Gauge Pressure type R : Gauge pressure XFPM Model Package configuration Measurable pressure range (kPa) 0 50 Dual-In-line-Package (DIP) Part number for ordering XFPM-050KPG-P1 XFPM-050KPGR-P1 Specifications Model/Rated pressure 050KPG(R)-P1 Recommended operating conditions Pressure type Gauge pressure Rated pressure 50 Measurable pressure range 0 50 Pressure media Non-corrosive gas only Excitation voltage 5 0.25 Absolute maximum rating Maximum load pressure 250 Maximum excitation voltage 8 Operating temperature 40 125 Storage temperature 40 125 Operating humidity 30 80 (No dew condensation) Electric performances/characteristics (Excitation voltage Vcc=5.0V constant, Ambient temperature Ta=25 ) Current consumption less than 10 Output impedance less than 10 Source current less than 0.2 Sink current less than 2 Mechanical response time 2 (For the reference) Full scale span voltage 4.5 Offset voltage 1 0.2 0.045 4.7 0.045 Full scale span voltage 1 Accuracy 1,2 1.0 Note ; 1) Excluding input voltage error. 2) Excludes offset calibration error and temperature error of offset. 1 Unit kPa.abs kPa.abs VDC kPa.abs VDC RH mA mA mA msec V V V FS/0 50 XFPM(NIBP) Data sheet Pre-amplified/5V Excitation/Gauge Outline dimensions Unit (mm) XFPM 4 5 6 3 2 1 C0.5 3 2 4 3 14 1 4.5 0.6 Vent hole R1.5 15.24(600mil) 5 Pressure port 0.8 max 15 2.2 0.5 6 8 5 0.2 4 12 Terminal leads Labelled faceplate 6.8 2.8 Recommended footprint for PCB 6- 1.8(Diameter of lands) 2.54 2.54 0.5 60 1.2 2.54 2.54 6- 0.9(Diameter of through holes) 15.2 unit(mm) Unit (mm) XFPM-R 4 0.2 8 0.8 Pressure port 2.2 0.5 3 14 R1.5 4 5 6 3 2 4.5 1 15.24(600mil) 5 max 15 6 4 5 12 C0.5 1 2 0.6 Vent hole 3 Terminal leads Recommended footprint for PCB 2.54 2.54 6- 0.9(Diameter of through holes) 6- 1.8(Diameter of lands) 2.54 2.54 60 1.2 0.5 Labelled faceplate 2.8 6.8 15.2 2 unit(mm) Pre-amplified/5V Excitation/Gauge XFPM(NIBP) Data sheet Connection diagram XFPM Vcc(DC5V) Vcc Vout Vout GND C2 C1 Remarks : 1)C1 : Connect 680pF capacitor within 2cm distance from leads. 2) C2 : Connect 0.01 F or more capacitor within 2cm distance from leads. GND 3) 4 and 5 pins must be No Connection. Open them as floating ones completely, and do NOT connect to other line or each other. Note ; Please read instruction “Notes” before using the sensor. Fujikura reserves the right to change specifications without notice. If you have any questions regarding technical issues or specifications, please contact us. Sensor Engineering Department 5-1 Kiba 1-chome, Koto-ku, Tokyo 135-8512, Japan Phone +81-(0)3-5606-1072 Fax. +81-(0)3-5606-1538 3 E-mail : [email protected]