Filename: tfs 403a.doc Version 1.5 Vectron International 07.11.2008 Filter specification TFS 403A 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 10 °C dBm 140 Ω || -10,2 pF 137 Ω || - 8,8 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS 403A is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 403,5 MHz without any tolerance. The given values for both the relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. Value Insertion loss (Reference level) ae 4,8 Nominal frequency fN - Pass band PB - Amplitude ripple in PB p-p 0,8 Relative attenuation fN ....... arel dB Limit max. 5,5 dB 403,5 MHz dB fN ± 1,5 MHz max. 1,5 dB max. 3 dB fN ± 1,5 MHz - fN ± 4,5 MHz ...... fN ± fN ± 19,5 MHz ....... fN ± 2 fN ± 3 MHz 19,5 100 MHz MHz 28 40 45 dB dB dB min. min. min. 25 35 20 dB dB dB 12 dB min. 8 dB max. 10 Return loss within PB Input power level Temperature coefficient of frequency Tcf -20 ppm/K dBm - Operating temperature range - - 10 °C.. + 60 °C Storage temperature range - - 40 °C.. + 85 °C *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 403a.doc Version 1.5 Vectron International 07.11.2008 Filter specification TFS 403A 2/5 Filter characteristic 1.69 -1 1.54 -10 -2 1.39 -15 -3 1.24 -20 -4 1.09 -5 0.94 -6 0.79 -35 -7 0.64 -40 -8 0.49 -45 -9 0.34 -25 -30 -50 379.2 384.06 388.92 393.78 398.64 403.5 408.36 frequency in MHz 413.22 418.08 422.94 -10 400.5 427.8 401.1 401.7 402.3 402.9 403.5 404.1 frequency in MHz 404.7 405.3 405.9 delay in µs 0 -5 magnitude in dB magnitude in dB insertion loss: -5.63 dB 0 0.19 406.5 Construction and pin connection (All dimensions in mm) 7 403A ● W45 1 SQ 3,81 +0,2/-0,1 5 1 2 3 4 5 6 7 8 Input Input RF Return Ground Ground Output Output Ground Ground Date code: W X A ... Year + week 2008 2009 2010 3 5 0,1 7 0,6 12 0% % d 3 1,78 2,54 1 1,2 Max. Date code 1,78 50 Ohm Test circuit 1 L1 L2 2 5 SAW C1 6 L3 C2 3, 4, 7, 8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 403a.doc Version 1.5 Vectron International 07.11.2008 Filter specification TFS 403A 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; 5. ESD ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer Tape (all dimensions in mm) W Po Do : : : 12 4 1,5 1,75 ± 0,1 5,5 ± 0,05 0,75 2 ± 0,05 P1 : D1(min) : Ao : 8 ± 0,1 1,5 4,3 ± 0,1 Bo CT 4,3 9,5 : : EMBOSSED CARRIER TAPE ± 0,3 ± 0,1 + 0,1 E : F : G (min) : P2 : 3000 min 300 mm min 500 mm min 300 mm Do Po P2 E Ao F D1 CT W Bo G P1 ± 0,1 ± 0,1 COVER TAPE W2 Reel (all dimensions in mm): A : W1 : 330 12,4 + 2,0 W2 (max) : 18,4 N (min) : 50 C : 13 A -+0,5/ -0,2 C N W 1 The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. Markings on the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on its right. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 403a.doc Version 1.5 Vectron International 07.11.2008 Filter specification TFS 403A 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 403a.doc Vectron International Version 1.5 Filter specification 07.11.2008 TFS 403A 5/5 History Version Reason of Changes Name Date 1.0 generation of “Development specification” according to customer requirements Chilla 14.08.2002 1.1 add limit line 20 dB at 804-810 MHz Chilla 22.08.2002 1.2 limit line at 2 fN ±3 MHz corrected Chilla 26.08.2002 1.3 add of typical values and terminating impedances Pfeiffer 27.11.2002 1.4 change stability characteristics Strehl 13.12.2006 1.5 - add of filter characteristics - pin connection: typing error corrected Pfeiffer 07.11.2008 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.