Filename: tfs 370.doc Version 2.0 Vectron International 19.07.2013 Filter specification TFS 370 1/5 Measurement condition Ambient temperature: 23 °C Input power level: 0 dBm Terminating impedances *): for input: for output : 170 Ω // -0,50 pF 170 Ω // -0,50 pF Characteristics Remark: Reference level for the relative attenuation arel of the TFS 370 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 370 MHz without tolerance. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value tolerance/limit Insertion loss at 23°C ae = amin 3.3 dB 3.5 dB Insertion loss in OTR ae = amin 3.8 dB 4.0 dB Nominal frequency fN - Centre frequency fc 370 MHz Pass band ripple (at ambient temperature) within fN ± 10 MHz 1.5** dB max. Relative attenuation arel 1.30 dB max. 3 dB 60 dB min. 50 dB fN fN fN fN + …fN ± 10 MHz 80 MHz …fN - 100 MHz 35 MHz …fN - 55 MHz 25 MHz …fN + 57.5 fN + 57.5 MHz …fN + 82.5 fN +127.5 MHz …fN +152.5 Intermodulation MHz 2 dB** 60 dB min. 30 dB 25 dB min. 20 dB MHz 60 dB min. 40 dB MHz 60 db min. 57 dB - min. 20 dBm*** - max. 10 dBm - max. 12 V IP3 Input power lewel Permissible DC voltage 370 MHz VDC Operating temperature range - 25 °C ... + 75 °C Storage temperature range - 40 °C … + 85 °C Temperature coefficient of frequency TCf**** -72 ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. **) 2 dB bandwidth (fN ± 10 MHz) is guaranteed at ambient temperature (23°C). ***) intermodulation signals: fN + 1 MHz and fN + 2 MHz, each of 10 dBm ****) ∆fc(Hz) = Tcf(ppm/K) x (T - TA) x fCTA (MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 370.doc Version 2.0 Vectron International 19.07.2013 Filter specification TFS 370 2/5 Filter characteristic insertion loss: -3.32 dB 0 -8 -0.5 -16 -1 -24 -1.5 -32 magnitude in dB magnitude in dB insertion loss: -3.32 dB 0 -40 -48 -56 -2 -2.5 -3 -3.5 -64 -4 -72 -4.5 -80 270 295 320 345 370 395 420 frequency in MHz 445 470 495 -5 350 520 354 358 362 366 370 374 frequency in MHz 378 382 386 390 Construction and pin connection (All dimensions in mm) 7 5 370 ● D28 3 7 5 0,1 1,1 120° +0,15 1,1 Date code: D E F ... Year + week 2013 2014 2015 1,8 Max. 1 Date code Output Output RF Return Ground Ground Input Input RF Return Ground Ground 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 2,54 50 Ω test circuit L1 IN 1 C1 L2 5 SAW C2 OUT 2,3,4,6,7,8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 370.doc Version 2.0 Vectron International 19.07.2013 Filter specification TFS 370 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 Po : 4,00 Do : 1,50 E : 1,75 F : 5,50 G(min) : 0,75 P2 : 2,00 P1 : 8,00 D1(min) : 1,50 Ao : 5,30 Bo : 5,30 Ct : 9,2 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 370.doc Version 2.0 Vectron International 19.07.2013 Filter specification TFS 370 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 370.doc Vectron International Version 2.0 Filter specification 19.07.2013 TFS 370 5/5 History Version Reason of Changes Name Date 1.0 Generation of specification Pfeiffer 05.09.2002 1.1 Changing package Pfeiffer 09.09.2002 1.2 Change of specification of 2 dB bandwidth Dr. Sabah 21.10.2002 1.3 Change from development specification to filter specification; add typical values and terminating impedance Dr. Sabah 29.10.2002 2.0 Insertion loss in data table changed Schönbein 19.07.2013 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.