Filename: tfs 901.doc Version 1.1 Vectron International 25.02.2011 Filter specification TFS 901 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 Ω 50 Ω Characteristics Remark: The nominal frequency fN is fixed at 901,12 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative attenuation arel of the TFS 901 is the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. All specified data are met within the operating temperature range. Data typ. value Insertion Loss (reference level) ae 1,5 Nominal Frequency fN - Centre Frequency fC - Relative Attenuation tolerance / limit dB max. 3,0 dB 901,12 MHz 901,12 ± 0,32 MHz arel 852 MHz … 880 MHz 34 dB min. 25 dB 880 MHz … 889 MHz 28 dB min. 10 dB 910 MHz … 940 MHz 15 dB min. 10 dB 940 MHz … 950 MHz 36 dB min. 25 dB Operating Temperature Range - 23°C Operable Temperature Range - -30°C … +70°C Storage Temperature Range - -30°C … +70°C Temperature Coefficient of Frequency OTR TCf * -18 ppm/K - *) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 901.doc Version 1.1 Vectron International 25.02.2011 Filter specification TFS 901 2/5 Filter characteristic insertion loss: -1.56 dB 0 0 -0.5 -10 -1 -1.5 magnitude in dB magnitude in dB -20 -30 -40 -2 -2.5 -3 -3.5 -4 -50 -4.5 -60 850.7 860.7 870.7 880.7 890.7 900.7 910.7 frequency in MHz 920.7 930.7 940.7 -5 899.5 950.7 900 900.5 901 frequency in MHz 901.5 902 902.5 Construction and pin connection (All dimensions in mm) 7 5 901 ● B09 3 5 7 Year + week 2011 2012 2013 0,1 1,1 120° +0,15 1,1 Date code: B C D ... 1,8 Max. 1 Ground Input Ground Ground Ground Output Ground Ground Date code 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 2,54 50 Ω Test circuit L1 2 6 L2 1, 3, 4, 5, 7, 8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 901.doc Version 1.1 Vectron International 25.02.2011 Filter specification TFS 901 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 Po : 4,00 Do : 1,50 E : 1,75 F : 5,50 G(min) : 0,75 P2 : 2,00 P1 : 8,00 D1(min) : 1,50 Ao : 5,30 Bo : 5,30 Ct : 9,2 ± 0,1 P1 Date Code Do P2 W G Ct Bo F G E t Po Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 A C N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 901.doc Version 1.1 Vectron International 25.02.2011 Filter specification TFS 901 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 901.doc Vectron International Version 1.1 Filter specification 25.02.2011 TFS 901 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification S. Channaa 05.08.2008 1.1 - Change remark, add typical values and filter characteristic - Generation of filter specification S. Channaa 25.02.2011 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.