Filename: TFS869L.doc Version 2.0 Vectron International 16.11.2012 Filter specification TFS 869L 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 50 Ω 50 Ω Source: Load: 464 Ω || -1.1 pF 379 Ω || -1.2 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS869L is the maximum of the passband attenuation amax. The maximum of the passband attenuation amax is defined as the insertion loss ae. The nominal frequency fN is fixed at 869.2125 MHz without any tolerance. The values of the relative attenuation arel are guaranteed over the whole operating temperature range. The frequency shift of the filter within the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss ae 2.0 fN - PB - dB tolerance / limit max. 3.0 dB (reference level) Nominal frequency Passband 0.1 Passband variation + fN dB max. min. ± 12.5 1.0 kHz dB arel Relative attenuation fN 869.2125 MHz 1 MHz … fN 2 MHz … - 2 MHz 18 dB 900 MHz 20 dB - Input power level Operating temperature range OTR Storage temperature range Frequency inversion temperature Temperature coefficient of frequency TCf *** 15 min. 15 dB max. 10** dBm - - 10 °C ... + 55°C - - 40 °C ... + 85°C 23 °C -0.03 ppm/K2 dB *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) power durability requirement is 10 dBm for each 4 seconds per hour over lifetime ***) ∆fc(Hz) = Tcf(ppm/K2) x (T - To)2 x fCAT (MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS869L.doc Version 2.0 Vectron International 16.11.2012 Filter specification TFS 869L 2/5 Filter characteristic 0 0 -0.5 -5 -1 magnitude in dB magnitude in dB -10 -1.5 -2 -2.5 -3 -3.5 -15 -20 -25 -30 -4 -35 -4.5 -40 868.2125 868.7125 869.2125 frequency in MHz 869.7125 870.2125 849 854 859 864 869 874 frequency in MHz 879 884 889 Construction and pin connection (All dimensions in mm) 7 869L ● C46 1 SQ 3,81 +0,2/-0,1 5 3 5 0,1 7 0,6 12 0% % d 3 1,78 2,54 1 Ground Input Ground Ground Ground Output Ground Ground Date code: B C D ... Year + week 2011 2012 2013 1,2 Max. Date code 1 2 3 4 5 6 7 8 1,78 50 Ohm Test circuit L1 2 6 L2 SAW 1, 3, 4, 5, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS869L.doc Version 2.0 Vectron International 16.11.2012 Filter specification TFS 869L 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 4,30 ± 0,1 Bo : 4,30 ± 0,1 Ct : 9,2 ± 0,1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS869L.doc Version 2.0 Vectron International 16.11.2012 Filter specification TFS 869L 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS869L.doc Vectron International Version 2.0 Filter specification 16.11.2012 TFS 869L 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Noack 29.08.2011 2.0 - Change from development spec to filter spec - Temperature coefficient updated - Typical values added - Filter characteristic added Molke 16.11.2012 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.