Filename: tfs 433s.doc Version 1.6 Vectron International 16.01.2014 Filter specification TFS 433S 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The reference level for the relative attenuation arel of TFS 433S is the minimum of the pass band attenuation amin. This value is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The given values for the relative attenuation arel and the group delay ripple have to be reached at the frequencies given below, even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value tolerance / limit Insertion Loss (reference level) ae Nominal Frequency fN - Centre Frequency fC 433,92 MHz 5 MHz min. 1,71 MHz 0,45 dB max. 1 dB dB dB dB dB dB dB dB dB dB min. min. min. min. min. min. min. min. min. 37 52 42 52 37 12 34 50 40 dB dB dB dB dB dB dB dB dB Passband 1 Relative Attenuation - fN fN fN fN fN fN fN fN fN + + + + 3,8 433,92 dB MHz - arel 0,92 MHz ... fN 8,42 18,92 25,92 40,92 83,92 9,58 20,08 41,08 141,08 dB PB dB fN 3,1 - MHz MHz MHz MHz MHz MHz MHz MHz MHz … … … … … … … … … fN fN fN fN fN fN fN fN fN + + + + + 0,79 MHz 18,92 25,92 40,92 83,92 423,92 20,08 41,08 141,08 566,08 Operating Temperature Range MHz MHz MHz MHz MHz MHz MHz MHz MHz 50 60 65 70 68 25 50 65 45 OTR Storage Temperature Range Temperature Coefficient of Frequency Input Power Level - - 40 °C ... + 85 °C TCf * -35 - - 45 °C ... + 90 °C ppm/K max. 5 dBm *) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433s.doc Version 1.6 Vectron International 16.01.2014 Filter specification TFS 433S 2/5 0 0 -10 -10 -20 -20 -30 -30 magnitude in dB magnitude in dB Filter characteristic -40 -50 -60 -40 -50 -60 -70 -70 -80 -80 -90 -90 -100 100 200 300 400 500 600 frequency in MHz 700 800 900 -100 400 1000 410 420 430 440 450 frequency in MHz 460 470 480 Construction and pin connection (All dimensions in mm) 7 1 +0,20 433S ● E03 SQ 3,81 - 0,10 5 3 5 Year + week 2014 2015 2016 1,78 0,1 12 0° 7 Date code: E F G ... Date code 0,6 3 Output RF Return Output Ground Ground Input RF Return Input Ground Ground 1,2 Max. 2,54 1 1 2 3 4 5 6 7 8 1,78 50 Ohm Test circuit L1 6 5 2 SAW L2 1 3, 4, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433s.doc Version 1.6 Vectron International 16.01.2014 Filter specification TFS 433S 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 4,30 ± 0,1 Bo : 4,30 ± 0,1 Ct : 9,5 ± 0,1 P1 t Po PIN Marker P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433s.doc Version 1.6 Vectron International 16.01.2014 Filter specification TFS 433S 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433s.doc Vectron International Version 1.6 Filter specification 16.01.2014 TFS 433S 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification according to customer specification. Dr. Sabah 17.06.2003 1.1 - Filter specification, add oft typical values Dr. Sabah 19.08.2003 1.2 - Change relative attenuation - fN+ 156,08 MHz … fN +566,08 MHz typ. 50dB min. 45dB change to - fN+ 141,08 MHz … fN +566,08 MHz typ. 45dB min. 35dB M. Springfeldt 12.02.2004 1.3 - Remove mistake in relative attanuation M. Springfeldt 13.02.2003 1.4 - Change relative attenuation - fN+ 156,08 MHz … fN +566,08 MHz typ. 50dB min. 45dB change to - fN+ 141,08 MHz … fN +566,08 MHz typ. 45dB min. 40dB M. Springfeldt 26.02.2004 - Change Temperature Coefficient of Frequency - Change Packing M. Springfeldt 14.07.2004 - maximum input power updated Kortenbeutel 16.01.2014 1.5 1.6 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.