Filename: tfs 101.doc Version 2.5 Vectron International 18.12.2008 Filter specification Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 10 °C dBm 1300 1300 || -2 pF || -2 pF TFS 101 1/5 Characteristics Remark: The reference level for the relative attenuation arel of the TFS 101 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 101,255 MHz without any tolerance. The given values for both the relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data Insertion Loss (Reference Level) ae = amin Nominal Frequency fN Centre Frequency fC Amplitude Ripple in Pass Band fN ... fN ± 10 kHz Relative Attenuation typ. Value 3,4 dB Variation/ Limitation max. 5 dB - 101,255 MHz 101,258 MHz - 0,2 dB max. 0,5 dB 0,5 1 dB dB max. max. 2 3 dB dB dB dB dB dB dB dB min. min. min. min. min. min. 5 23 28 50 50 70 dB dB dB dB dB dB arel fN ± 10 fN ± 20 kHz ... fN ± kHz ... fN ± 20 25 kHz kHz fN ± 55 fN ± 80 fN ± 100 fN + 200 fN - 200 fN - 895 kHz ... fN ± kHz ... fN ± kHz ... fN ± kHz ... fN + kHz ... fN kHz ... fN - 80 100 200 400 895 925 kHz kHz kHz kHz kHz kHz Intermodulation Input Frequency Input Level I.M. Products 10 29 36 69 63 75 I.M. F1 F2 Group Delay Distortion fN ... fN ± 15 kHz GDD 1,5 + 100 kHz, + 200 kHz - 100 kHz, - 200 kHz - 30 dBm max.- 110 dBm µs max. 5 10 µs Input Power Level - max. Operating Temperature Range - - 25 °C ... + 75 °C - - 40 °C ... + 85 °C Storage Temperature Range Temperature Coefficient of Frequency TCf **) - 0,036 ppm/K² - Frequency Inversion Temperature T0 25 - °C dBm *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K²) x (T-T0)² x fTo(MHz) Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 101.doc Version 2.5 Vectron International 18.12.2008 Filter specification TFS 101 2/5 Construction and pin connection (All dimensions in mm) TFS 101 W51 Date code 50 1 2 3 4 5 6 7 8 9 10 11 12 Ground Ground Ground Ground Output Output RF Return Ground Ground Ground Ground Input Input RF Return Date code: W X A ... Year + week 2008 2009 2010 Test circuit 11 L1 C1 12 5 SAW L2 6 C2 1, 2, 3, 4, 7, 8, 9, 10 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 101.doc Version 2.5 Vectron International 18.12.2008 Filter specification TFS 101 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: DIN IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: Reel of empty components at start: Reel of empty components at start including leader: Trailer Tape (all dimensions in mm) W Po : : Do E F : : : 24 4 EMBOSSED CARRIER TAPE ± 0,3 ± 0,1 Po Do P2 1,5 + 0,1 1,75 ± 0,1 11,5 ± 0,1 G (min) : 1700 min 300 mm min 500 mm min 300 mm E Ao 0,60 F D1 P2 : P1 : D1(min) : 2 12 1,5 ± 0,1 ± 0,1 Ao : 7,1 ± 0,2 Bo : 13,9 ± 0,2 CT : 21,5 ± 0,1 CT W Bo G P1 COVER TAPE W 2 Reel (all dimensions in mm): A : W1 : W2 (max) : 330 24,40 +2,0 30,4 N (min) : 60 C : 13 ± 0,5/-0.2 A C N W 1 The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. Markings on the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on its right. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 101.doc Version 2.5 Vectron International 18.12.2008 Filter specification TFS 101 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 101.doc Vectron International Version 2.5 Filter specification 18.12.2008 TFS 101 5/5 History Version Reason of Changes Name Date 2.1 Add history. Herrler 01.08.2001 2.2 Add pin 1 marker. Correct definition of reference level for relative attenuation and for insertion loss. Add typical data. Add centre frequency. Dr. Wall 25.01.2002 2.3 Add pin 1 marker of package for bottom view. Change stability characteristics (vibration). Dr. Wall 30.01.2002 2.4 Correct bottom view of package drawing. Dr. Wall 19.03.2002 2.5 Change construction, 50 Strehl 18.12.2008 Test circuit and stability characteristics Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.