Vectron International Filter specification TFS224 1/5

Filename: tfs224.doc
Version 2.0
Vectron International
21.03.2014
Filter specification
TFS224
1/5
Measurement condition
Ambient temperature:
23 °C
Input power level:
0 dBm
Terminating impedances*):
input: 680 Ω ║-1.8 pF
output: 680 Ω ║-1.8 pF
Characteristics
Remark:
Reference level for the relative attenuation arel of the TFS224 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation
amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the
3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 224.0 MHz without tolerance. The given values for the relative
attenuation arel have to be reached at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency
TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
typ. value
Insertion loss
(Reference level)
ae = amin
3.5
Nominal frequency
fN
-
Centre frequency
fc
224.015
2 dB bandwidth
BW
178
Variation/ Limitation
dB
max
5.2
dB
224.0
MHz
MHz
-
kHz
min
100
kHz
Relative attenuation
fN
... fN ± 50
kHz
1
dB
max
2
dB
fN ±0.5
fN ± 1
fN ± 5
MHz
MHz
MHz
41
46
56
dB
dB
dB
min
min
min
10
20
40
dB
dB
dB
MHz ... fN ± 1
MHz ... fN ± 5
MHz ... fN ±200
arel
Temperature coefficient of the frequency
TCf**)
Frequency inversion temperature
To
-0.036
13
ppm/K2
-
°C
-
Operating temperature range
-
- 45 °C ... + 75 °C
Storage temperature range
-
- 40 °C ... + 85 °C
Input power level
-
max
10
dBm
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used. and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K2) x (T-T0)² x fTo(MHz).
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs224.doc
Version 2.0
Vectron International
21.03.2014
Filter specification
TFS224
2/5
Filter characteristic
insertion loss: -3.83 dB
0
16.27
-1
14.5444
-2
12.8188
-3
11.0932
-4
9.3676
-5
7.642
-6
5.9164
-70
-7
4.1908
-80
-8
2.4652
-90
-9
0.7396
-10
-20
S21 magnitude in dB
S21 magnitude in dB
-30
-40
-50
-60
-100
223
223.2
223.4
223.6
223.8
224
224.2
frequency in MHz
224.4
224.6
224.8
225
-10
223.8
223.84
223.88
223.92
223.96
224
224.04
frequency in MHz
224.08
224.12
224.16
S21 Group delay in µs
0
-0.986
224.2
Construction and pin connection
(All dimensions in mm)
S 224
●
E12
3
Date code
2 Max.
1
1
5,2 Max.
2,54 ±0,2
7,2 Max.
2,54 ±0,2
1
1
2
3
4
5
6
7
8
9
10
11
12
Input
Input RF Return
Ground
Ground
Ground
Ground
Output
Output RF Return
Ground
Ground
Ground
Ground
Date code:
E
F
G
...
Year + week
2014
2015
2016
0,80
50 Ω Test circuit 1
50 Ohm
L1
1
SAW
C1
L2
7
50 Ohm
C2
2, 3, 4, 5, 6, 8, 9, 10, 11, 12
50 Ω Test circuit 2
50 Ohm
C1
C2
1
L1
50 Ohm
7
SAW
L2
2, 3, 4, 5, 6, 8, 9, 10, 11, 12
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs224.doc
Version 2.0
Vectron International
21.03.2014
Filter specification
TFS224
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g. 1 ms. half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min. 10 cycles per
plane, 3 planes; DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 15 min. each / 100 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions, see page 4: "Air reflow temperature conditions"
ANSI/ESD S20.20-1999, class 1A for HBM
This filter is RoHS compliant (2011/65/EU)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
:16.00 +0.3/-0.1
Po
:4.00
± 0.1
Do
:1.50
+0.1/-0
E
:1.75
± 0.1
F
:7.50
± 0.1
G(min)
:0.75
P2
:2.00
± 0.1
P1
:8.00
± 0.1
D1(min)
:1.50
Ao
:5.40
± 0.1
Bo
:7.60
± 0.1
Ct
:13.3
± 0.1
P1
t
Po
P2
W
G
Ct
Bo
F
G
E
Do
PIN Marker
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
:16.4
+2/-0
W2(max) :22.4
N(min)
: 50
C
:13.0
+0.5/-0.2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs224.doc
Version 2.0
Vectron International
21.03.2014
Filter specification
TFS224
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max.
260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs224.doc
Vectron International
Version 2.0
Filter specification
21.03.2014
TFS224
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generate development specification according to customers requirement.
Sabah
08.07.2002
1.1
- Correct span for relative attenuation of 2 dB.
- Correct attenuation in lower stop band.
Dr. Wall
11.11.2002
1.2
-
Change from development to filter specification.
Add termination impedance for input and output.
Add typical data.
Add 50 Ω test circuits.
Dr. Wall
05.02.2003
2.0
-
Updated filter specification header and footer.
Included filter characteristics.
Updated construction and pin connection.
Corrected 50 Ω Test circuit 1 header.
Updated stability characteristics, reliability.
Updated air reflow temperature conditions.
Raura
21.03.2014
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.