Filename: tfs 1575.doc Version 1.4 Vectron International 07.06.2011 Filter specification TFS 1575 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 1575,42 MHz without tolerance or limit. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae 1,37 - Nominal frequency fN - PB - Passband 0,35 Pass band ripple max. 2,0 1575,42 fN dB max. ± dB MHz 1,2 MHz 1,0 dB aabs Absolute attenuation 0,3 dB tolerance / limit MHz … 1520 MHz 41 dB min. 39 dB 1625 MHz … 1630 MHz 47 dB min. 25 dB 1630 MHz … 2400 MHz 45 dB min. 40 dB 2400 MHz … 3000 MHz 37 dB min. 30 dB 1,38 : 1 VSWR within PB Operating temperature range OTR - TCf * -47 2:1 - 40 °C ... + 85 °C - Storage temperature range Temperature coefficient of frequency max. - 45 °C ... + 85 °C ppm/K - *) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575.doc Version 1.4 Vectron International 07.06.2011 Filter specification TFS 1575 2/5 0 -1 -20 -2 -30 -3 -40 -4 -50 -60 -6 -7 -80 -8 -90 -9 500 1000 1500 frequency in MHz 2000 2500 -10 1545 3000 6 -5 -70 -100 9 VSWR 0 -10 magnitude in dB m a g n itu d e in d B Filter characteristic 3 1551 1557 1563 1569 1575 1581 frequency in MHz 1587 1593 1599 0 1605 Construction and pin connection (All dimensions in mm) 5 6 4 G75 ● W41 1,2 Max. 3 2 1 1 12 23 34 45 56 6 Ground Ground Input Input Ground Ground Ground Ground Output Output Ground Ground Date code: S TDate code: UW ...X A ... Year + week 2004 Year + week 2005 2008 2006 2009 2010 Date code 0,1 3 0,75 3 ±0,15 1,5 1 6 0,6 0,6 4 50 Ohm Test circuit L1 2 5 L2 SAW 1, 3, 4, 6 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575.doc Version 1.4 Vectron International 07.06.2011 Filter specification TFS 1575 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 2000 Hz, 10 g respectively, 1 octave per min, 10 cycles per plan, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 – 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction P1 Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,3 ± 0,1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 180 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 60 C : 13,0 ± 0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575.doc Version 1.4 Vectron International 07.06.2011 Filter specification TFS 1575 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575.doc Vectron International Version 1.4 Filter specification 07.06.2011 TFS 1575 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification S.Boillat 24.2.2004 1.1 - Generation of filter specification - Change passband ripple - Change absolute attenuation - Change storage temperature range - Add filter characteristic - Add typical value - Add packing ( tape and reel ) Noack 02.03.2004 1.2 - Update of filter specification S.Springfeldt 09.10.2008 1.3 - Minor corrections of V1.2 S.Springfeldt 12.07.2010 1.4 - Change stability characteristics - tape & reel updated Noack 07.06.2011 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.