Filename: TFS180L.doc Version 2.2 Vectron International 28.02.2013 Filter specification TFS180L 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 205.51 Ω || -23.24 pF 141.63 Ω || - 31.49 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS180L is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 180,0 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme Data typ. Value Insertion loss (reference level) ae 8 Nominal frequency fN - Passband PB - Pass band ripple fN ...fN ± 4.0MHz (p-p) fN ±2 180 fN ± dB MHz 4.0MHz - dB max. 1 dB 0.4 … fN ± 4.0 MHz dB max. 1 dB ± ± 5.0 25.6 MHz MHz 2 38 dB dB max. min. 3 30 dB dB ± 35.8 MHz 47 dB min. 43 dB ± 50 MHz 49 dB min. 45 dB 444 ns max. ± 30 ns 17 dB min. 9 dB max. 10 fN ± ± fN ± 25.6 MHz … fN MHz … f N MHz … f fN ± 35.8 MHz … f N 4.0 9.25 max. arel Relative attenuation fN dB tolerance / limit N Absolute group delay within PB *** Return loss within PB - Input Power Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf ** - -40°C ... + 85 °C - -40 °C ... + 85 °C -18 ppm/K dBm - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆fc(Hz) = Tcf(ppm/K) x (T - TA) x fCAT (MHz) ***) Both delay and ripple variations are to be included, (temperature and manufacturing variations are also included). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS180L.doc Version 2.2 Vectron International 28.02.2013 Filter specification TFS180L 2/5 Filter characteristic 0.51 -1 0.5004 -20 -2 0.4908 -30 -3 0.4812 -40 -4 0.4716 -5 0.462 -6 0.4524 -70 -7 0.4428 -80 -8 0.4332 -50 -60 -90 0.4236 -9 -100 105 120 135 150 165 180 195 frequency in MHz 210 225 240 -10 170.07 255 delay in µs 0 -10 magnitude in dB magnitude in dB insertion loss: -7.56 dB 0 172.07 174.07 176.07 178.07 180.07 182.07 frequency in MHz 184.07 186.07 188.07 0.414 190.07 Construction and pin connection (All dimensions in mm) 9 10 7 S 180L ● B02 6 4 12 Date code 0,6 2,54 1 1, 8 +/-0,2 3 1 5 ,0 +/-0, 2 1 1 2 3 4 5 6 7 8 9 10 11 12 Ground Ground Ground Output Ground Output RF Return Ground Ground Ground Input Ground Input RF Return Date code: B C D ... 2,54 Year + week 2011 2012 2013 7 ,0 +/-0, 2 50 Ohm Test circuit 4 10 L2 12 SAW 6 L3 L4 1, 2, 3, 5, 7, 8, 9,11 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS180L.doc Version 2.2 Vectron International 28.02.2013 Filter specification TFS180L 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 16,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 7,50 ± 0,1 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,50 ± 0,1 Bo : 7,50 ± 0,1 Ct : 13,5 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Reel (all dimensions in mm) A : 330 W1 : 16,4 +2/-0 W2(max) : 22,4 N(min) : 50 C : 13,0 +0,5/-0,2 Ao W 2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS180L.doc Version 2.2 Vectron International 28.02.2013 Filter specification TFS180L 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217° C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS180L.doc Vectron International Version 2.2 Filter specification 28.02.2013 TFS180L 5/5 History Version Reason of changes Name Date 1.0 - Development specification TCUK 08.12.2011 2.0 - Add typical values, plots etc… and change development to filter specification. - As agreed with the customer, amend limits for loss, return loss & group delay ripple. TCUK 24.04.2012 2.1 - Removed RoHS compliance statement. TCUK 01.05.2012 2.2 - Now the TFS180L is standard part i.e. Pads NOT coated with SN60/Pb40 - Remove statement ‘Pads coated with SN60/Pb40’ - Include RoHS compliance statement. TCUK 28.02.2013 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.