Filename: tfs 456al.doc Version 1.2 Vectron International 05.11.2009 Filter specification TFS 456AL 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The reference level for the relative attenuation of the TFS456AL is the minimum attenuation in the pass band. The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 456,0 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae 2,0 Nominal frequency fN - PB Passband p-p Pass band variation MHz MHz 0,5 max. fN dB max. 3,5 ± dB 456,0 MHz 9,25 MHz 0,7 dB aabs Absolute attenuation 400 530 dB tolerance / limit … … 410 540 Group delay ripple within PB MHz MHz 65 55 dB dB min. min. 40 40 dB dB p-p 13 ns max. 15 ns - max. 10 dBm - - 10 °C ... + 75 °C Input power level Operating temperature range OTR - Storage temperature range Temperature coefficient of frequency TCf ** - 76 - 40 °C ... + 85 °C ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fT0 (MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 456al.doc Version 1.2 Vectron International 05.11.2009 Filter specification TFS 456AL 2/5 0 0.138 -1 0.126 -20 -2 0.114 -30 -3 0.102 -40 -4 0.09 -5 0.078 -6 0.066 -70 -7 0.054 -80 -8 0.042 -90 -9 0.03 -50 -60 -100 6 96 186 276 366 456 546 frequency in MHz 636 726 816 -10 436 906 440 444 448 452 456 460 frequency in MHz 464 468 472 delay in µs 0 -10 magnitude in dB magnitude in dB Filter characteristic 0.018 476 Construction and pin connection (All dimensions in mm) 456AL ● X45 1 2 3 4 5 6 7 8 Ground Input Ground Ground Ground Output Ground Ground Date code: X A B ... Year + week 2009 2010 2011 50 Ω Test circuit L1 2 6 L2 SAW 1, 3, 4, 5, 7, 8 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 456al.doc Version 1.2 Vectron International 05.11.2009 Filter specification TFS 456AL 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 4,30 ± 0,1 Bo : 4,30 ± 0,1 Ct : 9,5 ± 0,1 P1 Date Code Po Do P2 W G Ct Bo F G E t Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 A C N W 1 The minimum bending radius is 45 mm. Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 456al.doc Version 1.2 Vectron International 05.11.2009 Filter specification TFS 456AL 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 456al.doc Vectron International Version 1.2 Filter specification 05.11.2009 TFS 456AL 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Chilla 21.11.2007 1.1 - Change characteristics, change construction and pin connection - add test circuit Channaa 07.12.2007 1.2 - Add typical values and filter characteristic - Generation of filter specification Channaa 05.11.2009 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.