TFS434K - Vectron International

Filename: TFS434K.doc
Version 1.1
Vectron International
06.08.2013
Filter specification
TFS 434K
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
257 Ω || - 6.7 pF
313 Ω || - 5.5 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS434K is the minimum of the pass band attenuation. This value is defined as the insertion loss
ae. The nominal frequency fN is fixed at 434.0MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating
temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme.
Data
typ. value
ae
Insertion loss
(reference level)
PB
Passband
Pass band ripple fN ...fN ± 5.0 MHz
p-p
Relative attenuation
fN ±
… fN ±
20.0
dB
max.
13.0
fN
Nominal frequency
fN
10.8
tolerance / limit
MHz … fN ±
5.0
40
arel
MHz
MHz
dB
434.0
-
fN
0.27
dB
max.
0.27
dB
max.
dB
min.
53
±
5.0
MHz
MHz
0.6
dB
0.6
dB
40
dB
fN -
40
MHz … fN -
433
MHz ****
47
dB
min.
45
dB
fN +
40
MHz … fN +
536
MHz
58
dB
min.
45
dB
14
ns
max.
30
ns
23
dB
min.
10
dB
Group delay ripple within PB
p-p
Return loss within PB
Input Power
Operating temperature range
OTR
max.
-
- 40 °C ... + 85 °C
-
Storage temperature range
Temperature coefficient of frequency
-
TCf **
-18
7 ***
dBm
- 40 °C ... + 85 °C
ppm/K
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fcat(MHz).
***) Aim to update to the required +15dBm in December 2013, once we have our new metallisation.
****) Alternative matching (option 2 in our application note) gives better rejection in 1MHz...100MHz frequency range compared to our default matching stated
herein.
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS434K.doc
Version 1.1
Vectron International
06.08.2013
Filter specification
TFS 434K
2/5
Filter characteristic
0.54
-1
0.5112
-20
-2
0.4824
-30
-3
0.4536
-40
-4
0.4248
-5
0.396
-50
-60
-6
0.3672
-70
-7
0.3384
-80
-8
0.3096
-90
-9
0.2808
-100
334
354
374
394
414
434
454
frequency in MHz
474
494
514
534
-10
424.23
426.23
428.23
430.23
432.23
434.23
436.23
frequency in MHz
438.23
440.23
442.23
delay in µs
0
-10
magnitude in dB
magnitude in dB
insertion loss: -10.86 dB
0
0.252
444.23
Construction and pin connection
(All dimensions in mm)
7
434K
● D24
1
SQ 3,81 + 0,2/-0,1
5
3
1
2
3
4
5
6
7
8
Input
Input RF Return
Ground
Ground
Output
Output RF Return
Ground
Ground
Date code:
D
E
F
...
Year + week
2013
2014
2015
7
5
0,1
12
0%
0,6
%
d
3
1,78
2,54
1
1,2 Max.
Dat e code
1,78
50 Ω Test circuit
L1
1
2
5
SAW
L2
6
C2
C1
3, 4, 7, 8
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS434K.doc
Version 1.1
Vectron International
06.08.2013
Filter specification
TFS 434K
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2
HBM:250V;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direc tion
Tape (all dimensions in mm)
W
:12,00 ± 0,3
Po
:4,00
± 0,1
Do
:1,50
+0,1/-0
E
:1,75
± 0,1
F
:5,50
± 0,05
G(min)
:0,75
P2
:2,00
± 0,05
P1
:8,00
± 0,1
D1(min)
:1,50
Ao
:4,30
± 0,1
Bo
:4,30
± 0,1
Ct
: 9,5
± 0,1
P1
t
Po
P2
W
G
Ct
Bo
F
G
E
Do
PIN Marker
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
:12,4
+2/-0
W2(max) :18,4
N(min)
: 50
C
:13,0
+0,5/-0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS434K.doc
Version 1.1
Vectron International
06.08.2013
Filter specification
TFS 434K
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS434K.doc
Vectron International
Version 1.1
Filter specification
06.08.2013
TFS 434K
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
TCUK
07.05.2013
1.1
- Add typical values and move from development to filter specification
TCUK
06.08.2013
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.