Filename: tfs 1019.doc Version 3.0 Vectron International 31.08.2010 Filter specification TFS 1019 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The reference level for the relative attenuation arel of the TFS 1019 is the maximum attenuation in the pass band. The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 1019,5 MHz without any tolerance or limit. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) Nominal frequency ae 2,3 fN - Passband PB 0,3 Passband variation 1190 max. 3,5 dB 1019,5 MHz fN ± 15,5 MHz dB max. 1 dB dB min. 20 dB arel Relative attenuation 0,3 dB tolerance / limit MHz … 849 MHz 22 MHz … 3000 MHz 24 dB min. 20 dB @ 3057 MHz 34 dB min. 20 dB @ 4076 MHz 32 dB min. 20 dB @ 5095 MHz 14 dB min. 5 dB VSWR within PB 1,5 : 1 max. 2:1 Input power level - max. 10 - - 40 °C ... + 85 °C Operating temperature range OTR - Storage temperature range Temperature coefficient of frequency TCf ** -76 dBm - 40 °C ... + 85 °C ppm/K - **) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fCAT (MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1019.doc Version 3.0 Vectron International 31.08.2010 Filter specification TFS 1019 2/5 Filter characteristic 0 0 9 -1 -10 -2 -3 -30 6 -4 VSWR magnitude in dB m a g n itu d e in d B -20 -5 -6 -40 3 -7 -8 -50 -9 -60 500 1000 1500 2000 2500 3000 frequency in MHz 3500 4000 4500 5000 -10 960 5500 972 984 996 1008 1020 1032 frequency in MHz 1044 1056 1068 0 1080 Construction and pin connection (All dimensions in mm) 5 6 4 1,2 Max. A19 ● A36 2 1 1 2 3 4 5 6 Ground Input Ground Ground Output Ground Date code: A B C ... Year + week 2010 2011 2012 3 Date code 3 0,75 3,0 +/-0,15 0,30X0,30 1 0,6 6 4 0,6 50 Ohm Test circuit L1 2 5 L2 SAW 1, 3, 4, 6 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1019.doc Version 3.0 Vectron International 31.08.2010 Filter specification TFS 1019 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 9000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction P1 Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,5 ± 0,1 Date Code Do P2 W G Ct Bo F G E t Po Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1019.doc Version 3.0 Vectron International 31.08.2010 Filter specification TFS 1019 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1019.doc Vectron International Version 3.0 Filter specification 31.08.2010 TFS 1019 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Noack 23.12.2009 1.1 - Generation of filter specification and adding typical values S.Springfeldt 18.03.2010 2.0 - Updating the temperature coefficient after measurement S.Springfeldt 29.03.2010 3.0 - Extention of data table (enlargement of the high frequency stop band) S.Springfeldt 31.08.2010 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.