Filename: tfs 1575h.doc Version 3.0 Vectron International 28.06.2011 Filter specification TFS 1575H 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 403,13 Ω || -1,21 pF 375,40 Ω || -1,26 pF Characteristics Remark: The minimum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 1575,42 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss ae 3,0 Nominal frequency fN - Passband Pass band ripple 0,7 6,3 tolerance / limit dB max. 5,0 1575,42 dB MHz fN ± 1,4 MHz dB max. 1,5 dB MHz min. 3,5 MHz dB dB dB dB dB min. min. min. min. min. 30 20 20 30 35 Bandwidth 3 dB aabs Absolute attenuation 1500 1530 1585 1620 1630 MHz MHz MHz MHz MHz ... ... ... … ... 1530 1560 1620 1630 1710 MHz MHz MHz MHz MHz 40,6 29,4 37 34 37 VSWR within PB 1,8 : 1 max. 2,2 : 1 Input power level - max. 10 - - 40 °C ... + 85 °C Operating temperature range OTR - Storage temperature range Temperature coefficient of frequency TCf ** - 0,051 dB dB dB dB dB dBm - 45 °C ... + 90 °C ppm/K 2 - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆fc(Hz) = Tcf(ppm/K2) x (T - To)2 x fCAT (MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575h.doc Version 3.0 Vectron International 28.06.2011 Filter specification TFS 1575H 2/5 0 0 -5 -1 -10 -2 -15 -3 -20 -4 magnitude in dB magnitude in dB Filter characteristic -25 -30 -5 -6 -35 -7 -40 -8 -45 -9 -50 1425 1455 1485 1515 1545 1575 1605 frequency in MHz 1635 1665 1695 -10 1565 1725 1567 1569 1571 1573 1575 1577 frequency in MHz 1579 1581 1583 1585 Construction and pin connection (All dimensions in mm) 6 7 G75H ● B26 8 2 1 1,2 Max. 5 4 3 Date code 7 3,0 +/-0,15 0,6 d. Gr 60 0,6 Ground Input Ground Ground Ground Output Ground Ground Date code: B C D ... Year + week 2011 2012 2013 3 1,5 1 1 2 3 4 5 6 7 8 5 0,6 50 Ohm Test circuit L1 2 6 L2 SAW C2 C1 1, 3, 4, 5, 7, 8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575h.doc Version 3.0 Vectron International 28.06.2011 Filter specification TFS 1575H 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 9000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction P1 Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,5 ± 0,1 Date Code Po Do P2 W G Ct Bo F G E t Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575h.doc Version 3.0 Vectron International 28.06.2011 Filter specification TFS 1575H 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1575h.doc Vectron International Version 3.0 Filter specification 28.06.2011 TFS 1575H 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification S. Sabah 06.09.2005 1.1 - Add typ. value and filter characteristic - Change stability characteristics and generation of filter specification Strehl 05.04.2006 2.0 - adjust insertion loss, VSWR, passband ripple, stopband attenuation - typo in terminating impedance corrected Steiner 19.02.2010 3.0 - adjust insertion loss, terminating impedance and correct pinning S. Channaa 28.06.2011 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.