Signal conditioners with Functional Safety The MACX ranges Bro IE MACX Analog DE.indd 1 03.03.14 15:45 Reliable and safe MACX signal conditioners Maximum safety for your systems and machines: in all phases of the product lifecycle, MACX signal conditioners have been developed and produced according to standards for Functional Safety. Concept Development All safety-related functions are defined and assessed right from the creation of the product specification. Product development incorporates hazard and risk analyses as well as measures for ensuring the required safety integrity. A solution for every type of signal Maximum explosion protection Analog signals with performance level Safely isolate, adjust, filter, and amplify: MACX Analog offers comprehensive solutions for analog signal processing. Highly compact and leading technology: with a design width of just 12.5 mm, MACX Analog Ex offers single and two-channel signal isolators for intrinsically safe circuits in the hazardous area. With MACX Safety, you can integrate analog signals easily into your safety application according to the Machinery Directive, even for intrinsically safe circuits in the hazardous area. For more information, see page 6 onwards For more information, see page 16 onwards For more information, see page 10 onwards Ex approvals according to ATEX, IECEx 2 PhOENIX CONTACT Bro IE MACX Analog DE.indd 2 • Ex i for intrinsically safe circuits up to zone 0 and zone 20 • Ex n for installation in zone 2 03.03.14 15:45 Safety lifecycle Phoenix Contact meets the requirements of Functional Safety according to IEC 61508 in a standardized development process. We take measures for fault avoidance and fault control into consideration, from the very development and production of a device right up to device operation. Production Device operation During production, all of the defined specifications and test instructions are consistently implemented, verified, and validated. Certified safety offers the highest standard of quality and reliability during device operation. Tested quality and safety Independent test centers are involved throughout the entire development cycle and audit the measures as part of a full assessment. The certificates, technical information, and the safety manual are available for you to download. www.phoenixcontact.com Funcional Safety Type Approved ® TÜV Rheinland e ida Temperature control and monitoring with safe shutdown Temperature transducer MACX MCR-T-UIREL-UP Control valve Valve Open/closed Heat exchanger circuit Temperature sensor Temperature transducer MACX MCR-T-UI-UP The temperature in the tank is continuously controlled and monitored. Here, closed-loop control and the safety equipment are consistently isolated. In the event that the limit values are exceeded, the process is switched to the safe state via the additional temperature transducer. PhOENIX CONTACT Bro IE MACX Analog DE.indd 3 3 03.03.14 15:45 MACX signal conditioners Your advantages The MACX signal conditioner ranges combine high mechanical and electronic functionality in the same housing. Benefit from the many advantages of this consistent design. HART communication Bidirectional transmission of the HART communication signal for numerous analog IN/OUT product types. Flexible power supply Versions with wide range input enable worldwide use in power supply networks. Universal Power Input T-Connector Compatible Easy power bridging, system expansion or module replacement during operation with the modular DIN rail connector for 24 V versions. Choice of connection technology Wiring with screw connection or fast and tool-free push-in technology Convenient configuration Set standard functions directly on the front of the device via DIP switches. 4 PhOENIX CONTACT Bro IE MACX Analog DE.indd 4 Easy-maintenance connection terminal blocks Plug-in, coded connection terminal blocks with integrated test sockets. 03.03.14 15:45 Product overview Analog IN/ Analog OUT Signal conditioners • Universal and standard 3-way isolators • 3-way repeater power supplies (single and two-channel) • 3-way output isolators • 4-way signal duplicators MACX MACX MACX MACX Precise, interference-free signal transmission Precise and interference-free signal transmission, thanks to the patented transmitter concept with safe electrical isolation. Temperature TC/mV R/POTI - - + + Long service life and high operational reliability over the entire operating temperature range, thanks to low power consumption and self-heating. Page 17 Page 9 Page 14 Solenoid drivers - - + + Extended configuration and monitoring can be conveniently carried out via the PC with the free ANALOG-CONF software or via FDT/DTM. Page 8 Page 13 • Single and two-channel • Relay and transistor outputs • Signal duplicators MACX Analog MACX Analog Ex Digital OUT Easy configuration and monitoring Analog Analog Ex Safety Safety Ex NAMUR signal conditioners Digital IN + Page 17 • Universal and standard measuring transducers • 3-way measuring transducers • 4-way measuring transducers with switching output • Threshold value switches MACX MACX MACX MACX Long service life and high operational reliability Page 7 Page 12 Temperature transducers RTD - Analog Analog Ex Safety Safety Ex • Versions with various output characteristic curves for all solenoid valves on the market • Loop-powered versions • Versions with logic input MACX Analog Ex Page 15 Termination Carriers Page 18 Accessories Page 22 • Operator interface and display unit • Supply components • Programming adapter • HART multiplexer and more PhOENIX CONTACT Bro IE MACX Analog DE.indd 5 5 03.03.14 15:45 A solution for every type of signal MACX Analog Safely isolate, adjust, filter, and amplify: MACX Analog offers comprehensive solutions for analog signal processing. Save planning and operating costs by combining high signal flexibility with safe isolation and SIL evaluation. Universal temperature transducers • For RTD, TC, resistance-type sensors, mV voltages, and customerspecific characteristic curves • Universal power supply • Freely adjustable PDT relays as signal and alarm outputs Operator interface • On-site display of process values • Easy monitoring, configuration, and copying without software • Can be snapped onto a measuring transducer or DIN rail Analog signal conditioner • 1600 signal combinations • Easily adjustable via DIP switch • Short response time 6 PhOENIX CONTACT Bro IE MACX Analog DE.indd 6 Easy-maintenance connection terminal blocks Plug-in, coded connection terminal blocks with integrated test sockets. 03.03.14 15:45 MACX Analog – product overview Analog IN Analog IN Analog IN SIL 2 IN U,I U,I SIL 2 IN OUT POWER U,I U,I SIL 2 POWER OUT IN I POWER T-Connector Compatible OUT POWER T-Connector Universal Power Input Universal 3-way signal conditioner, configurable I Compatible Repeater power supply and input signal conditioner, HART-compatible Universal 3-way signal conditioner, configurable IN Unipolar: 0 … 50 mV to 0 … 100 V, 0 … 1 mA to 0 … 10 mA Bipolar: -50 … 50 mV to -100 … 100 V, -1 … 1 mA to -100 … 100 mA Live zero: 1 … 5 mA , 2 … 10 mA , 4 … 20 mA , 1 … 5 V, 2…10 V Configurable via DIP switch; for additional signal combinations, see data sheet Unipolar: 0 … 50 mV to 0 … 100 V, 0 … 1 mA to 0 … 10 mA Bipolar: -50 … 50 mV to -100 … 100 V, -1 … 1 mA to -100 … 100 mA Live zero: 1 … 5 mA , 2 … 10 mA , 4 … 20 mA , 1 … 5 V, 2…10 V Configurable via DIP switch; for additional signal combinations, see data sheet Input isolator operation: 4 … 20 mA (0 … 20 mA) Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) OUT Unipolar: 0 … 2.5 V, 0 … 5 V, 0 … 10 V, 0 … 5 mA , 0 … 10 mA, 0 … 20 mA Bipolar: -2.5 … 2.5 V, -5 … 5 V, -10 … 10 V, -5 … 5 mA, -10 … 10 mA, -20 … 20 mA Live zero: 1 … 5 mA , 2 … 10 mA, 4 … 20 mA, 0.5 … 2.5 V, 1 … 5 V, 2 … 10 V Configurable via DIP switch; for additional signal combinations, see data sheet Unipolar: 0 … 2.5 V, 0 … 5 V, 0 … 10 V, 0 … 5 mA , 0 … 10 mA, 0 … 20 mA Bipolar: -2.5 … 2.5 V, -5 … 5 V, -10 … 10 V, -5 … 5 mA, -10 … 10 mA, -20 … 20 mA Live zero: 1 … 5 mA , 2 … 10 mA, 4 … 20 mA, 0.5 … 2.5 V, 1 … 5 V, 2 … 10 V Configurable via DIP switch; for additional signal combinations, see data sheet Input isolator operation: 4 … 20 mA (0 … 20 mA) active/passive Repeater power supply operation: 4 … 20 mA active/passive 12.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-UI-UI-NC 2811446 MACX MCR-UI-UI-UP-NC 2811297 MACX MCR-SL-RPSSI-I 2865955 Push-in connection MACX MCR-UI-UI-SP-NC 2811556 MACX MCR-UI-UI-UP-SP-NC 2811569 MACX MCR-SL-RPSSI-I-SP 2924207 Analog IN Analog OUT Design width Analog IN SIL 2 SIL 2 POWER IN I I POWER T-Connector Compatible Repeater power supply and input signal conditioner with two outputs, HART-compatible SIL 2 OUT OUT I I IN POWER Universal Power Input Repeater power supply and input signal conditioner, HART-compatible Output signal conditioner, HART-compatible IN Input isolator operation: 4 … 20 mA (0…20 mA) Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) Input isolator operation: 4 … 20 mA (0…20 mA) Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) 4 … 20 mA (0 … 20 mA) With line fault detection OUT Input isolator operation: 4 … 20 mA (0 … 20 mA) per output, active Repeater power supply operation: 4 … 20 mA per output, active Input isolator operation: 4 … 20 mA (0 … 20 mA) active/passive, 1 … 5 V (0 … 5 V) Repeater power supply operation: 4 … 20 mA active/passive, 1…5V 4 … 20 mA (0 … 20 mA) With line fault detection T-Connector Compatible Configurable via DIP switch Design width 12.5 mm 17.5 mm 12.5 mm Screw connection MACX MCR-SL-RPSSI-2I 2924825 MACX MCR-SL-RPSSI-I-UP 2865968 MACX MCR-SL-IDSI-I 2865971 Push-in connection MACX MCR-SL-RPSSI-2I-SP 2924838 MACX MCR-SL-RPSSI-I-UP-SP 2924210 MACX MCR-SL-IDSI-I-SP 2924223 Versions with wide range input for worldwide power supply networks (MACX MCR-…-UP). The DIN rail connector enables the modular bridging of the 24 V supply voltage. T-Connector Compatible Bro IE MACX Analog DE.indd 7 PhOENIX CONTACT 7 Universal Power Input 03.03.14 15:45 MACX Analog – product overview Temperature Temperature SIL 2 T-Connector Compatible Temperature transducer for RTD sensors, configurable Temperature SIL 2 T-Connector Compatible Temperature transducer for TC sensors, configurable SIL 2 Universal Universal temperature transducer,Power Input with limit value relay, configurable IN RTD: PT 50, PT 100, PT 200, PT 500, PT 100S, PT 500S, Ni 100, Ni 500, Cu50, Cu53 Potentiometer: 0 … 2000 Ω Linear resistance: 0 … 2000 Ω Configurable via ANALOG-CONF or FDT/DTM TC: type E, J, K, N, L Voltages: -20 mV … 70 mV Configurable via ANALOG-CONF or FDT/DTM RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0…50 kΩ Linear resistance: 0…50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT OUT 0 … 20 mA, 4 … 20 mA (functionally safe) Configurable via ANALOG-CONF or FDT/DTM 0 … 20 mA , 4 … 20 mA (functionally safe) Configurable via ANALOG-CONF or FDT/DTM Analog: 0 … 20 mA, -10 … 10 V (freely scalable), 4 … 20 mA (functionally safe) Digital: 1 PDT relay Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT Design width 12.5 mm 12.5 mm 17.5 mm Screw connection MACX MCR-SL-RTD-I-NC 2865078 MACX MCR-SL-TC-I-NC 2924346 MACX MCR-T-UI-UP 2811394 Push-in connection MACX MCR-SL-RTD-I-SP-NC 2924320 MACX MCR-T-UI-UP-SP 2811860 Temperature SIL 2 Universal Universal temperature transducer,Power Input with three limit value relays, configurable IN RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0 … 50 Ω Linear resistance: 0 … 50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT OUT Analog: 0 … 20 mA, -10 … 10 V (freely scalable), 4 … 20 mA (functionally safe) Digital: 3 relay outputs, combination of relay 2 and 3 functionally safe Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT Design width 35.0 mm Screw connection MACX MCR-T-UIREL-UP 2811378 Push-in connection MACX MCR-T-UIREL-UP-SP 2811828 8 PhOENIX CONTACT Bro IE MACX Analog DE.indd 8 1) See accessory MACX MCR(-EX)-CJC 2) See accessory MACX MCR(-EX)-I20 03.03.14 15:45 MACX Analog – product overview Digital IN Digital IN Digital IN SIL 2 SIL 2 NAMUR signal conditioner, PDT output T-Connector Compatible NAMUR signal conditioner, two N/O contact outputs SIL 2 T-Connector Compatible T-Connector NAMUR signal conditioner, Compatible two-channel, N/O contact output IN NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off OUT 1 relay (PDT) 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 2 relays (N/O contacts) 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 1 relay (N/O contact) per channel 250 V AC (2 A) , 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch Design width Screw connection Push-in connection 12.5 mm 12.5 mm 12.5 mm MACX MCR-SL-NAM-2RO 2865010 MACX MCR-SL-2NAM-RO 2865049 MACX MCR-SL-NAM-R-SP 2924252 MACX MCR-SL-NAM-2RO-SP 2924265 MACX MCR-SL-2NAM-RO-SP 2924294 Digital IN Digital IN Digital IN MACX MCR-SL-NAM-R 2865997 SIL 2 NAMUR signal conditioner, two-channel, PDT output SIL 2 SIL 2 Universal Power Input NAMUR signal conditioner, two transistor outputs T-Connector Compatible NAMUR signal conditioner, two-channel, transistor output T-Connector Compatible IN NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off OUT 1 relay (PDT) per channel 250 V AC (2 A) , 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 2 transistor outputs, passive Switching voltage/current: max. 30 V DC/50 mA Switching frequency: max. 5 kHz Switching behavior configurable via DIP switch 1 transistor output per channel, passive Switching voltage/current: max. 30 V DC/50 mA Switching frequency: max. 5 kHz Switching behavior configurable via DIP switch Design width 17.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-SL-2NAM-R-UP 2865052 MACX MCR-SL-NAM-2T 2865023 MACX MCR-SL-2NAM-T 2865036 Push-in connection MACX MCR-SL-2NAM-R-UP-SP 2924304 MACX MCR-SL-NAM-2T-SP 2924278 MACX MCR-SL-2NAM-T-SP 2924281 Versions with wide range input for worldwide power supply networks (MACX MCR-…-UP). The DIN rail connector enables the modular bridging of the 24 V supply voltage. T-Connector Compatible Bro IE MACX Analog DE.indd 9 PhOENIX CONTACT 9 Universal Power Input 03.03.14 15:45 Maximum explosion protection MACX Analog Ex Highly compact and leading technology: with a design width of just 12.5 mm, MACX Analog Ex offers a wide range of single and two-channel signal isolators for intrinsically safe circuits in the hazardous area. The products are type-tested by an independent NAMUR test laboratory in accordance with NE 95 and therefore satisfy the high requirements of the chemical industry. HART communication Bidirectional transmission of the HART communication signal for all analog IN and analog OUT isolators. Suitable for all Ex zones and gas groups All MACX Analog Ex signal conditioners are approved in accordance with the applicable ATEX and IECEx standards: • Ex i – for intrinsically safe circuits up to zone 0 (gas) and zone 20 (dust) Marking: X II (1) G [Ex ia Ga] IIC; X II (1) D [Ex ia Da] IIIC • Ex n – for device installation in zone 2 Marking: X II 3(1) G Ex nA nC [ia Ga] IIC T4 Gc Relevant national approvals such as UL and GOST are available. Fast diagnostics LED indicators according to NE 44 for supply voltage, switching state, and fault. Hot-swappable module replacement Easy system expansion or module replacement during operation. Easy-maintenance connection terminal blocks 10 PhOENIX CONTACT Bro IE MACX Analog DE.indd 10 Plug-in, coded connection terminal blocks with integrated test sockets. 03.03.14 15:45 Power supply and diagnostics – flexible and easy with the DIN rail connector Easily bridge the 24 V supply voltage using the modular DIN rail connector. This simplifies wiring and enables system expansion or module replacement even during operation. The DIN rail connector offers two supply options: 1.2 2.2 3.2 N.C. N.C. 3.3 1.1 2.1 3.1 Power IN PWR PWR1 PWR2 ERR OUT1 1 2 ON OFF Group error message 1.2 2.2 3.2 OUT2 1 2 3 4 4.1 5.1 1.1 2.1 3.1 PWR OUT1 1.2 2.2 3.2 OUT2 1 2 3 4 I II 4.2 5.2 4.1 5.1 1.1 2.1 3.1 PWR OUT1 1.2 2.2 3.2 OUT2 1 2 3 4 I II 4.2 5.2 4.1 5.1 1.1 2.1 3.1 PWR OUT1 1.2 2.2 3.2 OUT2 1 2 3 4 I II 4.2 5.2 4.1 5.1 1.1 2.1 3.1 PWR OUT1 1.2 2.2 3.2 OUT2 1 4.2 5.2 4.1 5.1 PWR OUT1 1.2 2.2 3.2 OUT2 1 2 3 4 I II 1.1 2.1 3.1 MACX MCR-EX-SL-NAM-2RO 1.1 2.1 3.1 Power supply, redundant MACX MCR-EX-SL-NAM-2RO 3.3 MACX MCR-EX-SL-NAM-2RO 3.2 MACX MCR-EX-SL-NAM-2RO Power and fault monitoring module 3.1 MACX MCR-EX-SL-NAM-2RO Fault monitoring contact MACX MCR-EX-SL-NAM-2RO Precise and interference-free signal transmission, thanks to the patented transmitter concept with safe electrical isolation. 1. Direct supply Via any MACX Analog Ex module MACX MCR-PTB Precise, interference-free signal transmission 2 3 4 I II 4.2 5.2 4.1 5.1 I II 4.2 5.2 2. Via the power and fault monitoring module • Simple or redundant supply (decoupled from diode) • Fault monitoring output (message in the event of auxiliary voltage failure and line fault group message in the case of NAMUR signal conditioners) Long service life and high operational reliability Long service life and high operational reliability over the entire operating temperature range, thanks to low power consumption and self-heating. Maximum explosion protection with minimum space requirements With a housing width of just 12.5 mm for all single and two-channel 24 V devices, MACX Analog Ex offers space savings of up to 45% compared to other Ex i signal conditioners on the market. 125 mm 45% space saving Fast and error-free signal connection Compact Termination Carriers connect MACX Analog Ex devices to the automation system easily by means of plug and play. 160 mm 200 mm 225 mm PhOENIX CONTACT Bro IE MACX Analog DE.indd 11 11 03.03.14 15:45 MACX Analog Ex – product overview Analog IN Analog IN Analog IN SIL 2 SIL 2 POWER IN POWER IN I I OUT I I OUT SIL 3 POWER T-Connector IN OUT T-Connector Compatible Repeater power supply and input signal conditioner, HART-compatible Input isolator operation: 4 … 20 mA (0 … 20 mA) Compatible Repeater power supply and input signal conditioner with two outputs, HART-compatible Input isolator operation: 4 … 20 mA (0 … 20 mA) Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) Input isolator operation: 4 … 20 mA (0 … 20 mA) active/passive Input isolator operation: 4 … 20 mA (0 … 20 mA) per output, active Repeater power supply operation: 4 … 20 mA active/passive Repeater power supply operation: 4 … 20 mA per output, active Design width T-Connector Compatible Repeater power supply, two-channel, HART-compatible 4 … 20 mA per channel Transmitter supply voltage: > 16 V (20 mA) per channel 4 … 20 mA per channel, active 12.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-RPSSI-I 2865340 MACX MCR-EX-SL-RPSSI-2I 2865366 MACX MCR-EX-SL-RPSS-2I-2I 2865382 Push-in connection MACX MCR-EX-SL-RPSSI-I-SP 2924016 MACX MCR-EX-SL-RPSSI-2I-SP 2924236 MACX MCR-EX-SL-RPSS-2I-2I-SP 2924676 Analog IN Analog OUT SIL 2 SIL 2 OUT Universal Power Input Repeater power supply and input signal conditioner, HART-compatible Input isolator operation: 4…20 mA (0…20 mA) IN I I IN POWER Output signal conditioner, HART-compatible T-Connector Compatible 4 … 20 mA (0 … 20 mA) With cable break detection Repeater power supply operation: 4…20 mA Transmitter supply voltage: > 16 V (20 mA) OUT Input isolator operation: 4 … 20 mA (0 … 20 mA) active/passive, 1 … 5 V (0 … 5 V) 4 … 20 mA (0 … 20 mA) With cable break detection Repeater power supply operation: 4 … 20 mA active/passive, 1…5V Can be set via DIP switch Design width 17.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-RPSSI-I-UP 2865793 MACX MCR-EX-SL-IDSI-I 2865405 Push-in connection MACX MCR-EX-SL-RPSSI-I-UP-SP 2924029 MACX MCR-EX-SL-IDSI-I-SP 2924032 12 PhOENIX CONTACT Bro IE MACX Analog DE.indd 12 1) See accessory MACX MCR(-EX)-CJC 2) See accessory MACX MCR(-EX)-I20 03.03.14 15:45 MACX Analog Ex – product overview Temperature Temperature Temperature SIL 2 SIL 2 T-Connector Compatible Temperature transducer for RTD sensors, configurable Temperature transducer for TC sensors, configurable SIL 2 T-Connector Compatible Universal Universal temperature transducer,Power Input with limit value relay, configurable IN RTD: PT 50, PT 100, PT 200, PT 500, PT 100S, PT 500S, Ni 100, Ni 500, Cu50, Cu53 Potentiometer: 0 … 2000 Ω Linear resistance: 0 … 2000 Ω Configurable via ANALOG-CONF or FDT/DTM TC: type E, J, K, N, L Voltages: -20 mV … 70 mV Configurable via ANALOG-CONF or FDT/DTM RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0 … 50 kΩ Linear resistance: 0 … 50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT OUT 0 … 20 mA , 4 … 20 mA Configurable via ANALOG-CONF or FDT/DTM 0 … 20 mA , 4 … 20 mA Configurable via ANALOG-CONF or FDT/DTM Analog: 0 … 20 mA, -10 … 10 V (freely scalable), 4 … 20 mA (functionally safe) Digital: 1 PDT relay Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT Design width 12.5 mm 12.5 mm 17.5 mm Screw connection MACX MCR-EX-SL-RTD-I-NC 2865573 MACX MCR-EX-SL-TC-I-NC 2865586 MACX MCR-EX-T-UI-UP 2865654 Push-in connection MACX MCR-EX-SL-RTD-I-SP-NC 2924168 MACX MCR-EX-T-UI-UP-SP 2924689 Temperature SIL 2 U,I IN OUT POWER 3x Universal Universal temperature transducer,Power Input with 3 limit value relays, configurable IN RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0 … 50 kΩ Linear resistance: 0 … 50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT OUT Analog: 0 … 20 mA, -10 … 10 V (freely scalable), 4 … 20 mA (functionally safe) Digital: 3 relay outputs, combination of relay 2 and 3 functionally safe Configurable via ANALOG-CONF, FDT/DTM or IFS-OP-UNIT Design width 35.0 mm Screw connection MACX MCR-EX-T-UIREL-UP 2865751 Push-in connection MACX MCR-T-UIREL-UP-SP 2924799 The DIN rail connector enables the modular bridging of the 24 V supply voltage. T-Connector Compatible Bro IE MACX Analog DE.indd 13 Versions with wide range input for worldwide power supply networks (MACX MCR-EX-…-UP). PhOENIX CONTACT 13 Universal Power Input 03.03.14 15:45 MACX Analog Ex – product overview Digital IN Digital IN NAMUR signal conditioner, PDT output T-Connector Compatible Digital IN SIL 2 SIL 2 SIL 2 NAMUR signal conditioner, 2 N/O contact outputs T-Connector Compatible T-Connector NAMUR signal conditioner, Compatible two-channel, N/O contact output IN NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off OUT 1 relay (PDT) 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 2 relays (N/O contacts) 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 1 relay (N/O contact) per channel 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch Design width 12.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-NAM-R 2865434 MACX MCR-EX-SL-NAM-2RO 2865450 MACX MCR-EX-SL-2NAM-RO 2865476 Push-in connection MACX MCR-EX-SL-NAM-R-SP 2924045 MACX MCR-SL-EX-NAM-2RO-SP 2924061 MACX MCR-EX-SL-2NAM-RO-SP 2924087 Digital IN Digital IN Digital IN SIL 2 NAMUR signal conditioner, two-channel, PDT output Universal Power Input SIL 2 T-Connector NAMUR signal conditioner, Compatible single-channel, 2 transistor outputs SIL 2 NAMUR signal conditioner, two-channel, transistor output T-Connector Compatible IN NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off NAMUR proximity sensors Unused contacts or contacts with resistance circuit Line fault detection can be switched on/off OUT 1 relay (PDT) per channel 250 V AC (2 A), 120 V DC (0.2 A), 30 V DC (2 A) Switching behavior configurable via DIP switch 2 transistor outputs, passive Switching voltage/current: max. 30 V DC/50 mA Switching frequency: max. 5 kHz Switching behavior configurable via DIP switch 1 transistor output per channel, passive Switching voltage/current: max. 30 V DC/50 mA Switching frequency: max. 5 kHz Switching behavior configurable via DIP switch Design width 17.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-2NAM-R-UP 2865984 MACX MCR-EX-SL-NAM-2T 2865463 MACX MCR-EX-SL-2NAM-T 2865489 Push-in connection MACX MCR-EX-SL-2NAM-R-UP-SP 2924249 MACX MCR-EX-SL-NAM-2T-SP 2924074 MACX MCR-EX-SL-2NAM-T-SP 2924090 14 PhOENIX CONTACT Bro IE MACX Analog DE.indd 14 03.03.14 15:45 MACX Analog Ex – product overview Digital IN Digital OUT SIL 2 - OUT OUT + IN Digital OUT SIL 3 SIL 3 IN + POWER NAMUR signal conditioner, output with resistive behavior, with line fault transparency POWER T-Connector Compatible T-Connector Solenoid driver, with logic input and Compatible line fault detection, current limitation at 48 mA Solenoid driver, loop-powered, current limitation at 25 mA IN Switching level 0 signal (“L”): 0 … 5 V DC 20 … 30 V DC, 10 … 70 mA DC NAMUR proximity sensors Unused contacts or contacts with resistance Switching level 1 signal (“H”): 15 … 30 V DC (45 mA at Ue = 24 V DC) circuit Line fault detection can be switched on/off OUT Resistive behavior according to EN 60947-5-6 Switching voltage: 8.2 V DC Switching frequency: max. 5 kHz Switching behavior configurable via DIP switch Design width 9.5 V DC (at 48 mA) Current limitation: 48 mA Off-load voltage: 23 V DC Internal resistance: 269 Ω With line fault transparency and additional fault monitoring output T-Connector Compatible 5.5 V DC (at 25 mA) Current limitation: 25 mA Off-load voltage: 21.9 V DC Internal resistance: 641 Ω 12.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-NAM-NAM 2866006 MACX MCR-EX-SL-SD-23-48-LFD 2924867 MACX MCR-EX-SL-SD-21-25-LP 2865492 Push-in connection MACX MCR-EX-SL-NAM-NAM-SP 2924883 MACX MCR-EX-SL-SD-23-48-LFD-SP 2924870 MACX MCR-EX-SL-SD-21-25-LP-SP 2924113 Digital OUT Digital OUT Digital OUT SIL 3 SIL 3 SIL 3 T-Connector T-Connector Solenoid driver, loop-powered, Compatible current limitation at 40 mA Solenoid driver, loop-powered, Compatible current limitation at 48 mA Solenoid driver, loop-powered, current limitation at 58 mA IN 20 … 30 V DC, 10 … 95 mA DC (65 mA at Ue = 24 V DC) 20 … 30 V DC, 10 … 95 mA DC (75 mA at Ue = 24 V DC) 20 … 30 V DC, 10 … 105 mA DC (95 mA at Ue = 24 V DC) OUT 10 V DC (at 40 mA) Current limitation: 40 mA Off-load voltage: 21.9 V DC Internal resistance: 287 Ω 10.5 V DC (at 48 mA) Current limitation: 48 mA Off-load voltage: 24 V DC Internal resistance: 276 Ω 12.9 V DC (at 58 mA) Current limitation: 58 mA Off-load voltage: 21.9 V DC Internal resistance: 133 Ω Design width T-Connector Compatible 12.5 mm 12.5 mm 12.5 mm Screw connection MACX MCR-EX-SL-SD-21-40-LP 2865764 MACX MCR-EX-SL-SD-24-48-LP 2865609 MACX MCR-EX-SL-SD-21-60-LP 2865515 Push-in connection MACX MCR-EX-SL-SD-21-40-LP-SP 2924139 MACX MCR-EX-SL-SD-24-48-LP-SP 2924126 MACX MCR-EX-SL-SD-21-60-LP-SP 2924100 The DIN rail connector enables the modular bridging of the 24 V supply voltage. T-Connector Compatible Bro IE MACX Analog DE.indd 15 Versions with wide range input for worldwide power supply networks (MACX MCR-EX-…-UP). PhOENIX CONTACT 15 Universal Power Input 03.03.14 15:45 Analog signals with performance level MACX Safety Integrate analog signals easily into your safety application according to the Machinery Directive. The MACX Safety analog signal conditioners are certified according to EN ISO 13849-1 with performance level PL d. MACX Safety Ex also supports the safe processing of analog, intrinsically safe Ex signals. MACX Safety and MACX Safety Ex offer the following advantages: • Easy integration of analog signals into the safety chain, thanks to the performance level, PL d • Direct, safe switching of limit values possible without an additional safety controller • Easy planning of the safety application via SISTEMA • Easy to combine active or passive analog signals with other safety modules • Safe processing of intrinsically safe Ex signals with MACX Safety Ex [Ex ia] Ex approvals according to ATEX, IECEx • Ex i for intrinsically safe circuits up to zone 0 and zone 20 • Ex n for installation in zone 2 Easy-maintenance connection terminal blocks 16 PhOENIX CONTACT Bro IE MACX Analog DE.indd 16 Plug-in, coded connection terminal blocks with integrated test sockets. 03.03.14 15:45 MACX Safety – product overview Analog IN Temperature SIL 2 PL d SIL 2 PL d I IN OUT POWER T-Connector Compatible Repeater power supply and input signal conditioner with two outputs, HART-compatible Universal Universal temperature transducer,Power Input with limit value relay, configurable IN Input isolator operation: 4 … 20 mA Repeater power supply operation: 4 … 20 mA Transmitter supply voltage: > 16 V (20 mA) RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0 … 50 kΩ Linear resistance: 0 … 50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF or FDT/ DTM OUT Input isolator operation: 4 … 20 mA per output, active Repeater power supply operation: 4 … 20 mA per output, active Analog: 4…20 mA, active Digital: Combination of relay 2 and 3, functionally safe, 1 additional relay output Configurable via ANALOG-CONF or FDT/DTM Design width 12.5 mm 35.0 mm Screw connection MACX PL-RPSSI-2I 2904961 MACX PL-T-UIREL-UP Push-in connection MACX PL-RPSSI-2I-SP 2904962 MACX PL-T-UIREL-UP 2904901 2904903 MACX Safety Ex – product overview Analog IN Analog IN SIL 2 PL d POWER IN POWER IN I I I I Temperature SIL 3 PL d OUT OUT Repeater power supply and input signal conditioner with two outputs, HARTcompatible IN Input isolator operation: 4…20 mA Repeater power supply operation: 4…20 mA Transmitter supply voltage: > 16 V (20 mA) OUT Input isolator operation: 4 … 20 mA per output, active Repeater power supply operation: 4 … 20 mA per output, active Design width OUT POWER POWER T-Connector Compatible SIL 2 PL d I IN T-Connector Compatible Universal Universal temperature transducer,Power Input with limit value relay, configurable Repeater power supply, two-channel, HART-compatible Repeater power supply operation: 4 … 20 mA per channel Transmitter supply voltage: > 16 V (20 mA) per channel RTD: PT 10 … PT 10000, Ni 10 … Ni 10000, Cu10, Cu53, KTY TC 1): type B, E, J, K, N, R, S, T, L, U, C, D, A-1, A-2, A-3, M, L Potentiometer: 0 … 50 kΩ Linear resistance: 0 … 50 kΩ ±1000 mV, ±20 mA2) Configurable via ANALOG-CONF or FDT/DTM Repeater power supply operation: 4 … 20 mA per channel, active Analog: 4…20 mA, active Digital: Combination of relay 2 and 3, functionally safe, 1 additional relay output Configurable via ANALOG-CONF or FDT/DTM 12.5 mm 12.5 mm 35.0 mm Screw connection MACX PL-EX-RPSSI-2I 2904959 MACX PL-EX-RPSS-2I-2I 2904963 MACX PL-EX-T-UIREL-UP 2904910 Push-in connection MACX PL-EX-RPSSI-2I-SP 2904960 MACX PL-EX-RPSS-2I-2I-SP 2904964 MACX PL-EX-T-UIREL-UP-SP 2904912 1) See accessory MACX MCR(-EX)-CJC 2) See accessory MACX MCR(-EX)-I20 Bro IE MACX Analog DE.indd 17 The DIN rail connector enables the modular bridging of the 24 V supply voltage. T-Connector Compatible Universal Power Input Versions with wide range input for worldwide power supply networks (MACX MCR-EX-…-UP). PhOENIX CONTACT 17 03.03.14 15:45 Consistent interface solutions for system technology Termination Carrier 160 mm Using the compact Termination Carriers, you can connect MACX Analog devices to your automation system quickly and without any errors. You can establish the signal connection with standardized system cables by means of plug and play. The following standard DIN rail devices are available for safe signal conditioning: • Signal conditioners for Ex i circuits and SIL applications • Highly compact signal conditioners for non-Ex i circuits • Safe coupling relays for process automation The Termination Carrier concept • Stable aluminum profile without pitch markings with integrated DIN rail contour for accommodating standard interfaces • PCB protected in the profile, mechanically decoupled • Integrated DIN rail mounting with end bracket • Module connection by means of plug-in and coded cable sets • Cover with marking options Your consistent interface solution for system technology 18 1. Select a standard module 2. Termination Carrier Select the appropriate functions for signal conditioning from a wide range of standard DIN rail devices. Snap standard modules onto the integrated DIN rail contour in the profile. Connection to the Termination Carrier PCB is quick and safe with plug-in and coded cable sets. PhOENIX CONTACT Bro IE MACX Analog DE.indd 18 03.03.14 15:45 Compact 170 mm For high packing density • Space savings of up to 30 %, thanks to the compact design • Space-saving arrangement of connection points • Integrated end brackets Robust For high system availability • Stable and vibration-resistant aluminum carrier profile • Mechanically decoupled termination PCB • Passive PCB without active components • Redundant supply and monitoring electronics in a separate DIN rail device 242 mm Easy maintenance For simplified documentation and startup • Use of standard DIN rail devices • Easily accessible connection points • Module replacement during operation (hot swappable) • Pre-assembled system cabling with front adapter Flexible For optimum adaptation • Profile sections without pitch markings for controller-specific number of I/Os • Different system plug types, including redundant • Horizontal and vertical mounting 3. Front adapter with system cable The devices are connected to controller-specific I/O modules via highposition system cables. These cables have standardized or controller-specific system connections. and others PhOENIX CONTACT Bro IE MACX Analog DE.indd 19 19 03.03.14 15:45 Diagram of a typical system with point-to-point wiring Hazardous area Jumpering level Process control level 20 Interface level 17 18 19 20 Distributor boxes 20 Field devices Non-hazardous area 16 Output DC 40A Output DC 24 V 10 A Output DC 24 V 10 A 15 13 14 - - DC Ι< + + + OK Ι 13 14 - - DC Ι< + + + OK Ι N 13 14 N QUINT POWER QUINT POWER 11 10 9 8 7 Boost DC OK 18-29.5 V Input AC 100-240 V N L IN 1 IN 2 Input DC 12-24V 2x20A N 15 16 17 18 19 20 1 2 3 4 5 6 L QUINT DIODE 12 Boost DC OK 18-29.5 V Input AC 100-240 V 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 9 10 11 12 13 14 1 1 CH 16 17 CH 13 18 CH 14 19 20 CH 15 16 CH 12 15 CH 11 CH 12 11 10 9 8 7 CH 13 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 CH 11 6 CH 14 5 System cable CH 15 4 Master cable CH 16 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 CH 09 13 14 CH 10 Master cable 6 CH 15 5 CH 14 2 CH 12 3 4 CH 13 1 CH 11 Alarm 7 PW P W2 W PW2 PW1 4 5 6 PW 1 X20 0 8 9 10 11 12 13 14 15 16 17 CH 08 18 CH 09 19 20 CH 10 1 CH 15 2 3 CH 16 20 CH 14 19 CH 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CH 12 In the hazardous area, cables from intrinsically safe field devices are grouped together via distributor boxes to form multi-strand master cables. In the non-hazardous area, they are then routed to the interface level via marshalling distributors. From here the signal conditioners are individually wired to the relevant I/O cards. The significant amount of time needed for installation and startup is greatly reduced by the Termination Carrier and the use of plug and play system cables. Modular power concept for high availability X20 Alarm CH 01 PW PW 2 1 PW2 PW1 Connection for supply and fault monitoring output CH 07 CH 08 CH 09 CH 12 CH 11 CH 10 MACX Analog Ex signal conditioner CH 06 CH 05 CH 04 CH 03 N.C. N.C. 3.3 ON O O OFF FFF MACX MCR-PTB CH 02 1.2 2.2 3.2 1 2 Power and fault monitoring module 1.1 2.1 3.1 PWR1 ERR The termination PCB is therefore passive. It does not contain any active components whose failure would require the Termination Carrier to be replaced. 1 2 3 4 5 PWR2 The signal conditioners are connected to a power and fault monitoring module via the integrated DIN rail connectors. This enables redundant supply and monitoring electronics in a separate device. CH 16 CH 15 CH 14 CH 13 DIN rail connectors 6 7 8 9 10 0 20 PhOENIX CONTACT Bro IE MACX Analog DE.indd 20 03.03.14 15:46 Efficient signal connection with MACX Analog Ex In areas of process technology where potentially explosive atmospheres may occur, measuring and control circuits are usually designed with intrinsic safety protection type (Ex i). MACX Analog Ex i signal conditioners and measuring transducers isolate intrinsically safe circuits from nonintrinsically safe circuits at the interface level and safely limit the energy supplied to the hazardous area. Furthermore, they handle extensive signal conditioning tasks. Space-saving and fast installation The compact Termination Carrier solution enables you to integrate up to 384 signals in an 80 x 200 cm control cabinet when using two-channel MACX Analog Ex devices. Mounting and startup can be carried out quickly and without any errors using pre-assembled system cables. Termination Carriers In addition to universal Termination Carriers, numerous versions are available which are tailored to the I/O modules of various automation systems. Please contact us for more information. TC-D37SUB-ADIO16-EX-P-UNI Order No. 2924854 TC-D37SUB-AIO16-EX-PS-UNI Order No. 2902932 Universal Termination Carrier for 16 MACX MCR(-EX) isolators. Universal Termination Carrier for 16 MACX MCR(-EX) isolators with connection for HART multiplexer. and others PhOENIX CONTACT Bro IE MACX Analog DE.indd 21 21 03.03.14 15:46 Accessories for MACX Analog Operator interface Programming adapter DIN rail connector IFS-OP-UNIT Order No. 2811899 MACX-USB-PROG-ADAPTER Order No. 2811271 ME 6,2 TBUS-2 1,5/5-ST-3.81 GN Order No. 2869728 For process value display and parameterization, can be plugged directly onto 35 mm devices and the IFS-OP-CRADLE cradle unit. For programming the multifunctional devices with the ANALOG-CONF software or via FDT/DTM. For direct supply via any MACX Analog device or for supply via a power and fault monitoring module of the same shape. IFS-OP-CRADLE Order No. 2811886 Cradle for IF-OP-UNIT for connection to 17.5 mm/35 mm modules and use as a remote display unit. Power and fault monitoring module Dummy module MACX MCR-PTB Order No. 2865625 (screw connection) MACX MCR-EX-DUMMY-ISOLATOR MACX MCR-PTB-SP Order No. 2924184 (push-in connection) MACX MCR-EX-DUMMY-ISOLATOR-SP Order No. 2905846 (push-in connection) • Input voltage UIN: 19.2 … 30 V DC • Output voltage UOUT: UIN - max. 0.8 V, at 3.75 A • Error message - PDT relay Intrinsically safe dummy module with no electrical function for connecting unused signal cables. 22 Order No. 2904970 (screw connection) Function plug MACX MCR-CJC Order No. 2924993 MACX MCR-EX-CJC Order No. 2925002 Plug for cold junction compensation for thermocouples, in combination with MACX…-(EX)-T-UI… temperature transducers. MACX MCR-I20 MACX MCR-EX-I20 Order No. 2905680 Order No. 2905679 Connection terminal block for current signals (±20 mA) for safe switching of limit values, in combination with MACX…-(EX)-T-UI… temperature transducers. PhOENIX CONTACT Bro IE MACX Analog DE.indd 22 03.03.14 15:46 Accessories for MACX Analog Multiplexer for HART signals HART transfer board Shield fast connection MACX MCR-S-MUX Order No. 2865599 MACX MCR-S-MUX-TB Order No. 2308124 SSA 3-6 (for Ø 3 - 6 mm) Order No. 2839295 Multiplexer for the digital connection of HART-compatible field devices, such as measuring transducers or control valves, to a PC or a management system, 32-channel, including 14-wire flat-ribbon cable. Transfer board for connecting HART field devices to the HART multiplexer. SSA 5-10 (Ø 5 - 10 mm) Order No. 2839512 PSM-ME-RS232/RS485-P Order No. 2744416 For connecting cable shielding to cable terminal points, can be connected to PLUGTRAB PT. Electrically isolated interface converter for converting from RS-232 (V.24) to RS-485. Automatic data direction changeover or via RTS/CTS. Marking material UC-EMLP (11X9) (white) Order No. 0819291 Self-adhesive plastic labels for device marking: UniCard, 10-section, lettering field size: 11 x 9 mm. UC-EMLP (11X9) CUS (white) Order No. 0824547 As above, plus marked according to your specifications. For details, visit www.phoenixcontact.com. Test plug Resistance circuit MPS-MT Order No. 0201744 UKK 5-2R/NAMUR MPS-IH MPS-IH MPS-IH MPS-IH MPS-IH MPS-IH MPS-IH Order Order Order Order Order Order Order D-UKK 3/5 (gray) Order No. 2770024 D-UKK 3/5 BU (blue) Order No. 2770105 BK (black) GY (gray) GN (green) YE (yellow) BU (blue) RD (red) WH (white) No. No. No. No. No. No. No. Test plug for 2.3 mm Ø socket hole, consisting of MPS-MT metal part and MPS-IH… color insulating sleeve. 0201731 0201728 0201702 0201692 0201689 0201676 0201336 Order No. 2941662 Double-level terminal block with resistance circuit according to NAMUR for line fault detection in the case of mechanical contacts. Important: for intrinsically safe circuits, only in combination with D-UKK 3/5... cover. PhOENIX CONTACT Bro IE MACX Analog DE.indd 23 23 03.03.14 15:46 Always up-to-date, always available to you. Here you'll find everything on our products, solutions and service: phoenixcontact.com Product range • Industrial communication technology • Industrial Ethernet • Installation and mounting material • Lighting and signaling • Marking and labeling • Measurement and control technology • Modular terminal blocks • Monitoring • PCB terminal blocks and PCB connectors • Power supply units and UPS • Protective devices • Relay modules • Sensor/actuator cabling • Software • Surge protection and interference filters • System cabling for controllers • Tools • Wireless data communication PHOENIX CONTACT GmbH & Co. KG 32825 Blomberg, Germany Phone: +49 (0) 52 35 3-00 Fax: +49 (0) 52 35 3-4 12 00 phoenixcontact.com Bro IE MACX Analog DE.indd 24 IF 04-14.000.L3 MNR 52006465/2014-04-01/02 Printed in Germany © PHOENIX CONTACT 2014 • Cables and wires • Connectors • Controllers • Electronics housing • Electronic switchgear and motor control • Fieldbus components and systems • Functional safety • HMIs and industrial PCs • I/O systems 03.03.14 15:46