TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Rail-to-rail input/output 20 MHz GBP operational amplifiers Datasheet - production data Pin connections (top view) SOT23-5 Features • DFN8 2x 2 • • • • • • • • DFN6 1.3x1.6x0.55 IN- 1 6 VCC+ IN+ 2 5 VCC- NC 3 4 OUT Low input offset voltage: 1.5 mV max (A grade) Rail-to-rail input and output Wide bandwidth 20 MHz Stable for gain ≥ 4 or ≤ -3 Low power consumption: 820 µA typ High output current: 35 mA Operating from 2.5 V to 5.5 V Low input bias current, 1 pA typ ESD internal protection ≥ 5 kV Related products • See TSV911, TSV912, and TSV914 for unity-gain stable amplifiers Applications • • • • • MiniSO8, SO8 Battery-powered applications Portable devices Signal conditioning and active filtering Medical instrumentation Automotive applications Description The TSV99x and TSV99xA family of single, dual, and quad operational amplifiers offers low voltage operation and rail-to-rail input and output. These devices feature an excellent speed/power consumption ratio, offering a 20 MHz gainbandwidth, stable for gains above 4 (100 pF capacitive load), while consuming only 1.1 mA maximum at 5 V. They also feature an ultra-low input bias current. These characteristics make the TSV99x family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. These characteristics make the TSV99x, TSV99xA family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. SO14, TSSOP14 June 2015 DocID12833 Rev 11 This is information on a product in full production. 1/28 www.st.com Contents TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Contents 1 Absolute maximum ratings and operating conditions ................. 3 2 3 Electrical characteristics ................................................................ 5 Application information ................................................................ 14 4 5 6 2/28 3.1 Driving resistive and capacitive loads ............................................. 14 3.2 PCB layouts .................................................................................... 14 3.3 Macromodel .................................................................................... 14 Package information ..................................................................... 15 4.1 SOT23-5 package information ........................................................ 16 4.2 DFN8 2 x 2 (NB) package information ............................................ 17 4.3 DFN6 1.3 x 1.6 x 0.55 (NA - option 2) package information ............ 19 4.4 MiniSO8 package information ......................................................... 21 4.5 SO8 package information ................................................................ 22 4.6 SO14 package information .............................................................. 23 4.7 TSSOP14 package information ....................................................... 24 Ordering information..................................................................... 25 Revision history ............................................................................ 26 DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 1 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1: Absolute maximum ratings (AMR) Symbol VCC Vid Vin Iin Tstg Tj Rthja Parameter Supply voltage Value (1) Unit 6 Differential input voltage (2) ±VCC Input voltage (3) (VCC-) - 0.2 to (VCC+) + 0.2 Input current (4) 10 Storage temperature V mA -65 to 150 °C Maximum junction temperature 150 DFN8 2x2 57 DFN6 1.3x1.6x0.55 230 SOT23-5 250 SO8 125 MiniSO8 190 SO14 103 TSSOP14 100 SOT23-5 81 SO8 40 MiniSO8 39 SO14 31 TSSOP14 32 Thermal resistance (5)(6) junction to ambient °C/W Rthjc Thermal resistance junction to case HBM: human body model MM: machine model (7) (8) ESD CDM: charged device (9) model 5 kV 400 SOT23-5, SO8, MiniSO8, DFN8 2x2 1500 DFN6 1.3x1.6x0.55 TBD TSSOP14 750 SO14 500 Latch-up immunity 200 V mA Notes: (1) (2) (3) (4) (5) (6) Value is with respect to the VCC- pin Differential voltages are the non-inverting input terminal with respect to the inverting input terminal VCC - VIN must not exceed 6 V Input current must be limited by a resistor in series with the inputs Short-circuits can cause excessive heating and destructive dissipation Rth are typical values (7) Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. DocID12833 Rev 11 3/28 Absolute maximum ratings and operating conditions TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A (8) Machine model: 200 pF charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating (9) Charged device model: all pins plus packages are charged together to the specified voltage and then discharged directly to the ground. Table 2: Operating conditions Symbol 4/28 Parameter VCC Supply voltage Vicm Common mode input voltage range Top Operating free air temperature range Value 2.5 to 5.5 DocID12833 Rev 11 (VCC-) - 0.1 to (VCC+) + 0.1 -40 to 125 Unit V °C TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 2 Electrical characteristics Electrical characteristics In the electrical characteristic tables below, all parameter limits at temperatures other than 25 °C are guaranteed by correlation Table 3: Electrical characteristics at VCC+ = 2.5 V, VCC- = 0 V, Vicm = VCC/2, and RL connected to VCC/2, full temperature range (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA ∆Vio/∆T Top = 25 °C Tmin < Top < Tmax 7.5 Top = 25 °C 1.5 Tmin < Top < Tmax Input offset current, (1) (Vout = VCC/2) Iib Input bias current, (1) (Vout = VCC/2) Top = 25 °C Avd VCC VOH VOL Common mode rejection ratio, 20 log (ΔVic/ΔVio) Large signal voltage gain High level output voltage Low level output voltage Isink Iout Isource ICC Supply current (per channel) μV/°C 2 Iio CMR 3 Input offset voltage drift Top = 25 °C 1 Tmin < Top < Tmax 10 100 1 Tmin < Top < Tmax 10 pA 100 0 V to 2.5 V, Vout = 1.25 V, Top = 25 °C 58 Tmin < Top < Tmax 53 RL= 10 kΩ, Vout = 0.5 V to 2 V, Top = 25 °C 80 Tmin < Top < Tmax 75 75 dB 89 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 Vo = 2.5 V, Top = 25 °C 18 Tmin < Top < Tmax 16 Vo = 0 V, Top = 25 °C 18 Tmin < Top < Tmax 16 No load, Vout = VCC/2, Tmin < Top < Tmax mV mV 32 35 0.78 mA 1.1 AC performance GBP Gain Gain bandwidth product RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25 °C 20 MHz Minimum gain for stability Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, positive gain configuration 4 V/V DocID12833 Rev 11 5/28 Electrical characteristics Symbol Parameter TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Conditions Typ. Max. Unit Minimum gain for stability Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, negative gain configuration -3 V/V SR Slew rate RL = 2 kΩ, CL = 100 pF, Top = 25 °C 10 V/μs en Equivalent input noise voltage f = 10 kHz, Top = 25 °C 21 nV/√Hz Total harmonic distortion G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 2 Vpp, Top = 25 °C 0.0025 % Gain THD+N Notes: (1) Min. Guaranteed by design 6/28 DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Electrical characteristics Table 4: Electrical characteristics at VCC+ = 3.3 V, VCC- = 0 V, Vicm = VCC/2, and RL connected to VCC/2, full temperature range (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA ∆Vio/∆T Top = 25 °C Tmin < Top < Tmax 7.5 Top = 25 °C 1.5 Tmin < Top < Tmax Top = 25 °C Iib Input bias current, (1) (Vout = VCC/2) Top = 25 °C Avd VCC VOH VOL Common mode rejection ratio, 20 log (ΔVic/ΔVio) Large signal voltage gain High level output voltage Low level output voltage Isink Iout Isource ICC Supply current (per channel) μV/°C 2 Input offset current, (1) (Vout = VCC/2) CMR 3 Input offset voltage drift Iio 1 Tmin < Top < Tmax 10 100 1 Tmin < Top < Tmax 10 pA 100 0 V to 3.3 V, Vout = 1.65 V, Top = 25 °C 60 Tmin < Top < Tmax 55 RL= 10 kΩ, Vout = 0.5 V to 2.8 V, Top = 25 °C 80 Tmin < Top < Tmax 75 78 dB 90 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 Vo = 3.3 V, Top = 25 °C 18 Tmin < Top < Tmax 16 Vo = 0 V, Top = 25 °C 18 Tmin < Top < Tmax 16 No load, Vout = VCC/2, Tmin < Top < Tmax mV mV 32 35 0.8 mA 1.1 AC performance GBP Gain SR Gain bandwidth product Minimum gain for stability Slew rate RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25 °C 20 Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, positive gain configuration 4 Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, negative gain configuration -3 RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25 °C 10 DocID12833 Rev 11 MHz V/V V/μs 7/28 Electrical characteristics Symbol en THD+N Parameter TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Conditions Equivalent input noise voltage f = 10 kHz, Top = 25 °C Total harmonic distortion G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 2.8 Vpp, Top = 25 °C Notes: (1) Guaranteed by design 8/28 DocID12833 Rev 11 Min. Typ. Max. Unit 21 nV/√Hz 0.0018 % TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Electrical characteristics Table 5: Electrical characteristics at VCC+ = 5 V, VCC- = 0 V, Vicm = VCC/2, and RL connected to VCC/2, full temperature range (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA ∆Vio/∆T Top = 25 °C Tmin < Top < Tmax 7.5 Top = 25 °C 1.5 Tmin < Top < Tmax Top = 25 °C Iib Input bias current, (1) (Vout = VCC/2) Top = 25 °C Common mode rejection ratio, 20 log (ΔVic/ΔVio) SVR Supply voltage rejection ratio, 20 log (ΔVcc/ΔVio) Avd Large signal voltage gain VCC VOH VOL High level output voltage Low level output voltage Isink Iout Isource ICC Supply current (per channel) μV/°C 2 Input offset current, (1) (Vout = VCC/2) CMR 3 Input offset voltage drift Iio 1 Tmin < Top < Tmax 10 100 1 Tmin < Top < Tmax 10 pA 100 0 V to 5 V, Vout = 2.5 V, Top = 25 °C 62 Tmin < Top < Tmax 57 VCC = 2.5 to 5 V 70 86 RL= 10 kΩ, Vout = 0.5 V to 4.5 V, Top = 25 °C 80 91 Tmin < Top < Tmax 75 82 dB RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 kΩ, Tmin < Top < Tmax 45 150 Vo = 5 V, Top = 25 °C 18 Tmin < Top < Tmax 16 Vo = 0 V, Top = 25 °C 18 Tmin < Top < Tmax 16 No load, Vout = 2.5 V, Tmin < Top < Tmax mV mV 32 35 0.82 mA 1.1 AC performance GBP Gain Gain bandwidth product Minimum gain for stability RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25 °C 20 Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, positive gain configuration 4 Phase margin = 45 °, Rf = 10 kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25 °C, negative gain configuration -3 DocID12833 Rev 11 MHz V/V 9/28 Electrical characteristics Symbol Parameter TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Conditions Typ. Max. Unit SR Slew rate RL = 2 kΩ, CL = 100 pF, Top = 25 °C 10 V/μs en Equivalent input noise voltage f = 10 kHz, Top = 25 °C 21 nV/√Hz Total harmonic distortion G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 4.4 Vpp, Top = 25 °C 0.0014 % THD+N Notes: (1) Min. Guaranteed by design 10/28 DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Figure 1: Input offset voltage distribution at T = 25 ° C Figure 2: Input offset voltage distribution at T = 125 ° C 40 140 Vcc=5V V icm=2.5V T amb=25°C 120 ° 30 100 Qu an tity of pa rts Qu an tity of pa rts Electrical characteristics 80 60 40 20 10 20 0 -5 -4 -3 -2 -1 0 1 2 3 4 5 0 -5 Inpu t o ffs et V o ltag e (m V ) -4 -3 -2 -1 0 1 2 3 4 5 Inpu t o ffs et V o ltag e (m V ) Figure 3: Supply current vs. input common mode voltage at VCC = 2.5 V Figure 4: Supply current vs. input common mode voltage at VCC = 5 V Figure 5: Output current vs. output voltage at VCC = 2.5 V Figure 6: Output current vs. output voltage at VCC = 5 V DocID12833 Rev 11 11/28 Electrical characteristics TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Figure 8: Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 2.5 V Phase (° ) Phase (°) Figure 7: Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 0.5 V Figure 10: Negative slew rate Figure 9: Positive slew rate V in : from 0.5V to Vcc-0.5V S R : calculated from 10% to 90% V in : from 0.5V to Vcc-0.5V S R : calculated from 10% to 90% Figure 11: Distortion + noise vs. frequency 12/28 Figure 12: Distortion + noise vs. output voltage DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Figure 13: Noise vs. frequency Electrical characteristics Figure 14: Supply current vs. supply voltage DocID12833 Rev 11 13/28 Application information TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 3 Application information 3.1 Driving resistive and capacitive loads These products are low-voltage, low-power operational amplifiers optimized to drive rather large resistive loads above 2 kΩ. TSV99x products are not unity gain stable. To ensure proper stability they must be used in a gain configuration, with a minimum gain of -3 or 4. However, they can be used in a “follower“ configuration by adding a small, in-series resistor at the output, which drastically improves the stability of the device (Figure 15 shows the recommended in-series resistor values). Once the in-series resistor value has been selected, the stability of the circuit should be tested on the bench and simulated with the simulation model. Another way to improve stability and reduce peaking is to add a capacitor in parallel with the feedback resistor. As shown in Figure 16, the feedback capacitor drastically reduces the peaking versus capacitive load (inverting gain configuration, gain = -2). Figure 15: In-series resistor vs. capacitive load when TSV99x is used in follower configuration 3.2 Figure 16: Peaking versus capacitive load, with or without feedback capacitor in inverting gain configuration PCB layouts For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible to the power supply pins. 3.3 Macromodel An accurate macromodel of the TSV99x is available on STMicroelectronics’ web site at www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the TSV99x operational amplifiers. It emulates the nominal performances of a typical device within the specified operating conditions mentioned in the datasheet. It helps to validate a design approach and to select the right operational amplifier, however, it does not replace on-board measurements. 14/28 DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 4 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ® ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ECOPACK is an ST trademark. DocID12833 Rev 11 15/28 Package information 4.1 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A SOT23-5 package information Figure 17: SOT23-5 package outline Table 6: SOT23-5 mechanical data Dimensions Millimeters Ref. A Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 16/28 Inches 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.014 0.016 0.020 C 0.09 0.15 0.20 0.004 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.80 3.00 0.102 0.110 0.118 F 1.50 1.60 1.75 0.059 0.063 0.069 L 0.10 0.35 0.60 0.004 0.014 0.024 K 0 degrees 10 degrees 0 degrees DocID12833 Rev 11 10 degrees TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 4.2 Package information DFN8 2 x 2 (NB) package information Figure 18: DFN8 2 x 2 mm (NB) package outline Table 7: DFN8 2 x 2 x 0.6 mm (NB) mechanical data (pitch 0.5 mm) Dimensions Ref. A Millimeters Inches Min. Typ. Max. Min. Typ. Max. 0.51 0.55 0.60 0.020 0.022 0.024 A1 0.05 A3 0.002 0.15 0.006 b 0.18 0.25 0.30 0.007 0.010 0.012 D 1.85 2.00 2.15 0.073 0.079 0.085 D2 1.45 1.60 1.70 0.057 0.063 0.067 E 1.85 2.00 2.15 0.073 0.079 0.085 E2 0.75 0.90 1.00 0.030 0.035 0.039 e 0.50 0.020 L 0.425 0.017 ddd 0.08 0.003 DocID12833 Rev 11 17/28 Package information TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Figure 19: DFN8 2 x 2 mm (NB) recommended footprint 18/28 DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 4.3 Package information DFN6 1.3 x 1.6 x 0.55 (NA - option 2) package information Figure 20: DFN6 1.3 x 1.6 x 0.55 package outline DocID12833 Rev 11 19/28 Package information TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Table 8: DFN6 1.3 x 1.6 x 0.55 mechanical data Dimensions Ref. Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 0.50 0.55 0.60 0.020 0.022 0.024 A1 0.00 0.02 0.05 0.000 0.001 0.002 A3 B 0.15 0.15 0.20 0.006 0.25 0.006 0.008 D 1.30 0.051 E 1.60 0.063 e 0.40 0.016 L 0.453 0.553 0.653 0.018 0.022 N 6 0.236 aaa 0.05 0.002 bbb 0.07 0.003 ccc 0.10 0.004 ddd 0.05 0.002 eee 0.08 0.003 Figure 21: DFN6 1.3 x 1.6 x 0.55 recommended footprint 20/28 DocID12833 Rev 11 0.010 0.026 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 4.4 Package information MiniSO8 package information Figure 22: MiniSO8 package outline Table 9: MiniSO8 mechanical data Dimensions Millimeters Ref. Min. Typ. A Inches Max. Min. Typ. 1.1 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.026 0.80 0.016 0.024 L1 0.95 0.037 L2 0.25 0.010 k ccc 0° 0.037 8° 0.10 DocID12833 Rev 11 0° 0.031 8° 0.004 21/28 Package information 4.5 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A SO8 package information Figure 23: SO8 package outline Table 10: SO8 mechanical data Dimensions Millimeters Ref. Min. Typ. A Max. Min. Typ. 1.75 0.25 Max. 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 0.004 0.010 0.049 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k ccc 22/28 Inches 1.04 1° 0.040 8° 0.10 DocID12833 Rev 11 1° 8° 0.004 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 4.6 Package information SO14 package information Figure 24: SO14 package outline Table 11: SO14 mechanical data Dimensions Millimeters Ref. Min. Typ. Inches Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.27 0.015 0.05 k ddd 8° (max) 0.10 DocID12833 Rev 11 0.004 23/28 Package information 4.7 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A TSSOP14 package information Figure 25: TSSOP14 package outline Table 12: TSSOP14 mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b c Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 0.09 0.20 0.004 0.0089 1.00 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.176 e L 0.65 0.45 L1 k aaa 24/28 Inches 0.60 0.0256 0.75 0.018 1.00 0° 0.024 0.030 0.039 8° 0.10 DocID12833 Rev 11 0° 8° 0.004 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A 5 Ordering information Ordering information Table 13: Order codes Order code Temperature range TSV991ILT TSV991IQ2T TSV992IST -40 °C to 125 °C TSV992AIST TSV992IDT TSV994IPT K5 K132 MiniSO8 K135 V992I V992AI V994I V994AI Tape and reel TSV994IDT SO14 TSV994AIDT (1) TSV991AIYLT SOT23-5 (1) (1) TSV992AIYDT SO8 (1) (1) TSV992AIYST (1) -40 °C to 125 °C automotive grade MiniSO8 (1) TSV994AIYDT TSV994IYPT K1E TSSOP14 TSV994AIPT TSV994IYDT K1F SO8 TSV992AIDT TSV992IYST K129 DFN6 1.3x1.6x0.55 TSV991AIQ1T (1) SO14 (1) TSV994AIYPT (1) TSSOP14 Marking K130 DFN8 2x2 TSV991AIQ2T TSV992IYDT Packing SOT23-5 TSV991AILT TSV991IYLT Package V994I V994AI K149 K150 V992IY V992AY K149 K150 V994IY V994AY V994IY V994AY Notes: (1) Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. In the table above, all packages except the SO14 are "moisture sensitivity level 1" as per Jedec J-STD-020-C. SO14 is Jedec level 3. DocID12833 Rev 11 25/28 Revision history 6 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Revision history Table 14: Document revision history Date Revision 31-Jul-2006 1 Preliminary data release for product under development. 07-Nov-2006 2 Final version of datasheet. 12-Dec-2006 3 Noise and distortion figures added. 4 ESD tolerance modified for SO14, CDM in Table 1: "Absolute maximum ratings (AMR)". Automotive grade commercial products added in Table 13: "Order codes". Note about SO14 added in Table 13: "Order codes". Limits in temperature added in Section 2: "Electrical characteristics". 5 Corrected MiniSO8 package information. Corrected footnote for automotive grade order codes in order code table. Improved presentation of package information. 6 Added input current information in table Table 1: "Absolute maximum ratings (AMR)". Added Section 3: "Application information". Updated all packages in Section 4: "Package information" . Added new order codes: TSV991IYLT, TSV991AIYLT, TSV992IYST, TSV992AIYST, TSV994IYPT, TSV994AIYPT in Table 13: "Order codes". 7 Added A versions of devices in title on cover page. Added parameters for full temperature range in Table 3, Table 4, and Table 5. Removed gain margin and phase margin parameters in Table 3, Table 4, and Table 5. These parameters have been replaced by the gain parameter (minimum gain for stability). Added Figure 14 and Figure 16. 8 Added parameters for full temperature range in Table 3, Table 4, and Table 5. Modified note relative to automotive grade in Table 13: "Order codes". 9 Document status changed to production data. Modified gain value in Features and Description. Added DFN8 2x2 pin connection diagram. Table 1: "Absolute maximum ratings (AMR)": added package DFN8 2x2 to rows Rthja and ESD. Table 3, Table 4, and Table 5: replaced “DVio” with ΔVio/ΔT; modified “Gain” and “THD+N” conditions and typical values. Figure 7 and Figure 8: added arrows indicating “Gain” and ‘Phase”. 07-Jun-2007 11-Feb-2008 25-May-2009 19-Oct-2009 14-Jan-2010 22-Oct-2012 26/28 Changes DocID12833 Rev 11 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A Date Revision Revision history Changes 22-Oct-2012 9 cont’d Figure 11 and Figure 12: updated. Added Figure 18: "DFN8 2 x 2 mm (NB) package outline" and Figure 19: "DFN8 2 x 2 mm (NB) recommended footprint". Table 13: "Order codes": updated automotive grade qualification and added order code of DFN8 package. 10-Mar-2014 10 Table 13: "Order codes": added new commercial product TSV991AIQ2T; corrected “Marking” error for TSV991IQ2T from K1E to K1F. 11 Added DFN6 1.3 x 1.6 x 0.55 package for new order code TSV991AIQ1T. Updated "L" dimension of Section 4.2: "DFN8 2 x 2 (NB) package information" Updated min "k" value of Section 4.5: "SO8 package information" 12-Jun-2015 DocID12833 Rev 11 27/28 TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 28/28 DocID12833 Rev 11