DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 1/10 2015-06-17 Certificate Holder Everlight Electronics Co., Ltd. No.6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860 Taiwan Manufacturer Everlight Electronics Co., Ltd. No.6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860 Taiwan Production site Certified Product Model Trademark Rated Voltage / Frequency Rated Current / Power Insulation Class Degree of protection (IP) Tested acc. to Test Report No. Additional Expire date Certification Manager Jan-Erik Storgaard Certification Body Everlight Electronics (China) Co., Ltd. No. 2135 Zhong Shan North Rd. Wujiang Economy Development Zone (Yun Xi Area), Songling Town, Wujiang City, Jiang Su China Optocouplers See Page 2 to Page 9 EVERLIGHT 250Vrms EN 60065:2002/A11:2008, EN 60065:2002/A12:2011, EN 60065:2002/A1:2006, EN 60065:2002/A2:2010, EN 60065:2002, EN 60950-1:2006/A11:2009, EN 60950-1:2006/A12:2011, EN 60950-1:2006/A1:2010, EN 60950-1:2006/A2:2013, EN 60950-1:2006, EN 61347-1:2008/A1:2011, EN 61347-1:2008/A2:2013 EN 61347-1:2008, EN 60335-1:2012/A11:2014, EN 60335-1:2012, EN 62368-1:2014 P15219385 issued on 2015-02-09 This is to replace previous certificate No. D-03294 issued on 2014-04-24, D-03295-M1 issued on 2014-04-30, D-03296 issued on 2014-04-24 and D-03301-M1 issued on 2014-04-30 due to new test report has been issued 2025-06-16 This is to certify that representative sample(s) of the Product described herein (“Certified Product”) have been investigated and found in compliance with the Standard(s) indicated on this Certificate, in accordance with the D Mark Requirements. The Designated Certificate holder is entitled to use the δ or for cables <DEMKO> > for the Certified Product manufactured at the production site(s) identified above, in accordance with the D Mark Service Agreement, including without limitation the D Mark Testing and Certification Services Service Terms. Only those Products bearing the D Mark should be considered as being covered by UL’s D Mark Service. This Certificate shall remain valid through the expiration date, unless terminated earlier in accordance with the Service Agreement including without limitation if the Standard identified on this Certificate is amended or withdrawn prior the expiration date. UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 2/10 2015-06-17 Model / Type Ref. EL817./EL816./EL819./EL829./EL826./EL827./ EL717./4N25./4N26./4N27./4N28./4N35./4N36./4N37./4N38./MCT2./MCT2E./ MCT210./CNY17-1./CNY17-2./CNY17-3./CNY17-4./MOC8111./MOC8112./ MOC8113./H11A1./H11A2./H11A3./H11A4./H11A5./TIL111./TIL117/CNX35U. Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110ºC.Tested for 5000m. Model / Type Ref. EL451./EL452. Optocoupler. Minimum external creepage distance is measured to 5.0mm, minimum internal creepage distance is measured to 4.0mm and minimum distance through insulation is measured to 0.4mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110°C. The symbol “X” in type denotes X = Part no. (0,1,2,3,4). Model / Type Ref. ELD3H5./ ELD3H6./ ELD3H7./ ELD3H4./ ELQ3H4./ ELQ3H5./ ELQ3H7./ ELM314. Optocoupler. Minimum external creepage distance is measured to 5.0mm, minimum internal creepage distance is measured to 4.0mm and minimum distance through insulation is measured to 0.4mm. Tested for reinforced insulation. Maximum operating temperature: 110°C. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 3/10 2015-06-17 Model / Type Ref. ELM452./ ELM453./ ELM600./ ELM601./ ELM611./ ELM452L./ ELM453L./ ELM600L./ ELM601L./ ELM611L./ELM454. High Speed Optocoupler. Minimum external creepage distance is measured to 5.0mm, minimum internal creepage distance is measured to 4.0mm and minimum distance through insulation is measured to 0.4mm. Tested for reinforced insulation. Maximum operating temperature: 100°C. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Model / Type Ref. ELD851./ELD852./4N29./4N30./4N31./4N32./4N33./H11B1./H11B2./H11B3./ H11B255./TIL113./MOC119./MOC8020./MOC8021./MOC8030./MOC8050./ MOC8080./EL301X./EL302X./EL305X./EL307X./EL303X./EL304X./EL306X./ EL308X./EL3161./EL3162./EL3163./H11L1./H11L2. Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C. The symbol “X” in type denotes X = Part no. (0,1,2,3,4). Model / Type Ref. ELR3602./ELR3603./ELR2602./ELR2603./ELR1602./ELR1603./ELR3502./ ELR3503./ELR2502./ELR2503./ELR1502./ELR1503. Power Triac Optocoupler. Minimum external creepage distance is measured to 8.2mm, minimum internal creepage distance is measured to 5.1mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength tests, between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 4/10 2015-06-17 Model / Type Ref. EL2801./EL354./EL355./EL356./EL357./EL359./EL121./EL124./EL2701./ EL2705./EL357N./EL356N./EL121N./EL124N./EL2701N./EL354N./ EL2705N./EL3H7./EL281./EL3H4./EL280./EL3H71./ELM301X./ELM302X./ ELM305X./ELM307X./ELM303X./ELM304X./ELM306X./ELM308X. Optocoupler. Minimum external creepage distance is measured to 5.0mm, minimum internal creepage distance is measured to 4.0mm and minimum distance through insulation is measured to 0.4mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110°C. The symbol “X” in type denotes X = Part no. (0,1,2,3,4). Model / Type Ref. EL847./EL844./EL845. Optocoupler. Minimum external creepage distance is measured to 8.0mm, minimum internal creepage distance is measured to 5.1mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength tests, between input and output 4800Vac/1 minute. The symbol "." in type designation may be A to Z, numbers or blank, denote different pin shape. Maximum operating temperature: 110°C Model / Type Ref. EL815./ EL814./EL824./ EL825. Optocoupler. Minimum external creepage distance is measured to 7.9mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110º Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 5/10 2015-06-17 Model / Type Ref. EL101X./ EL357L./ EL355L./ EL354L./ EL111X./ EL161X./ EL151X. Optocoupler. Minimum external creepage distance is measured to 8.1mm, minimum internal creepage distance is measured to 5.2mm and minimum distance through insulation is measured to 0.4mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110°C. The symbol “X” in type denotes X = Part no. (0,1,2,3,4,5,6,7,8,9).Tested for 5000m. Model / Type Ref. EL205./EL206./EL207./EL208./EL211./EL212./EL213./EL215./EL216./ EL217./ELD207./ELD208./ELD213./ELD217./ELD205./ELD206./ELD211. Optocoupler. Minimum external creepage distance is measured to 4.4mm, minimum internal creepage distance is measured to 3.5mm and minimum distance through insulation is measured to 0.4mm. Tested for basic and supplementary insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 2400Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110°C Model / Type Ref. 6N135./6N136./6N137./6N138./6N139./EL2502./EL250L./EL2503./EL4502./ EL4503./EL2530./EL253L./EL2531./EL4534./EL2730./EL2731./EL2601./ EL260L./EL2611./EL261A./EL261N./EL2630./EL263L./EL263A./EL263N./ EL2631./EL4661./EL4504. High Speed Optocoupler. Minimum external creepage distance is measured to 8.0mm, minimum internal creepage distance is measured to 5.0mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C. Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 6/10 2015-06-17 Model / Type Ref. H11L3./H11D1./H11D2./H11D3./H11D4./H11G1./H11G2./EL371./ EL725./4N50./4N51./4N52./4N53./4N54./4N55./4N56./4N57./4N58./4N59./ EL852./EL851./H11G3. Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C. The symbol “X” in type denotes X = Part no. (0,1,2,3,4). Model / Type Ref. EL0500./EL0501./EL0452./EL0453./EL0454./EL0600./EL0601./EL0611./ EL0700./EL050L./EL060L./EL0701./EL061A./EL061N./EL0551./EL0530./ EL0531./EL0533./EL063X./EL0661./EL0730./EL0731./EL053L. High Speed Optocoupler . Minimum external creepage distance is measured to 4.4mm, minimum internal creepage distance is measured to 3.5mm and minimum distance through insulation is measured to 0.4mm. Tested for basic and supplementary insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 2400Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C. The symbol “X” in type denotes X = Part no. (0,1,L,A,N). Model / Type Ref. EL617./CNY75G./CQY80.G/K233.G/TCDT110.G/TCDT111.G/TCDT112.G/ HS817.G/TCET110.G/TCET111.G/ TCET120.G Optocoupler. Minimum external creepage distance is measured to 8.0mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110°C Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 7/10 2015-06-17 Model / Type Ref. EL2200./EL2212./EL2231./EL2201./EL2202./EL2219./EL2211./ EL2232. High Speed Optocoupler. Minimum external creepage distance is measured to 8.2mm, minimum internal creepage distance is measured to 5.1mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength tests, between input and output 4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 100°C Model / Type Ref. CNX36U./CNX38U./CNX39U./SL5500./SL5501./SL5504./SL5511./ MOC8100./MOC8101./MOC8102./MOC8103./MOC8104./MOC8105./ MOC8106./MOC8107./MOC8108./EL9001./CNY17F-1./CNY17F-2./ CNY17F-3./CNY17F-4./H11AA1./H11AA2./H11AA3./H11AA4./HS817./ K817P./TCET110. Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110ºC.Tested for 5000m. Model / Type Ref. TCET111./TCET120./VO610A./VO615A./CNY17G./CNY75./CQY80./K233./ TCDT110./TCDT111./TCDT112./EL2501./EL2561./EL8171./CNY171-1./ CNY171-2./CNY171-4./CNY17F1-1./CNY17F1-2./CNY17F1-3./CNY17F1-4./ EL610./CNY1713. Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Maximum operating temperature: 110ºC.Tested for 5000m. Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 8/10 2015-06-17 Model / Type Ref. EL806A./ EL810A./ EL820A./ EL825A./ EL835A./ EL840A./ EL860A./ EL406A./ EL410A./ EL420A./ EL425A./ EL435A./ EL440A./ EL460A./ EL606A./ EL610A./ EL620A./ EL625A./ EL635A./ EL640A./ EL660A. Solid State Relay. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Maximum operating temperature: 85ºC. Thermal cycling test, 10 cycles. Each cycle: 68h in 85 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Model / Type Ref. ELT301X./ ELT302X./ ELT305X./ ELT303X./ ELT304X./ ELT306X./ ELT308X./ ELT307X. Triac Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Maximum operating temperature: 110ºC. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol “X” in type denotes X = Part no. (0,1,2,3,4). The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Model / Type Ref. ELW137./ ELW139./ ELW2601./ ELW2611./ ELW136./ ELW135./ ELW4502./ ELW4503./ ELW138./ ELW260L./ ELW250L./ ELW4504. High Speed Optocoupler. Minimum external creepage distance is measured to 11.85mm, minimum internal creepage distance is measured to 7.72mm and minimum distance through insulation is measured to 0.9mm. Tested for reinforced insulation. Maximum operating temperature: 100°C. Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue D-04274 9/10 2015-06-17 Model / Type Ref. EL3120./ EL3140./ EL3150./ EL3180./ EL3184. IGBT Gate Drive Optocoupler. Minimum external creepage distance is measured to 7.7mm, minimum internal creepage distance is measured to 6.0mm and minimum distance through insulation is measured to 0.5mm. Tested for reinforced insulation. Maximum operating temperature: 110ºC. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. Model / Type Ref. ELW3120./ ELW3140./ ELW3150./ ELW3180./ ELW3184. IGBT Gate Drive Optocoupler. Minimum external creepage distance is measured to 11.85mm, minimum internal creepage distance is measured to 7.72mm and minimum distance through insulation is measured to 0.9mm. Tested for reinforced insulation. Maximum operating temperature: 110°C. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for 48h in 93% relative humidity. Electric strength test between input and output 4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z or numbers, and denote different pin shape. External Certification Information: The certificate has been issued on the basis of CB certificate No. P15219385, issued on 2015-02-09 by Nemko AS Certification Body UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com Appendix DEMKO CERTIFICATE Certificate No. Page Date of Issue Certification Body D-04274 10/10 2015-06-17 UL International Demko A/S, Borupvang 5A, DK-2750 Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected] www.ul-europe.com