-100mA/-50V Digital transistors(with built-in resistors) DTA043TM / DTA043TEB / DTA043TUB Dimensions (Unit : mm) Features 1) Built-in input resistor enables the direct control of base terminal by input voltage without external resistor. (See Inner circuit) 2) The bias resistors consist of thin-film resistors with complete isolation to allow positive biasing of the input. They also have the advantage of almost completely eliminating parasitic effects. 3) Only the on/off conditions need to be set for operation, making the device design easy. VMT3 Abbreviated symbol : 39 EMT3F (3) (1) Structure PNP epitaxial planar silicon transistor (Resistor built-in type) (2) Abbreviated symbol : 39 UMT3F 2.0 0.9 0.53 (1) 0.53 0.425 Applications Inverter, Interface, Driver (3) 1.25 2.1 0.425 0.32 (2) 0.13 0.65 0.65 1.3 Abbreviated symbol : 39 Packaging specifications Package Packaging Type Type Code Basic ordering unit (pieces) DTA043ＴM DTA043ＴEB DTA043ＴUB Inner circuit VMT3 Taping T2L EMT3F Taping TL UMT3F Taping TL 8000 3000 3000 ○ - ○ - ○ C R1 B B : Base C : Collector E : Emitter E R1=4.7kΩ Absolute maximum (Ta=25C) Parameter Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current Power dissipation Junction temperature Range of storage temperature Symbol Limits(DTA043T□) M VCBO VCEO VEBO IC(max) PD Tｊ Tstg EB UB -50 -50 -5 -100 150 200 150 -55 to +150 Unit V V mA mA mW * C C * Each terminal mounted on a recommended land www.rohm.com ©2010 ROHM Co., Ltd. All rights reserved. 1/2 2010.09 - Rev.A DTA043TM / DTA043TEB / DTA043TUB Data Sheet Electrical characteristics (Ta=25C) Parameter Symbol Min. Typ. Collector-Base breakdown voltage BVCBO -50 - - V Collector-Emitter breakdown voltage BVCEO -50 - - V IC=-1mA Emitter-Base breakdown voltage Collector cut-off current Emitter cut-off current Collector-Emitter saturation voltage DC current gain Max. Test Conditions Unit IC=-50uA BVCEO -5 - - V IE=-50uA ICBO - - -500 nA VCB=-50V IEBO - - -500 nA VEB=-4V VCE(sat) - -0.07 -0.15 V IC=-5mA / IB=-0.5mA hFE 100 - 600 - VCE=-10V / IC=-0.5mA Transition frequency * fT - 250 - MHz Input resistance R1 3.29 4.7 6.11 kΩ VCE=-10V / IC=-5mA f=100MHz * Characteristics of built-in transistor Electrical characteristics curves -1 1000 100 COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) DC CURRENT GAIN : hFE VCE=-10.0V Ta=125℃ Ta=75℃ Ta=25℃ Ta=-40℃ 10 1 -0.1 -1 -10 COLLECTOR CURRENT : IC (mA) www.rohm.com ©2010 ROHM Co., Ltd. All rights reserved. -0.1 -0.01 -0.001 -0.1 -100 Fig.1 DC Current Gain vs. Collector Current IC/IB=10 Ta=125℃ Ta=75℃ Ta=25℃ Ta=-40℃ -1 -10 -100 COLLECTOR CURRNET : IC (mA) Fig.2 Collector Saturation Voltage vs. Collector Current 2/2 2010.09 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A