THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ABSOLUTE MAXIMUM RATINGS PARAMETER TABLE 1.0 UNITS MINIMUM NOMINAL MAXIMUM -55 - 125 °C Supply Voltage (Vcc) -0.5 - 4.6 Vdc Control Voltage (Vc) -0.5 - Vcc+0.5 Vdc MINIMUM NOMINAL MAXIMUM UNITS (Fo) 20 - 200 MHz 0 - 70 °C Supply Voltage (Vcc) 3.135 3.3 3.465 Vdc Supply Current (Icc) Storage Temperature UNITS OPERATING SPECIFICATIONS Operating Temperature Range - - 100 mA Period Jitter RMS - 3 5 ps rms Integrated Phase Jitter (BW=12kHz to 20MHz) - 0.3 1.0 ps rms SSB Phase Noise at 10Hz offset - -60 - dBc/Hz SSB Phase Noise at 100Hz offset - -90 - dBc/Hz SSB Phase Noise at 1KHz offset - -120 - dBc/Hz SSB Phase Noise at 10KHz offset - -140 - dBc/Hz SSB Phase Noise at 100KHz offset - -145 - dBc/Hz MINIMUM NOMINAL MAXIMUM UNITS 0.3 1.65 3.0 Vdc NOTE Typical Phase Noise for 155.52MHz INPUT CHARACTERISTICS TABLE 3.0 PARAMETER Control Voltage Range (Vc) Typical Slope (Fo = 155.52MHz) - 75 - ppm/V ±50 - - ppm Monotonic Linearity -10 - 10 % DC Input Resistance (Pad 1) - 60K - Ohm Modulation Bandwidth (3dB) 25 - - KHz 1.68 Vdc 2 - Vdc 2 (Vil) - Disable Input Voltage (High) (Vih) 2.275 LVPECL OUTPUT CHARACTERISTICS NOMINAL MAXIMUM UNITS NOTE 3 - - 50 Ohms (High) (Voh) 2.275 - - Vdc (Low) (Vol) - - 1.68 Vdc 45 50 55 % - 0.6 1.5 ns Duty Cycle at 50% Level Rise / Fall Time 20% to 80% PACKAGE CHARACTERISTICS CW 3.3V OPERATION LOW JITTER <1pS RMS ABSOLUTE PULL RANGE (APR): ±50ppm TEMPERATURE RANGE: 0 to 70°C DIFFERENTIAL LVPECL OUTPUTS ENABLE / DISABLE FUNCTION TABLE 5.0 Hermetically sealed ceramic package with grounded metal cover RoHS compliant / lead free, see solder profile on page 2. Package Soldering Process FEATURES 20 to 200 MHz MINIMUM LOAD Voltage 1 TABLE 4.0 PARAMETER The Connor-Winfield V702 is a 3.3V Voltage Controlled Crystal Oscillator (VCXO) with LVPECL Differential outputs and enable/disable function. The V702 is designed for use with applications utilizing a PLL system requiring low jitter and tight frequency stability. No multiplication schemes are used in this oscillator design. The surface mount package is designed for high-density mounting and is optimum for mass production. NOTE Absolute Pull Range (APR) Enable Input Voltage (Low) V702 DESCRIPTION TABLE 2.0 PARAMETER Center Frequency NOTE 0803 V702 155.52Mhz 3.3V 5 x 7mm SURFACE MOUNT HIGH FREQUENCY LVPECL VCXO OSCILLATOR SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING RoHS COMPLIANT / LEAD FREE ORDERING INFORMATION V7 Type: LVPECL VCXO 5.0x7.0mm Package - 0 2 Temperature Range: APR and Supply Voltage: 0 = 0 to 70° C. 155.52M Output Frequency: Frequency Format -xxx.xM Minimum* -xxx.xxxxxxM Maximum* *Amount of numbers after the decimal point. M = MHz 2 = ± 50 ppm 3.3 Vdc Example: To order an V702 with an output frequency of: 25 MHz = V702-025.0M 44.736 MHz = V702-044.736M 155.52 MHz = V702-155.52M Specifications subject to change without notice. DATA SHEET #: Vx515 PAGE 1 OF 2 REV: 02 DATE: 01/16/08 aCopyright 2008 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Notes 1.0 Absolute pull range (APR) is the minimum guaranteed pull range of the VCXO under all conditions over the lifetime operation. Including calibration @ 25°C, frequency vs. change in temperature, frequency vs. change in supply voltage, frequency vs. change in load, shock and vibration and aging for ten years. The APR is referenced to Fo. Positive Transfer Function. Outputs are enabled with no connection on pad 2. When oscillator is disabled both outputs are in a high impedance state. 50 ohm termination into Vcc-2V or Thevein equivalent. 2.0 3.0 Output Waveform Pad Connections TABLE 6.0 Pad Connection Control Voltage Enable / Disable Ground (Case) Output Q Output Q Vcc Pad 1 2 3 4 5 6 Duty Cycle Q 80% 50% 20% Q Enable / Disable Function Output Enable Function Enable / Disable Function (Pad 2) No Connection Low High tr Suggested Pad Layout Package Outline 7 tf TABLE 7.0 Output Enable Enable Disable (High Impedance) MAX 0 CW MAX 0803 V702 155.52MHZ .070 MAX (1.8mm) Test Circuit Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 120°C 2 Control Voltage E/D 0 120 S Max. Vcc = Vcc2 = 3.3Vdc 10 S Time 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Vx515 PAGE 2 OF 2 REV: 02 DATE: 01/16/08 aCopyright 2008 Connor-Winfield all rights reserved.