UPB1506GV

FEATURES
TEST CIRCUIT
• HIGH FREQUENCY OPERATION TO 3 GHz
UE
• SELECTABLE DIVIDE RATIO: ÷64, ÷128, ÷256
UPB1506GV
UPB1507GV
D
NEC's 3.0 GHz
DIVIDE BY 64/128/256 PRESCALER
UPB1507GV
• LOW CURRENT CONSUMPTION: 19 mA at 5 V
C
C
• SMALL PACKAGE: 8 pin SSOP
• AVAILABLE IN TAPE AND REEL
1 IN
IN
8
2 VCC
NC
7 OPEN
3 SW1
SW2 6
4 OUT
GND 5
fIN
C
IN
VOUT
DESCRIPTION
SC
O
NT
NEC's UPB1506GV and UPB1507GV are Silicon MMIC digital
prescalers manufactured with the NESAT™ IV silicon bipolar
process. They feature high frequency response to 3 GHz,
selectable divide-by-64, 128, or 256 modes, and operate on a
5 volt supply while drawing only 19 mA. The devices are
housed in a small 8 pin SSOP package that contributes to
system miniaturization. These devices are designed for use in
a PLL synthesizer for DBS and CATV settop and WLAN
applications.
VCC
10,000 pF
C = 1000 pF
ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 4.5 to 5.5 V, Zs = 50Ω)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
Circuit Current
mA
fIN(U)
Upper Limit Operating Frequency, PIN = -15 to +6 dBm
GHz
fIN(L)1
Lower Limit Operating Frequency, PIN = -10 to +6 dBm
GHz
DI
ICC
UPB1506GV,UPB1507GV
S08
MIN
12.5
TYP
MAX
19
26.5
3.0
0.5
fIN(L)2
Lower Limit Operating Frequency, PIN = -15 to +6 dBm
GHz
PIN1
Input Power, fIN = 1.0 to 3.0 GHz
dBm
-15
1.0
PIN2
Input Power, fIN = 0.5 to 1.0 GHz
dBm
-10
VOUT
Output Voltage, CL = 0.8 pF
VP-P
1.2
VIN(H)
Division Ratio Control Input High
V
VCC
VIN(L)
Division Ratio Control Input Low
V
OPEN or GND
+6
+6
1.6
California Eastern Laboratories
UPB1506GV, UPB1507GV
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
PARAMETERS
UNITS
RATINGS
RECOMMENDED
OPERATING CONDITIONS
Supply Voltage
V
-0.5 to 6.0
SYMBOL
VIN
Input Voltage
V
-0.5 to Vcc + 0.5
VCC
Supply Voltage
V
4.5
5.0
5.5
PIN
Input Power
dBm
+10
TOP
Operating Temperature
°C
-40
+25
+85
PD
Power Dissipation2
mW
250
TOP
Operating Temperature
°C
-45 to +85
TSTG
Storage Temperature
°C
-55 to +150
UPB1507GV
2
1
IN
3
8
IN
4
5
GND
1
3
SW1
Pin
Voltage
(V)
Description
–
2.9
Signal input pin. This pin should be coupled to the source with a capacitor
(eg 1000 pF).
–
2.9
Signal input bypass pin. This pin must be equipped with a bypass
capacitor (eg 1000 pF) to ground.
0
–
Ground pin. Ground pattern on the board should be formed as wide as
possible to minimize ground impedance.
H/L
–
Divided ratio input pin. The ratio can be controlled by the following input
data to these pins.
SC
O
UPB1506GV
Applied
Voltage
(V)
IN
Pin
Name
NT
Pin No.
6
6
SW2
8
2
VCC
4.5 to 5.5
7
4
OUT
–
2.6 to 4.7
5
7
NC
–
–
DI
UNITS MIN TYP MAX
UE
Notes:
1. Operation in excess of any one of these parameters may result
in permanent damage.
2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy
glass PWB (TA = +85˚C).
PIN DESCRIPTIONS
PARAMETER
D
VCC
–
SW2
H
L
H
÷64
÷128
L
÷128
÷256
SW1
These pins should be equipped with a bypass capacitor (e.g. 1000 pF) to
ground.
Power supply pin. This pin must be equipped with bypass capacitor
(eg 1000 pF) to ground.
Divided frequency output pin. This pin is designed as an emitter follower
output. This pin can be connected to CMOS input due to 1.2 Vp-p MIN
output.
No connection. This pin must be opened.
UPB1506GV, UPB1507GV
TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted)
CURRENT vs.
VOLTAGE and TEMPERATURE
+20
No Signals
TA = +25°C
VCC = 4.5 to 5.5 V
Guaranteed
Operating
Window
0
-10
-20
UE
15
D
TA = +85°C
20
TA = +25°C
+10
Input Power, PIN (dBm)
Circuit Current, ICC (mA)
25
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
TA = -40°C
10
5
-30
VCC = 4.5 to 5.5 V
-40
-50
0
-60
0
1
2
3
4
5
100
6
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Output Voltage, VOUT (VPP)
-20
TA = +85°C
TA = +25°C
-40
TA = -40°C
VCC = 5.5 V
1.7
VCC = 5.0 V
1.6
1.5
VCC = 4.5 V
1.4
1.2
-60
1000
1.8
1.3
-50
100
TA = +25°C
PIN = -10 dBm
NT
-10
SC
O
Input Power, PIN (dBm)
Guaranteed
Operating
Window
TA = +85°C
-30
1.9
TA = +25°C
TA = -40°C
0
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
2.0
VCC = 4.5 to 5.5 V
+10
100
4000
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
2.0
1.6
1.4
VCC = 5.0 V
1.2
VCC = 4.5 V
1.0
0.8
0.6
1.8
Output Voltage, VOUT (VPP)
VCC = 5.5 V
4000
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
TA = -40°C
PIN = -10 dBm
DI
Output Voltage, VOUT (VPP)
1.8
1000
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
2.0
4000
IN
Supply Voltage, VCC (V)
+20
1000
Input Frequency, fin (MHz)
TA = +85°C
PIN = -10 dBm
VCC = 5.5 V
VCC = 5.0 V
1.6
1.4
VCC = 4.5 V
1.2
1.0
0.8
0.6
0.4
0.4
100
1000
Input Frequency, fin (MHz)
4000
100
1000
Input Frequency, fin (MHz)
4000
UPB1506GV, UPB1507GV
TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
+20
TA = +25°C
VCC = 4.5 to 5.5 V
TA = -40°C
Guaranteed
Operating
Window
0
Input Power, PIN (dBm)
0
-10
-30
VCC = 4.5 to 5.5 V
-40
-10
-20
-30
TA = +85°C
TA = +25°C
TA = -40°C
-40
-50
-60
100
1000
-60
4000
100
VCC = 5.5 V
VCC = 5.0 V
1.6
1.5
VCC = 4.5 V
1.4
SC
O
1.3
1000
1.8
1.7
VCC = 5.5 V
1.6
VCC = 5.0 V
1.5
VCC = 4.5 V
1.4
1.3
1.2
1.2
100
TA = -40°C
PIN = -10 dBm
NT
1.9
1.8
1.7
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
2.0
TA = +25°C
PIN = -10 dBm
1.9
100
4000
VCC = 5.5 V
1.6
VCC = 5.0 V
1.5
VCC = 4.5 V
1.4
1.3
TA = +25°C
+10
Input Power, PIN (dBm)
DI
Output Voltage, VOUT (VPP)
+20
TA = +85°C
PIN = -10 dBm
1.7
4000
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
1.8
1000
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
1.9
4000
Input Frequency, fin (MHz)
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
2.0
1000
IN
Input Frequency, fin (MHz)
2.0
TA = +25°C
Guaranteed
Operating
Window
TA = +85°C
UE
-20
-50
Output Voltage, VOUT (VPP)
VCC = 4.5 to 5.5 V
+10
Output Voltage, VOUT (VPP)
Input Power, PIN (dBm)
+10
D
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
VCC = 4.5 to 5.5 V
0
Guaranteed
Operating
Window
-10
-20
-30
VCC = 4.5 to 5.5 V
-40
-50
1.2
100
1000
Input Frequency, fin (MHz)
4000
-60
100
1000
Input Frequency, fin (MHz)
4000
UPB1506GV, UPB1507GV
TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted)
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
2.0
+20
Output Voltage, VOUT (VPP)
Guaranteed
Operating
Window
TA = +85°C
TA = +25°C
-10
-30
TA = +85°C
TA = +25°C
-40
1.8
VCC = 5.5 V
1.7
1.6
VCC = 5.0 V
UE
-20
TA = -40°C
-50
1.5
VCC = 4.5 V
1.4
1.3
1.2
-60
100
1000
100
4000
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
OUTPUT VOLTAGE vs.
INPUT FREQUENCY and VOLTAGE
2.0
TA = -40°C
PIN = -10 dBm
1.9
1.6
VCC = 5.5 V
1.4
VCC = 5.0 V
1.2
1.0
VCC = 4.5 V
SC
O
0.8
0.6
0.4
100
1000
Input Frequency, fin (MHz)
DI
TA = +85°C
PIN = -10 dBm
NT
1.8
4000
IN
Input Frequency, fin (MHz)
2.0
1000
Input Frequency, fin (MHz)
4000
Output Voltage, VOUT (VPP)
Input Power, PIN (dBm)
TA = -40°C
0
D
1.9
+10
Output Voltage, VOUT (VPP)
TA = +25°C
PIN = -10 dBm
VCC = 4.5 to 5.5 V
1.8
VCC = 5.5 V
1.7
VCC = 5.0 V
1.6
1.5
VCC = 4.5 V
1.4
1.3
1.2
100
1000
Input Frequency, fin (MHz)
4000
UPB1506GV, UPB1507GV
TYPICAL SCATTERING PARAMETERS (TA = 25°C)
UPB1506GV
S11 vs. INPUT FREQUENCY
C
D
MARKER 3
2.0 GHZ
1
3
1
: 1.0 GHz
3
: 2.0 GHz
4
: 3.0 GHz
ANG
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
0.868
0.828
0.794
0.761
0.721
0.706
0.662
0.629
0.595
0.554
0.516
0.440
0.428
0.543
0.555
0.560
0.558
0.564
0.570
0.574
0.574
0.564
0.530
0.476
0.411
0.331
-26.6
-32.6
-37.4
-41.9
-46.5
-49.3
-54.0
-57.2
60.2
-62.9
-64.8
-61.9
51.0
-61.5
-68.4
-74.7
- 79.5
-84.9
-90.9
-98.3
-107.9
- 118.3
-131.4
- 144.6
- 159.1
- 175.8
NT
2
2
MAG
IN
4
: 0.5 GHz
GHz
UE
S11
Z
REF 1.0 Units
3
200.0 mUnits/
33.881 Ω -52.875 Ω
hp
START 0.500000000 GHz
STOP 3.000000000 GHz
UPB1506GV
S11
D
FREQUENCY
VCC = 5.0 V
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
SC
O
Divide by 64 mode, VCC = 5.0 V
S22
Z
REF 1.0 Units
1
200.0 mUnits/
171.22 Ω -04.438 Ω
hp
C
1
DI
D
MARKER 1
45.0 MHZ
START 0.045000000 GHz
STOP 0.100000000 GHz
2
1
: 45 MHz
2 : 100 MHz
MHz
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.542
0.602
0.616
0.605
0.609
0.616
0.620
0.622
0.619
0.610
0.626
0.623
-1.4
-0.3
0.0
1.1
0.7
0.3
0.1
0.0
0.6
0.9
-0.7
-1.7
UPB1506GV, UPB1507GV
TYPICAL SCATTERING PARAMETERS (TA = 25°C)
UPB1506GV
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
C
MARKER 1
45.0 MHZ
D
1
: 45 MHz
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.590
0.604
0.610
0.607
0.548
0.630
0.615
0.618
0.617
0.616
0.623
0.624
-0.4
-1.0
-1.1
-0.8
-5.9
-0.0
-1.0
-1.4
-1.2
-2.2
-2.4
-2.3
IN
1
2 : 100 MHz
NT
2
MHz
UE
S22
Z
REF 1.0 Units
1
200.0 mUnits/
192.34 Ω 03.109 Ω
hp
D
Divide by 128 mode, VCC = 5.0 V
START 0.045000000 GHz
STOP 0.100000000 GHz
SC
O
UPB1506GV
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
Divide by 256 mode, VCC = 5.0 V
S22
Z
REF 1.0 Units
1
200.0 mUnits/
199.25 Ω -05.992 Ω
hp
C
MARKER 1
45.0 GHZ
DI
D
START 0.045000000 GHz
STOP 0.100000000 GHz
1
2
1
: 45 MHz
2 : 100 MHz
MHz
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.601
0.609
0.611
0.620
0.607
0.615
0.613
0.611
0.607
0.605
0.610
0.608
-0.9
-1.6
-1.5
-1.4
-2.1
-1.9
-3.2
-2.8
-2.5
-2.4
-3.0
-2.8
UPB1506GV, UPB1507GV
TYPICAL SCATTERING PARAMETERS (TA = 25°C)
UPB1507GV
S11 vs. INPUT FREQUENCY
FREQUENCY
S11
C
D
MARKER 4
3.0 GHZ
1
3
: 0.5 GHz
2
: 1.0 GHz
3
: 2.0 GHz
4
: 3.0 GHz
ANG
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
0.857
0.849
0.800
0.764
0.725
0.665
0.619
0.573
0.531
0.484
0.439
0.377
0.340
0.377
0.441
0.464
0.443
0.466
0.465
0.454
0.433
0.383
0.350
0.332
0.271
0.185
-27.5
-32.0
-38.9
-43.8
-49.0
-50.9
-55.3
-59.3
-61.3
-62.8
-63.0
-59.1
-54.1
-54.7
-59.5
-67.2
-67.4
-74.5
-81.3
-89.4
-99.2
-109.6
-114.0
-124.2
-141.2
-163.6
NT
2
1
MAG
IN
4
GHz
UE
S11
Z
REF 1.0 Units
4
200.0 mUnits/
38.111 Ω 0.9707 Ω
hp
START 0.500000000 GHz
STOP 3.000000000 GHz
SC
O
UPB1507GV
D
VCC = 5.0 V
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
Divide by 64 mode, VCC = 5.0 V
S22
Z
REF 1.0 Units
1
200.0 mUnits/
185.13 Ω 17.789 Ω
hp
C
MARKER 1
45.0 GHZ
DI
D
START 0.045000000 GHz
STOP 0.100000000 GHz
1
1
2
2
: 45 MHz
: 100 MHz
MHz
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.580
0.572
0.574
0.574
0.584
0.587
0.592
0.587
0.589
0.591
0.573
0.604
3.4
2.5
3.0
2.7
3.0
2.6
2.4
2.6
2.9
2.9
1.7
2.9
UPB1506GV, UPB1507GV
TYPICAL SCATTERING PARAMETERS (TA = 25°C)
UPB1507GV
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
C
MARKER 1
45.0 GHZ
D
1
: 45 MHz
1
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.578
0.571
0.572
0.576
0.584
0.587
0.589
0.589
0.588
0.593
0.598
0.602
3.2
2.8
3.3
3.0
3.1
2.8
2.4
2.8
3.0
2.8
3.0
2.9
IN
2
MHz
UE
S22
Z
REF 1.0 Units
1
200.0 mUnits/
185.02 Ω 18.953 Ω
hp
D
Divide by 128 mode, VCC = 5.0 V
NT
2 : 100 MHz
START 0.045000000 GHz
STOP 0.100000000 GHz
SC
O
UPB1507GV
S22 vs. OUTPUT FREQUENCY
FREQUENCY
S22
Divide by 256 mode, VCC = 5.0 V
S22
Z
REF 1.0 Units
4
200.0 mUnits/
186.76 Ω 17.82 Ω
hp
C
MARKER 1
45.0 GHZ
DI
D
START 0.045000000 GHz
STOP 0.100000000 GHz
1
1
2
2
: 45 MHz
: 100 MHz
MHz
MAG
ANG
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
100.0
0.580
0.572
0.571
0.576
0.585
0.590
0.589
0.590
0.588
0.597
0.600
0.601
3.0
2.8
2.9
2.9
3.2
2.8
2.5
2.6
2.9
2.9
3.1
3.1
UPB1506GV, UPB1507GV
SYSTEM APPLICATION EXAMPLE
1stIF input
from DBS converter
MIX
BPF
To 2150 MHz
High Division prescaler
UPB1506GV or
UPB1507GV
FM demo.
CMOS
PLL
synthesizer
IN
OSC
To 2650 MHz
AGC amp.
UE
SAW
D
RF unit block of Analog DBS tuners
LPF
NT
loop filter
SC
O
RF unit block of Analog CATV converter
downconverter
upconverter
To 800 MHz
BPF
OSC
DI
To 2000 MHz
BPF
To 1300 MHz
High Division prescaler
UPB1506GV or
UPB1507GV
LPF
loop filter
CMOS
PLL
synthesizer
UPB1506GV, UPB1507GV
INTERNAL BLOCK DIAGRAM
IN
D Q
CLK
Q
CLK
D Q
CLK
Q
D Q
CLK
Q
D Q
CLK
Q
PACKAGE OUTLINE S08
D Q
CLK
Q
7
8
D Q
CLK
Q
D Q
CLK
Q
D Q
CLK
Q
OUT
6
1509
AMP
Detail of Lead End
N
SW2
UE
SW1
5
D
IN
OUTLINE DIMENSIONS (Units in mm)
1
+7˚
4
2
3
3.0 MAX
3 -3˚
4.94 ± 0.2
+0.10
0.15 -0.05
1.5±0.1
3.2±0.1
1.8 MAX
0.65
+0.10
0.3 -0.05
0.5 ± 0.2
0.575 MAX
NT
IN
0.1 ± 0.1
ORDERING INFORMATION
8
2
7
3
6
4
5
SC
O
1
PART NUMBER
QUANTITY
MARKING
UPB1506GV-E1
1000/Reel
1506
UPB1507GV-E1-A
1000/Reel
1507
Note:
1. Embossed tape 8 mm wide.
Pin 1 is in the tape pull-out direction.
PIN CONNECTIONS
Pin No. UPB1506GV
UPB1507GV
SW1
IN
2
IN
Vcc
3
IN
SW1
4
GND
OUT
5
OPEN
GND
6
SW2
SW2
7
OUT
OPEN
DI
1
8
Vcc
IN
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
7/22/2004
A Business Partner of NEC Compound Semiconductor Devices, Ltd.
0.87±0.2
D
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
UE
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
IN
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Lead (Pb)
Mercury
< 1000 PPM
Concentration contained
in CEL devices
-A
Not Detected
< 1000 PPM
Not Detected
< 100 PPM
Not Detected
SC
O
Cadmium
Concentration Limit per RoHS
(values are not yet fixed)
NT
Restricted Substance
per RoHS
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
DI
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.