A Business Partner of Renesas Electronics Corporation. Preliminary NE85633 / 2SC3356 JEITA Part No. Data Sheet R09DS0021EJ0300 Rev.3.00 NPN Silicon RF Transistor Jun 28, 2011 NPN Epitaxial Silicon RF Transistor for Microwave Low-Noise Amplification 3-pin Minimold FEATURES • Low noise and high gain : NF = 1.1 dB TYP., Ga = 11 dB TYP. @ VCE = 10 V, IC = 7 mA, f = 1 GHz • High power gain : MAG = 13 dB TYP. @ VCE = 10 V, IC = 20 mA, f = 1 GHz <R> ORDERING INFORMATION Part Number Order Number Package NE85633 2SC3356 NE85633-A 2SC3356-A 3-pin Minimold NE85633-T1B 2SC3356-T1B (Pb-Free) NE85633-T1B-A 2SC3356-T1B-A Quantity Supplying Form 50 pcs (Non reel) • 8 mm wide embossed taping 3 kpcs/reel • Pin 3 (Collector) face the perforation side of the tape Remark To order evaluation samples, please contact your nearby sales office. The unit sample quantity is 50 pcs. ABSOLUTE MAXIMUM RATINGS (TA = +25°C) Parameter Symbol Ratings Unit Collector to Base Voltage VCBO 20 V Collector to Emitter Voltage VCEO 12 V Emitter to Base Voltage VEBO 3.0 V IC 100 mA 200 mW Collector Current Total Power Dissipation Ptot Note Junction Temperature Tj 150 °C Storage Temperature Tstg −65 to +150 °C Note Free air CAUTION Observe precautions when handling because these devices are sensitive to electrostatic discharge. The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 1 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 ELECTRICAL CHARACTERISTICS (TA = +25°C) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit DC Characteristics Collector Cut-off Current ICBO VCB = 10 V, IE = 0 – – 1.0 μA Emitter Cut-off Current IEBO VEB = 1.0 V, IC = 0 – – 1.0 μA VCE = 10 V, IC = 20 mA 50 120 250 – VCE = 10 V, IC = 20 mA – 7 – GHz ⏐S21e⏐ VCE = 10 V, IC = 20 mA, f = 1 GHz – 11.5 – dB NF VCE = 10 V, IC = 7 mA, f = 1 GHz – 1.1 2.0 dB VCB = 10 V, IE = 0, f = 1 MHz − 0.55 1.0 pF DC Current Gain hFE Note 1 RF Characteristics Gain Bandwidth Product fT Insertion Power Gain 2 Noise Figure Reverse Transfer Capacitance Cre Note 2 Notes 1. Pulse measurement: PW ≤ 350 μs, Duty Cycle ≤ 2% 2. Collector to base capacitance when the emitter grounded <R> hFE CLASSIFICATION Rank Q/YQ R/YR S/YS Marking R23 R24 R25 hFE Value 50 to 100 80 to 160 125 to 250 R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 2 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE 200 150 100 50 0 25 50 75 100 125 150 1 0.5 0.3 0.2 0.5 1 2 5 10 20 30 DC CURRENT GAIN vs. COLLECTOR CURRENT GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 10 100 50 20 25 f = 1 MHz Collector to Base Voltage VCB (V) VCE = 10 V 10 0.5 2 Ambient Temperature TA (˚C) Gain Bandwidth Product fT (GHz) DC Current Gain hFE 200 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Reverse Transfer Capacitance Cre (pF) Free air 1 5 10 VCE = 10 V 5 2 1 0.5 0.2 0.1 0.1 50 0.5 1 5 10 50 100 Collector Current IC (mA) Collector Current IC (mA) INSERTION POWER GAIN, MAG vs. FREQUENCY INSERTION POWER GAIN vs. COLLECTOR CURRENT 15 MAG 20 Insertion Power Gain |S21e|2 (dB) Total Power Dissipation Ptot (mW) 250 REVERSE TRANSFER CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE |S21e|2 15 10 5 0 0.05 VCE = 10 V IC = 20 mA 0.1 0.2 0.5 1 2 Frequency f (GHz) VCE = 10 V f = 1 GHz 10 5 0 0.5 1 5 10 50 70 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 3 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 NOISE FIGURE vs. COLLECTOR CURRENT Noise Figure NF (dB) Noise Figure NF (dB) 6 5 4 3 2 1 0 0.5 5 VCE = 10 V f = 1 GHz 1 5 10 50 70 Collector Current IC (mA) f = 1 GHz IC = 20 mA 4 3 2 |S21e|2 12 9 6 NF 1 0 15 3 2 4 6 8 Insertion Power Gain |S21e|2 (dB) 7 NOISE FIGURE, INSERTION POWER GAIN vs. COLLECTOR TO EMITTER VOLTAGE 0 10 Collector to Emitter Voltage VCE (V) Remark The graphs indicate nominal characteristics. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 4 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 SMITH CHART S11e, S22e-FREQUENCY 1.0 70 0.1 6 0.3 4 0.1 0.3 7 3 1.4 60 1.6 0.7 1.8 0. 5 0. 18 32 0. 50 2 .0 0.6 0.2 T EN C O 0 1. 0.8 0 1.8 2.0 0. 5 1.6 0.2 1.4 0.35 0.15 −70 1.2 4 0.3 6 0.1 0.36 0.14 −80 1.0 3 0.3 7 0 −6 0.37 0.13 0.8 0.1 0.9 20 10 5.0 3.0 4.0 1.8 2.0 1.6 1.4 0.9 1.0 0.7 0.8 ( NE G 0.4 0.7 32 18 0. 0. 0 E IV AT 0.6 0. 4 0. 3 0 −1 7 30 0.6 −5 E NC TA X AC −J––O– RE –Z 0.8 0.38 0.39 0.12 0.11 −100 −90 −11 0 0.40 0.10 0.4 1 0.0 0.4 9 0 2 −1 .08 20 S21e-FREQUENCY 0. 3 −4 0.1 1 0 9 IC = 5 mA 0.3 0.2 0 0 0 ) 1.0 0.2 GHz 3. 0.6 1. 5.0 4.0 0.1 IC = 20 mA 4 0.27 0.2 0 .2 8 3 0 0 .2 .29 2 −20 0.2 1 −3 0 IC = 5 mA 0.2 GHz 8 0. 0. −10 S22e 0.6 0.2 10 0.5 1.2 2.0 GHz IC = 20 mA 0.4 50 0.4 0.4 ) 0.26 0.24 ( 50 0 REACTANCE COMPONENT R –––– 0.2 ZO 0.25 0.25 0.3 0.6 10 20 0.2 0.3 0.2 S11e 0.2 6.0 0.24 0.23 0.26 2 0.2 0.27 8 10 0.2 20 4.0 0 1. 20 4 0. 0.8 2.0 GHz 1 0.2 9 0.2 0 3. 0.6 30 ( –Z–+–J–XTANCE CO ) MPO N 0.4 0.1 0.3 0.15 0.35 0 0.2 0 0.3 WAVELE N 0.14 0.36 80 40 GTHS 0 0.01 0.49 0.02 TOWARD 0.48 0 0.49 0.0 GENE 0.01 7 0.48 3 RA 0.4 0.0W2ARD LOADLECTION COEF FCIENT 0.4 0.0TOR 3 HS TO LE OF REF 6 I 7 .0 N DEG 0NGT ANG 4 0.4 REE 0 E 0.4 6 L 0 S .04AVE −1 6 0.0 0 5 W 15 0 0.4 5 0.4 5 0 15 0 − . 5 0 0. 4 0 4 POS 0.1 14 0.4 6 0. 06 ENT ITIV 40 ON 0 ER 4 MP 0. −1 E O A C 0.13 0.37 90 19 0. 31 0. 2 0.4 20 1 07 0. 3 4 0. 0 13 0.12 0.38 0.11 0.39 100 0.9 0 0.10 0.40 110 0.8 .08 9 0.0 1 0.4 1.2 CONDITION : VCE = 10 V, 200 MHz Step S12e-FREQUENCY CONDITION : VCE = 10 V, IC = 20 mA CONDITION : VCE = 10 V, IC = 20 mA 90˚ 90˚ 120˚ 2.0 GHz 60˚ 120˚ 60˚ 0.2 GHz 150˚ 30˚ S21e S12e 150˚ 30˚ 0.2 GHz 180˚ 2.0 GHz 5 10 15 –150˚ 20 0˚ 180˚ –30˚ –60˚ –120˚ –90˚ R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 0.05 0.1 0.15 –150˚ 0.2 0.25 0˚ –30˚ –60˚ –120˚ –90˚ Page 5 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 S-PARAMETERS S-parameters and noise parameters are provided on our Web site in a format (S2P) that enables the direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. Click here to download S-parameters. [RF and Microwave] → [Device Parameters] URL http://www2.renesas.com/microwave/en/download.html R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 6 of 7 A Business Partner of Renesas Electronics Corporation. NE85633 / 2SC3356 PACKAGE DIMENSIONS 3-PIN MINIMOLD (UNIT: mm) 2.8±0.2 1 3 0.4+0.1 –0.05 0.95 0.4+0.1 –0.05 0.95 2 Marking 0 to 0.1 1.1 to 1.4 0.16+0.1 –0.05 0.3 2.9±0.2 0.65+0.1 –0.15 1.5 PIN CONNECTIONS 1. Emitter 2. Base 3. Collector R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 7 of 7 NE85633 / 2SC3356 Data Sheet Revision History Rev. − 3.00 Date Jun 2004 Jun 28, 2011 Description Summary Page − p.1 p.2 Previous No. :PU10209EJ02V0DS Modification of ORDERING INFORMATION Modification of hFE CLASSIFICATION All trademarks and registered trademarks are the property of their respective owners. C-1 NOTICE 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. 5. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by California Eastern Laboratories or Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by California Eastern Laboratories, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a California Eastern Laboratories sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories. 12. Please contact a California Eastern Laboratories sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics. NOTE 3: Products and product information are subject to change without notice. CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com For a complete list of sales offices, representatives and distributors, Please visit our website: www.cel.com/contactus