EN2342QI 4A PowerSoC Datasheet

Enpirion® Power Datasheet
EN2342QI 4A PowerSoC
Voltage Mode Synchronous
PWM Buck with Integrated Inductor
Description
Features
The EN2342QI is a Power System on a Chip
(PowerSoC) DC-DC converter. It integrates MOSFET
switches, small-signal control circuits, compensation
and an integrated inductor in an advanced 8x11x3mm
QFN module. It offers high efficiency, excellent line
and load regulation over temperature and up to the
full 4A load range. The EN2342QI operates over a
wide input voltage range and is specifically designed
to meet the precise voltage and fast transient
requirements of high-performance products. The
EN2342 features frequency synchronization to an
external clock, power OK output voltage monitor,
programmable soft-start along with thermal and over
current protection. The device’s advanced circuit
design, ultra high switching frequency and proprietary
integrated inductor technology delivers high-quality,
ultra compact, non-isolated DC-DC conversion.
•
•
•
•
•
The Altera Enpirion solution significantly helps in
system design and productivity by offering greatly
simplified board design, layout and manufacturing
requirements. In addition, overall system level
reliability is improved given the small number of
components required with the Altera Enpirion
solution.
Applications
All Altera Enpirion products are RoHS compliant,
halogen free and are compatible with lead-free
manufacturing environments.
22nF
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Integrated Inductor, MOSFETs, Controller
Wide Input Voltage Range: 4.5V – 14V
Guaranteed 4A IOUT at 85°C with No Airflow
Frequency Synchronization (External Clock)
1.5% VOUT Accuracy (Over Load and Temperature)
High Efficiency (Up to 95%)
Output Enable Pin and Power OK signal
Programmable Soft-Start Time
Pre-Bias Protection
Pin Compatible with the EN2340/60QI
Under Voltage Lockout Protection (UVLO)
Thermal Soft-Shutdown Protection
Over Current and Short Circuit Protection
RoHS Compliant, MSL Level 3, 260oC Reflow
FPGA Applications, Core, IO, Transceiver
Space Constrained Applications
Output Voltage Ripple Sensitive Applications
Beat Frequency Sensitive Applications
Servers, Embedded Computing Systems,
LAN/SAN Adapter Cards, RAID Storage Systems,
Industrial Automation, Test and Measurement,
and Telecommunications
Efficiency vs. Output Current
0.22µF
95
VOUT
PG BTMP VDDB BGND
VOUT
PVIN
EN2342QI
RVB
4.75k
ON
OFF
22µF
1206
ENABLE
85
COUT
RA
CA
AVINO
1µF
1µF
AVIN
RCA
VFB
EN_PB
SS
PGND
47nF
FQADJ AGND
90
PGND
RCLX
RB
EFFICIENCY (%)
VIN
80
Actual Solution Size
200mm 2
75
70
CONDITIONS
VIN = 12.0V
Dual Supply
65
60
VOUT = 5.0V
55
VOUT = 1.8V
50
0
RFS
0.5
1
1.5
2
2.5
3
3.5
4
OUTPUT CURRENT (A)
RCLX
Figure 1. Simplified Application Circuit
Figure 2. Highest Efficiency in Smallest Solution Size
www.altera.com/enpirion
09520
March 5, 2015
Rev E
EN2342QI
Ordering Information
Part Number
Package Markings
TAMBIENT Rating (°C)
Package Description
EN2342QI
EN2342QI
-40 to +85
68-pin (8mm x 11mm x 3mm) QFN T&R
EVB-EN2342QI
EN2342QI
QFN Evaluation Board
Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html
NC
NC
NC
NC
NC
NC(SW)
NC(SW)
NC(SW)
EN_PB
NC
FQADJ
RCLX
SS
EAOUT
VFB
AGND
AGND
AVIN
ENABLE
POK
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
Pin Assignments (Top View)
48
S_OUT
NC
1
NC
2
47
S_IN
NC
3
46
BGND
NC
4
45
VDDB
NC
5
44
BTMP
NC
6
43
PG
42
AVINO
41
PVIN
40
PVIN
KEEP OUT
69
PGND
KEEP OUT
KEEP OUT
32
33
34
PGND
PGND
PGND
30
PGND
31
29
PGND
PGND
28
VOUT
NC(SW)
PVIN
27
35
NC(SW)
14
26
NC
NC
PVIN
25
36
NC
13
24
NC
VOUT
PVIN
23
37
22
12
VOUT
NC
21
PVIN
VOUT
38
20
11
VOUT
NC
19
PVIN
VOUT
39
18
10
VOUT
NC
17
9
VOUT
NC
16
8
VOUT
NC
15
7
NC
NC
Figure 3: Pin Out Diagram (Top View)
NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. All pins
including NC pins must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage.
NOTE B: Shaded area highlights exposed metal below the package that is not to be mechanically or electrically
connected to the PCB. Refer to Figure 12 for details.
NOTE C: White ‘dot’ on top left is pin 1 indicator on top of the device package.
www.altera.com/enpirion, Page 2
09520
March 5, 2015
Rev E
EN2342QI Datasheet
Pin Description
I/O Legend:
PIN
P=Power
NAME
I/O
1-15,
25-26,
59, 6468
NC
NC
16-24
VOUT
O
27-28,
61-63
NC(SW)
NC
29-34
PGND
G
35-41
PVIN
P
42
AVINO
O
43
PG
I/O
44
BTMP
I/O
45
VDDB
O
46
BGND
G
47
S_IN
I
48
S_OUT
O
49
POK
O
50
ENABLE
I
51
AVIN
P
52, 53
AGND
G
54
VFB
I/O
55
EAOUT
O
56
SS
I/O
57
RCLX
I/O
58
FQADJ
I/O
60
EN_PB
I
G=Ground
NC=No Connect
I=Input O=Output
I/O=Input/Output
FUNCTION
NO CONNECT – These pins may be internally connected. Do not connect them to each
other or to any other electrical signal. Failure to follow this guideline may result in device
damage.
Regulated converter output. Connect these pins to the load and place output capacitor
between these pins and PGND pins 29-34.
NO CONNECT – These pins are internally connected to the common switching node of the
internal MOSFETs. They are not to be electrically connected to any external signal, ground,
or voltage. Failure to follow this guideline may result in damage to the device.
Input/output power ground. Connect these pins to the ground electrode of the input and
output filter capacitors. See VOUT and PVIN pin descriptions for more details.
Input power supply. Connect to input power supply. Decouple with input capacitor to
PGND pins 29-34.
Internal 3.3V linear regulator output. Connect this pin to AVIN (Pin 51) for applications
where operation from a single input voltage (PVIN) is required. If AVINO is being used,
place a 1µF, X5R/X7R, capacitor between AVINO and AGND as close as possible to
AVINO.
PMOS gate. Place a 22nF, X5R/X7R, capacitor between this pin and BTMP. A 560Ω may
be used between PVIN and PG to assist in filtering the input rail in noisy systems.
Bottom plate ground. See pin 43 description.
Internal regulated voltage used for the internal control circuitry. Place a 0.22µF, X5R/X7R,
capacitor between this pin and BGND.
Ground for VDDB. See pin 45 description.
Digital synchronization input. This pin accepts either an input clock to phase lock the
internal switching frequency or a S_OUT signal from another EN2342QI. Leave this pin
floating if not used.
Digital synchronization output. PWM signal is output on this pin. Leave this pin floating if
not used.
Power OK is an open drain transistor (pulled up to AVIN or similar voltage) used for power
system state indication. POK is logic high when VOUT is within -10% of VOUT nominal.
Leave this pin floating if not used.
Output enable. Applying a logic high to this pin enables the output and initiates a soft-start.
Applying a logic low disables the output. ENABLE logic cannot be higher than AVIN (refer to
Absolute Maximum Ratings). Do not leave floating.
3.3V Input power supply for the controller. Place a 1µF, X5R/X7R, capacitor between AVIN
and AGND.
Analog ground. This is the ground return for the controller. All AGND pins need to be
connected to a quiet ground.
External feedback input. The feedback loop is closed through this pin. A voltage divider at
VOUT is used to set the output voltage. The mid-point of the divider is connected to VFB. A
phase lead network from this pin to VOUT is also required to stabilize the loop.
Optional error amplifier output. Allows for customization of the control loop.
Soft-start node. The soft-start capacitor is connected between this pin and AGND. The
value of this capacitor determines the startup time.
Over-current protection. Placement of a resistor on this pin will adjust the over-current
protection threshold. See Table 2 for the recommended RCLX Value to set OCP at the
nominal value specified in the Electrical Characteristics table. No current limit protection
when this pin is left floating.
Adding a resistor (RFS) to this pin will adjust the switching frequency of the EN2342QI. See
Table 1 for suggested resistor values on RFS for various PVIN/VOUT combinations to
maximize efficiency. Do not leave floating.
Enable pre-bias protection. Connect EN_PB directly to AVIN to enable the Pre-Bias Protection
feature. Pull EN_PB directly to ground to disable the feature. Do not leave this pin floating. See PreBias Operation for details.
www.altera.com/enpirion
09520
March 5, 2015
Rev E
EN2342QI
PIN
69
NAME
PGND
I/O
FUNCTION
G
Not a perimeter pin. Device thermal pad to be connected to the system GND plane for heatsinking purposes.
Absolute Maximum Ratings
CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating
conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute
maximum rated conditions for extended periods may affect device reliability.
MIN
MAX
UNITS
Voltages on : PVIN, VOUT, PG
PARAMETER
SYMBOL
-0.5
15
V
Voltages on: ENABLE, POK, EN_PB
-0.3
AVIN+0.3
V
Dual Supply PVIN Rising and Falling Slew Rate (Note 1)
25
V/ms
Single Supply PVIN Rising and Falling Slew Rate (Note 1)
10
V/ms
Pin Voltages – AVINO, AVIN, S_IN, S_OUT
3.0
6.0
V
Pin Voltages – VFB, SS, EAOUT, RCLX, FQADJ, VDDB, BTMP
-0.5
2.75
V
-65
150
°C
150
°C
Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A
260
°C
ESD Rating (based on Human Body Model)
2000
V
ESD Rating (based on CDM)
500
V
Storage Temperature Range
TSTG
Maximum Operating Junction Temperature
TJ-ABS Max
Recommended Operating Conditions
SYMBOL
MIN
MAX
UNITS
Input Voltage Range
PARAMETER
PVIN
4.5
14
V
AVIN: Controller Supply Voltage
AVIN
3.0
5.5
V
Output Voltage Range (Note 2)
VOUT
0.75
5
V
Output Current
IOUT
4
A
Operating Ambient Temperature
TA
-40
+85
°C
Operating Junction Temperature
TJ
-40
+125
°C
Thermal Characteristics
SYMBOL
TYP
UNITS
Thermal Resistance: Junction to Ambient (0 LFM) (Note 3)
PARAMETER
θJA
18
°C/W
Thermal Resistance: Junction to Case (0 LFM)
θJC
2
°C/W
Thermal Shutdown
TSD
150
°C
Thermal Shutdown Hysteresis
TSDH
35
°C
Note 1: PVIN rising and falling slew rates cannot be outside of specification. After the device is powered, the input voltage
transients should be kept under 1V peak-to-peak under all conditions. A noisy input rail will affect device performance. For
accurate power up sequencing, use a fast ENABLE logic (>3V/100µs) after both AVIN and PVIN is high.
Note 2: Dropout: Maximum VOUT ≤ VIN - 2.5V
Note 3: Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for high
thermal conductivity boards.
Characteristics
NOTE: VIN=12V, Minimum and Maximum values are over operating ambient temperature range (-40°C ≤ TA ≤ +85°C)
unless otherwise noted. Typical values are at TA = 25°C.
www.altera.com/enpirion, Page 4
09520
March 5, 2015
Rev E
EN2342QI
PARAMETER
Operating Input Voltage
SYMBOL
PVIN
Controller Input Voltage
AVIN
TEST CONDITIONS
MIN
4.5
TYP
3.0
MAX
14.0
UNITS
V
5.5
V
AVIN UVLO Rising
AVINUVLOR
UVLO is not asserted
2.5
2.75
3.0
V
AVIN UVLO Falling
AVINOVLOF
UVLO is asserted
2.1
2.35
2.6
V
AVIN UVLO Hysteresis
AVINHYS
400
AVIN Pin Input Current
IAVIN
7
AVINO
3.3
V
Internal LDO Output
mV
15
mA
IPVINS
PVIN=12V, AVIN=3.3V, ENABLE=0V
2
mA
IAVINS
PVIN=12V, AVIN=3.3V, ENABLE=0V
300
µA
Feedback Pin Voltage
VFB
VIN = 12V, ILOAD = 0, TA = 25°C Only
0.7425
0.750
0.7575
V
Feedback Pin Voltage
(Load and Temperature)
VFB
0A ≤ ILOAD ≤ 4A
Starting Date Code: X510 or greater
0.739
0.750
0.761
V
Feedback Pin Voltage
(Line, Load, Temperature)
VFB
4.5V ≤ VIN ≤ 14V; 0A ≤ ILOAD ≤ 4A
0.735
0.750
0.765
V
Feedback Pin Input
Leakage Current
IFB
VFB pin input leakage current
(Note 4)
5
nA
Shut-Down Supply Current
VOUT Rise Time
Soft-Start Capacitor Range
tRISE
-5
CSS = 47nF (Note 5 and Note 6)
3.2
CSS_RANGE
10
Output Current Range
IOUT
0
Over Current Trip Level
IOCP
PVIN=12V, VOUT=1.2V
IIN_AVG_OCP
Short = 10mΩ (Note 7)
Disable Threshold
VDISABLE
ENABLE pin logic Low
0.0
0.95
V
ENABLE Threshold
VENABLE
ENABLE pin logic High
1.25
AVIN
V
ENABLE Hysteresis
ENHYS
200
mV
ENABLE Lockout Time
TENLOCKOUT
8
ms
ENABLE Input Current
IENABLE
4
µA
1.0
MHz
Short Circuit Average Input
Current
Switching Frequency
FSW
370k internal pull-down (Note 4)
RFS =3kΩ
External SYNC Clock
Frequency Lock Range
FPLL_LOCK
Range of SYNC clock frequency
(See Table 1)
S_IN Threshold – Low
VS_IN_LO
S_IN clock logic low level (Note 4)
VS_IN_HI
S_IN clock logic high level (Note 4)
S_IN Threshold – High
S_OUT Threshold – Low
VS_OUT_LO
S_OUT clock logic low level (Note 4)
S_OUT Threshold – High
VS_OUT_HI
S_OUT clock logic high level (Note 4)
POK Lower Threshold
POKLT
VOUT / VOUT_NOM
POK Output low Voltage
VPOKL
With 4mA current sink into POK
POK Output Hi Voltage
VPOKH
PVIN range: 4.5V ≤ VIN ≤ 14V
POK VOH Leakage Current
IPOKL
POK High (Note 4)
Note
Note
Note
Note
4.15
47
ms
68
nF
4
A
6
A
100
mA
0.9
1.8
1.8
1.8
MHz
0.8
V
2.5
V
0.8
V
2.5
V
90
%
0.4
V
AVIN
V
1
µA
4: Parameter not production tested but is guaranteed by design.
5: Rise time calculation begins when AVIN > VUVLO and ENABLE = HIGH.
6: VOUT Rise Time Accuracy does not include soft-start capacitor tolerance.
7: Output short circuit condition was performed with load impedance that is greater than or equal to 10mΩ.
www.altera.com/enpirion, Page 5
09520
March 5, 2015
Rev E
EN2342QI
Typical Performance Curves
Efficiency vs. Output Current
100
90
95
85
90
80
75
VOUT = 5.0V
70
VOUT = 3.3V
65
VOUT = 2.5V
60
VOUT = 1.2V
55
VOUT = 1.0V
85
EFFICIENCY (%)
EFFICIENCY (%)
Efficiency vs. Output Current
95
CONDITIONS
VIN = 12.0V
AVIN = 3.3V
Dual Supply
80
75
VOUT = 5.0V
70
VOUT = 3.3V
65
VOUT = 2.5V
60
VOUT = 1.2V
55
VOUT = 1.2V
50
50
0
0.5
1
1.5
2
2.5
OUTPUT CURRENT (A)
3
3.5
0
4
0.5
95
95
90
90
85
85
80
75
70
65
VOUT = 2.5V
60
VOUT = 1.2V
55
VOUT = 1.0V
1
1.5
2
2.5
OUTPUT CURRENT (A)
3
3.5
4
Efficiency vs. Output Current
100
EFFICIENCY (%)
EFFICIENCY (%)
Efficiency vs. Output Current
CONDITIONS
VIN = 5.0V
CONDITIONS
AVIN = 3.3V
VIN = 8.0V
Dual
Supply
80
CONDITIONS
VIN = 12.0V
75
70
DUAL SUPPLY VOUT = 5.0V
65
SINGLE SUPPLY VOUT = 5.0V
60
DUAL SUPPLY VOUT = 1.0V
55
SINGLE SUPPLY VOUT = 1.0V
50
50
0
0.5
1
1.5
2
2.5
OUTPUT CURRENT (A)
3
3.5
0
4
0.5
1
1.5
2
2.5
3
3.5
4
OUTPUT CURRENT (A)
Output Voltage vs. Output Current
Output Voltage vs. Output Current
1.010
3.310
1.008
VIN = 5V
1.006
VIN = 8V
1.004
VIN = 12V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
CONDITIONS
VIN = 8.0V
CONDITIONS
AVIN
= 3.3V
VIN = Supply
8.0V
Dual
1.002
1.000
0.998
0.996
0.994
VIN = 8V
3.306
VIN = 12V
3.304
CONDITIONS
VOUT_NOM = 3.3V
3.302
3.300
3.298
3.296
3.294
CONDITIONS
CONDITIONS
VOUT_NOM
VIN ==5.0V
1.0V
0.992
3.308
3.292
0.990
3.290
0.0
0.5
1.0 1.5 2.0 2.5 3.0
OUTPUT CURRENT (A)
3.5
4.0
0.0
0.5
1.0 1.5 2.0 2.5 3.0
OUTPUT CURRENT (A)
3.5
4.0
www.altera.com/enpirion, Page 6
09520
March 5, 2015
Rev E
EN2342QI
Typical Performance Curves (Continued)
Output Voltage vs. Input Voltage
Output Voltage vs. Input Voltage
3.320
CONDITIONS
VOUT_NOM = 1.0V
1.015
Load = 0A
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.020
Load = 1A
Load = 2A
1.010
Load = 3A
1.005
Load = 4A
1.000
0.995
CONDITIONS
VOUT_NOM = 3.3V
3.315
3.310
Load = 2A
3.305
Load = 3A
3.300
Load = 4A
3.295
3.290
3.280
2
4
6
8
10
12
INPUT VOLTAGE (V)
14
16
2
4
6
8
10
12
INPUT VOLTAGE (V)
14
16
Output Voltage vs. Temperature
Output Voltage vs. Temperature
1.204
1.204
CONDITIONS
VIN = 8V
VOUT_NOM = 1.2V
1.203
1.202
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Load = 1A
3.285
0.990
1.201
1.200
LOAD = 0A
1.199
LOAD = 1A
LOAD = 2A
1.198
LOAD = 3A
1.197
CONDITIONS
VIN = 10V
VOUT_NOM = 1.2V
1.203
1.202
1.201
1.200
LOAD = 0A
1.199
LOAD = 1A
LOAD = 2A
1.198
LOAD = 3A
1.197
LOAD = 4A
LOAD = 4A
1.196
1.196
-40
35
60
-15
10
AMBIENT TEMPERATURE ( C)
-40
85
-15
10
35
60
AMBIENT TEMPERATURE ( C)
85
Output Voltage vs. Temperature
Output Voltage vs. Temperature
1.204
1.204
CONDITIONS
VIN = 12V
VOUT_NOM = 1.2V
1.203
1.202
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Load = 0A
1.201
1.200
LOAD = 0A
1.199
LOAD = 1A
LOAD = 2A
1.198
LOAD = 3A
1.197
CONDITIONS
VIN = 14V
VOUT_NOM = 1.2V
1.203
1.202
1.201
1.200
LOAD = 0A
1.199
LOAD = 1A
LOAD = 2A
1.198
LOAD = 3A
1.197
LOAD = 4A
LOAD = 4A
1.196
1.196
-40
-15
10
35
60
AMBIENT TEMPERATURE ( C)
85
-40
-15
10
35
60
AMBIENT TEMPERATURE ( C)
85
www.altera.com/enpirion, Page 7
09520
March 5, 2015
Rev E
EN2342QI
Typical Performance Characteristics
Output Ripple at 20MHz Bandwidth
Output Ripple at 500MHz Bandwidth
CONDITIONS
VIN = 12V
VOUT = 1V
IOUT = 2A
CIN = 2 x 22µF (1206)
COUT = 2 x 47 µF (1206)
CONDITIONS
VIN = 12V
VOUT = 1V
IOUT = 2A
CIN = 2 x 22µF (1206)
COUT = 2 x 47 µF (1206)
VOUT
(AC Coupled)
VOUT
(AC Coupled)
Output Ripple at 20MHz Bandwidth
VOUT
(AC Coupled)
Output Ripple at 500MHz Bandwidth
CONDITIONS
VIN = 12V
VOUT = 1V
IOUT = 4A
CIN = 2 x 22µF (1206)
COUT = 2 x 47 µF (1206)
VOUT
(AC Coupled)
Enable Startup/Shutdown Waveform (0A)
Enable Startup/Shutdown Waveform (4A)
ENABLE
ENABLE
VOUT
VOUT
POK
POK
LOAD
CONDITIONS
VIN = 12V
VOUT = 1V
IOUT = 4A
CIN = 2 x 22µF (1206)
COUT = 2 x 47 µF (1206)
CONDITIONS
VIN = 12V, VOUT = 1.0V, No Load, Css = 47nF
CIN = 2 x 22µF (1206), COUT = 2 x 47 µF (1206)
LOAD
CONDITIONS
VIN = 12V, VOUT = 1.0V, LOAD = 4A, Css = 47nF
CIN = 2 x 22µF (1206), COUT = 2 x 47 µF (1206)
www.altera.com/enpirion, Page 8
09520
March 5, 2015
Rev E
EN2342QI
Typical Performance Characteristics (Continued)
Load Transient from 50mA to 2A
Load Transient from 50mA to 4A
VOUT = 1V
(AC Coupled)
20mV / DIV
VOUT = 1V
(AC Coupled)
50mV / DIV
CONDITIONS
VIN = 12V, VOUT = 1V
CIN = 22µF (1206)
COUT = 2 x 22µF (0805)
Small Solution Size Configuration
LOAD
LOAD
Load Transient from 2A to 4A
CONDITIONS
VIN = 12V, VOUT = 1V
CIN = 22µF (1206)
COUT = 2 x 22µF (0805)
Small Solution Size Configuration
Load Transient from 50mA to 4A
VOUT = 1.8V
(AC Coupled)
100mV / DIV
VOUT = 1.8V
(AC Coupled)
100mV / DIV
LOAD
CONDITIONS
VIN = 12V, VOUT = 1.8V
CIN = 22µF (1206)
COUT = 2 x 22µF (0805)
Small Solution Size Configuration
LOAD
Load Transient from 50mA to 3A
Load Transient from 50mA to 3A
VOUT = 3.3V
(AC Coupled)
100mV / DIV
VOUT = 3.3V
(AC Coupled)
100mV / DIV
LOAD
CONDITIONS
VIN = 12V, VOUT = 1.8V
CIN = 22µF (1206)
COUT = 2 x 22µF (0805)
Small Solution Size Configuration
CONDITIONS
VIN = 12V, VOUT = 3.3V
CIN = 22µF (1206)
COUT = 2 x 22µF (0805)
Small Solution Size Configuration
LOAD
CONDITIONS
VIN = 12V, VOUT = 3.3V
CIN = 22µF (1206)
COUT = 2 x 47µF (1206)
Best Performance Configuration
www.altera.com/enpirion, Page 9
09520
March 5, 2015
Rev E
EN2342QI
Typical Performance Characteristics (Continued)
Pre-Bias Shutdown Waveform
Pre-Bias Startup Waveform
PVIN = 12V
PVIN = 12V
ENABLE
ENABLE
VOUT
VOUT
Max Pre-Bias
<100% of Nominal
VOUT is held low
for another ~6ms
CONDITIONS
VIN = 12V (Single Supply Only)
VOUT = 1.0V, Load = 0A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)
CONDITIONS
VIN = 12V (Single Supply Only)
VOUT = 1.0V, Load = 0A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)
www.altera.com/enpirion, Page 10
09520
March 5, 2015
Rev E
EN2342QI
Functional Block Diagram
S_OUT S_IN
UVLO
Digital I/O
BTMP
PVIN
PG
Linear
Regulator
To PLL
AVINO
Thermal Limit
Current Limit
NC(SW)
Gate Drive
VOUT
BGND
(-)
PWM
Comp
(+)
FQADJ
PGND
VDDB
Compensation
Network
PLL/Sawtooth
Generator
EAOUT
VFB
(-)
Error
Amp
(+)
Power
Good
Logic
SS
Soft Start
ENABLE
POK
300k
Voltage Reference Generator
370k
Band Gap
Reference
EN2342QI
AVIN EN_PB AGND
Figure 4: Functional Block Diagram
Functional Description
capacitors, as well as a wide loop bandwidth within
a small foot print.
Synchronous Buck Converter
The EN2342QI is a highly integrated synchronous,
buck converter with integrated controller, power
MOSFET switches and inductor. The nominal input
voltage (PVIN) range is 4.5V to 14V and can
support up to 4A of continuous output current. The
output voltage is programmed using an external
resistor divider network. The control loop utilizes a
Type IV Voltage-Mode compensation network and
maximizes on a low-noise PWM topology. Much of
the compensation circuitry is internal to the device.
However, a phase lead capacitor is required along
with the output voltage feedback resistor divider to
complete the Type IV compensation network.. The
high switching frequency of the EN2342QI enables
the use of small size input and output filter
Protection Features:
The power supply has the following protection
features:
• Pre-Bias Protection
• Over-Current and Short Circuit Protection
• Thermal Soft-Shutdown with Hysteresis.
• Under-Voltage Lockout Protection
Additional Features:
•
•
•
Switching Frequency Synchronization.
Programmable Soft-Start
Power OK Output Monitoring
www.altera.com/enpirion, Page 11
09520
March 5, 2015
Rev E
EN2342QI
Modes of Operation
Enable Operation
The EN2342QI is designed to be powered by either
a single input supply (PVIN) or two separate
supplies: one for PVIN and the other for AVIN. The
EN2342QI is not “hot pluggable.” Refer to the PVIN
Slew Rate specification on page 4.
The ENABLE pin provides a means to enable
normal operation or to shut down the device. A
logic high will enable the converter into normal
operation. When the ENABLE pin is asserted (high)
the device will undergo a normal soft-start. A logic
low will disable the converter. A logic low will power
down the device in a controlled manner and the
device is subsequently shut down. The ENABLE
signal has to be low for at least the ENABLE
Lockout Time (8ms) in order for the device to be reenabled. To ensure accurate startup sequencing
the ENABLE/DISABLE signal should be faster than
1V/100µs. A slower ENABLE/DISABLE signal may
result in a delayed startup and shutdown response.
Do not leave ENABLE floating.
Single Input Supply Application (PVIN Only):
22nF
0.22µF
VOUT
PG BTMP VDDB BGND
VOUT
VIN
PVIN
EN2342QI
RVB
4.75k
ON
OFF
22µF
1206
ENABLE
COUT
RA
CA
AVINO
1µF
AVIN
1µF
RCA
VFB
EN_PB
SS
PGND
47nF
FQADJ AGND
RFS
PGND
Pre-Bias Operation
RB
RCLX
RCLX
Figure 5: Single Input Supply Schematic
In single input supply mode, the EN2342QI only
requires one input voltage rail (typically 12V). The
EN2342QI has an internal linear regulator that
converts PVIN to 3.3V. The output of the linear
regulator is provided on the AVINO pin once the
device is enabled. AVINO should be connected to
AVIN. Also, in this single supply application, place a
resistor (RVB) between VDDB and AVIN, as shown
in Figure 5. Altera recommends RVB=4.75kΩ.
Dual Input Supply Application (PVIN and AVIN):
22nF
0.22µF
VOUT
PG BTMP VDDB BGND
VOUT
VIN
PVIN
EN2342QI
COUT
ON
22µF
1206
OFF
ENABLE
RA
CA
AVINO
VAVIN
AVIN
RCA
1µF
VFB
EN_PB
SS
PGND
47nF
FQADJ AGND
RFS
PGND
RCLX
RB
RCLX
Figure 6: Dual Input Supply Schematic
In dual input supply mode, two input voltage rails
are required (typically 12V for PVIN and 3.3V for
AVIN). Refer to Figure 6 for the recommended
schematic for a dual input supply application.
Since AVINO is not used, it can be left open.
The EN2342QI has a Pre-Bias feature which will
allow the regulator to startup into a pre-charged
output. The pre-biased output voltage must be
below the nominal regulation voltage; otherwise,
damage may occur during startup and shutdown.
To use this feature, the EN2342QI must be
configured to Single Supply mode, set to
standalone operation (no parallel operation) and
follow the instructions below:
• The EN_PB pin must be pulled high to AVIN
• A resistor divider must be connected from
PVIN to ENABLE to Ground (10k on top,
4.02k on the bottom) to ensure proper
shutdown. The resistor divider will disable
the device when PVIN falls below
approximately 4.5V. The resistor divider
values may be adjusted accordingly to meet
PVIN requirements. See Figure X.
• PVIN rail should be in regulation (>4.5V)
prior to being enabled.
• Since the ENABLE pin is tied to the resistor
divider to PVIN, an open drain (such as the
POK signal of another regulator or
Sequencer) should be tied to ENABLE in
order to keep the device disabled while the
PVIN rail rises into regulation.
• Once the PVIN rail is in regulation, the
ENABLE may be pulled high through the
resistor divider.
• The ENABLE rise time must be faster than
3V/100us.
The output will start up from the Pre-Bias voltage
into regulation monotonically if the instructions are
followed; otherwise, the Pre-Bias Protection feature
www.altera.com/enpirion, Page 12
09520
March 5, 2015
Rev E
EN2342QI
22nF
Need Fast
ENABLE Logic
(>3V/100us)
VIN
PG
0.22µF
BTMP VDDB
PVIN
10k
EN2342QI
4.75k
COUT
ENABLE
22µF
1206
VOUT
BGND
VOUT
RA
4.01k
CA
AVINO
1µF
AVIN
1µF
RCA
by adjusting the switching frequency. Table 1
shows recommended RFS values for various
PVIN/VOUT combinations in order to optimize
performance of the EN2342QI. It is recommended
to use RFS values that are at least equal to or
higher than Table 1, never lower.
Rfs vs. SW Frequency
SWITCHING FREQUENCY (MHz)
may not function properly. Starting up into a PreBias voltage without the Pre-Bias Protection feature
enabled can lead to device damage. When using
the Pre-Bias feature, the device must be disabled
using the ENABLE pin prior to PVIN falling out of
regulation (<4.5V), otherwise damage may occur
during shutdown. To disable the Pre-Bias feature
pull the EN_PB pin directly to ground. Do not leave
the EN_PB pin floating. See Typical Performance
Characteristics for an example of Pre-Bias
Protection. See Figure X for a typical schematic
with Pre-Bias Protection enabled.
1.80
1.70
1.60
1.50
1.40
1.30
1.20
1.10
1.00
0.90
0.80
0.70
0.60
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
RFS RESISTOR VALUE (kΩ)
VFB
EN_PB
SS
PGND
PGND
47nF
FQADJ AGND
RFS
RCLX
CONDITIONS
VIN = 6V to 12V
VOUT = 0.8V to 5.0V
Figure 7. Typical RFS vs. Switching Frequency
RB
PVIN
RCLX
Figure X. Pre-Bias Application Circuit
Frequency Synchronization
The switching frequency of the EN2342QI can be
phase-locked to an external clock source to move
unwanted beat frequencies out of band. The
internal switching clock of the EN2342QI can be
phase locked to a clock signal applied to the S_IN
pin. An activity detector recognizes the presence of
an external clock signal and automatically phaselocks the internal oscillator to this external clock.
Phase-lock will occur as long as the input clock
frequency is in the range of 0.9MHz to 1.8MHz. The
external clock frequency must be within ±10% of
the nominal switching frequency set by the RFS
resistor. It is recommended to use a synchronized
clock frequency close to the typical frequency
recommendations in Table 1. A 3.01kΩ resistor
from FQADJ to ground is recommended for clock
frequencies within ±10% of 1MHz. When multiple
devices are connected to a single external clock,
use a clock frequency normally used by the highest
output voltage device (the highest frequency).
When no clock is present, the device reverts to the
free running frequency of the internal oscillator set
by the RFS resistor.
The efficiency performance of the EN2342QI for
various PVIN/VOUT combinations can be optimized
4.5V
to
14V
VOUT
5.0V
3.3V
2.5V
1.8V
1.5V
1.2V
<1.0V
RFS
30k
22k
10k
4.87k
3.01k
3.01k
3.01k
Typical fsw
1.48 MHz
1.42 MHz
1.3 MHz
1.15 MHz
1.0 MHz
1.0 MHz
1.0 MHz
Table 1: Recommended RFS Values
Soft-Start Operation
Soft start is a means to ramp the output voltage
gradually upon start-up. The output voltage rise
time is controlled by the choice of soft-start
capacitor, which is placed between the SS pin (pin
56) and the AGND pin (pin 52). During start-up of
the converter, the reference voltage to the error
amplifier is linearly increased to its final level by an
internal current source of approximately 10µA. The
soft-start time is measured from when VIN > VUVLOR
and ENABLE pin voltage crosses its logic high
threshold to when VOUT reaches its programmed
value. The total soft-start time can be calculated by:
Soft Start Time (ms): TSS ≈ Css [nF] x 0.067
Typical soft-start time is approximately 3.2ms with
SS capacitor value of 47nF.
www.altera.com/enpirion, Page 13
09520
March 5, 2015
Rev E
EN2342QI
POK Operation
PVIN
The POK signal is an open drain signal (requires a
pull up resistor to AVIN or similar voltage) from the
converter indicating the output voltage is within the
specified range. Typically, a 100kΩ or lower
resistance is used as the pull-up resistor. The POK
signal will be logic high (AVIN) when the output
voltage is above 90% of the programmed voltage
level. If the output voltage is below this point, the
POK signal will be a logic low. The POK signal can
be used to sequence down-stream converters by
tying to their enable pins.
Over-Current Protection (OCP)
The current limit function is achieved by sensing
the current flowing through a high-side sense
PFET. If the current exceeds the OCP threshold,
the switching cycle is terminated and an OCP
counter is incremented. If the counter value
reaches 32 OCP cycles, the device will shut down
as described below. If there are 8 consecutive
cycles that do not exceed the OCP threshold, the
counter will reset. Once the OCP counter has
reached 32 cycles, the MOSFET switches will tristate and the soft start capacitor will be discharged.
After approximately 32ms the device will attempt a
restart. If the OCP condition persists, the device
will enter a hiccup mode until the OCP condition is
removed. The OCP trip point depends on PVIN,
VOUT, RCLX, RFS and is meant to protect the
device from damage. OCP is not an adjustable
threshold. For a list of RCLX values, see Table 2.
4.5V
to
14V
VOUT
5.0V
3.3V
2.5V
1.8V
1.5V
1.2V
≤1.0V
RCLX
68.1k
61.9k
56.2k
54.9k
53.6k
46.4k
38.3k
RFS
30k
22k
10k
4.87k
3.01k
3.01k
3.01k
Table 2: Recommended RCLX Values
Note: Do not leave RCLX floating.
Thermal Overload Protection
Thermal shutdown circuit will disable device
operation when the junction temperature exceeds
approximately 150°C. The device will go through a
soft-shutdown and allow the output to discharge in
a controlled manner. This prevents excessive
output ringing in the event of a thermal fault
condition. After a thermal shutdown event, when
the junction temperature drops by approximately
35°C, the converter will re-start with a normal softstart.
Input Under-Voltage Lock-out (UVLO)
Internal circuits ensure that the converter will not
start switching until the AVIN input voltage is above
the specified minimum voltage. Hysteresis, input
de-glitch and output leading edge blanking ensures
high noise immunity and prevents false UVLO
triggers.
www.altera.com/enpirion, Page 14
09520
March 5, 2015
Rev E
EN2342QI
Application Information
Output Voltage Programming and Loop
Compensation
The EN2342QI uses a Type IV Voltage Mode
compensation network. Type IV Voltage Mode
control is a proprietary Altera Enpirion control
scheme that maximizes control loop bandwidth to
deliver excellent load transient responses and
maintain output regulation with pin point accuracy.
For ease of use, most of this network has been
customized and is integrated within the device
package.
The EN2342QI output voltage is programmed using
a simple resistor divider network (RA and RB). The
feedback voltage at VFB is nominally 0.75V. RA
depends on Table 6 and RB can be calculated
based on Figure 8. The values recommended for
COUT, CA, and RCA make up the external
compensation of the EN2342QI. It will vary with
each PVIN and VOUT combination to optimize on
performance. The EN2342QI solution can be
optimized for either smallest size or highest
performance. Please see Table 6 for a list of
recommended RA, CA, RCA, and COUT values for
each solution. Since VFB is a sensitive node, do
not touch the VFB node while the device is in
operation as doing so may introduce parasitic
capacitance into the control loop that causes the
device to behave abnormally and damage may
occur. Be sure to use the recommended switching
frequency for each output voltage.
VOUT
VOUT
COUT
RA
CA
should be used as input capacitors for this
converter. The dielectric must be X5R or X7R
rated. Y5V or equivalent dielectric formulations
must not be used as these lose too much
capacitance with frequency, temperature and bias
voltage. In some applications, lower value
capacitors are needed in parallel with the larger,
capacitors in order to provide high frequency
decoupling.
Table 3 contains a list of
recommended input capacitors.
Recommended Input Capacitors
Description
22µF, 16V,
X5R, 10%,
1206
22µF, 16V,
X5R, 20%,
1206
VFB
EN2342QI
<10
VFB x RA
GRM31CR61C226ME15
Taiyo Yuden
EMK316ABJ226ML-T
As seen from Table 6, the EN2342QI has been
optimized for use with either two 47µF/1206 or two
22µF/0805 output capacitors. Low ESR ceramic
capacitors are required with X5R or X7R rated
dielectric formulation. Y5V or equivalent dielectric
formulations must not be used as these lose too
much capacitance with frequency, temperature and
bias voltage. Table 5 contains a list of
recommended output capacitors. In some
applications, extra bulk capacitance is required at
the load. In this case, up to 1000µF of bulk
capacitance may be used at the load as long as the
minimum ESR between the device output and the
bulk capacitance is maintained. Table 4 shows the
recommended compensation components for
applications that require bulk capacitance at the
load.
VFB = 0.75V
RB =
Murata
Table 3: Recommended Input Capacitors
≥10
PGND
P/N
Output Capacitor Selection
PVIN (V)
4.5 to 14
RCA
MFG
VOUT (V)
≥2.5
0.6 to 1.5
Min. ESR
4mΩ
9mΩ
1.5 to 2.5
0.6 to 1.5
7mΩ
12mΩ
1.5 to 2.5
9mΩ
Com pensation
COUT = 2x47µF/1206
Bulk Cap ≤ 1000µF
CA = 100pF
RA = 250kΩ
RCA = 5kΩ
VOUT - VFB
Table 4: Minimum ESR for Bulk Capacitance at Load
Figure 8: VOUT Resistor Divider & Compensation
Components. See Table 6 for details.
Input Capacitor Selection
The EN2342QI requires a 22µF/1206 input
capacitor. Low-cost, low-ESR ceramic capacitors
Note that when bulk capacitors are used the
converter must work harder during startup in order
to raise the output voltage from zero volts into
regulation. If there is too much output capacitance,
the device can hit current limit before it is able to
www.altera.com/enpirion, Page 15
09520
March 5, 2015
Rev E
EN2342QI
raise the output into regulation. If current limit is
reached the device stops switching, the output will
be discharged and the cycle repeats itself
indefinitely. The equation below can be used to
estimate the maximum output capacitance allowed
based on current limit. Since the maximum output
capacitance in the calculation does not account for
temperature or part to part variations, it is always
good to add margin by using a value that is 80% of
the calculated output capacitance value.
COUT_MAX = ITOTAL * dt / dv * 0.8
ESR, and
reactance.
effective
Placing output capacitors in parallel reduces the
impedance and will hence result in lower ripple
voltage.
1
Z Total
The output capacitance can also influence the
output ripple. Output ripple voltage is determined by
the aggregate output capacitor impedance.
Capacitor impedance, denoted as Z, is comprised
of capacitive reactance, effective series resistance,
=
1
1
1
+
+ ... +
Z1 Z 2
Zn
Recommended Output Capacitors
Description
COUT_MAX = Maximum allowable output capacitance
ITOTAL = Max output current of device minus the load
during startup
dv = Change in voltage (which is 0 to VOUT)
dt = Soft-start time (ms) ≈ Css [nF] x 0.067
series inductance, ESL
MFG
P/N
47µF, 6.3V, X5R,
20%, 1206
Murata
GRM31CR60J476ME19L
47µF, 10V, X5R,
20%, 1206
Taiyo
Yuden
LMK316BJ476ML- T
22µF, 10V, X5R,
20%, 0805
Panasonic
ECJ-2FB1A226M
22µF, 10V, X5R,
20%, 0805
Taiyo
Yuden
LMK212BJ226MG- T
Table 5: Recommended Output Capacitors
www.altera.com/enpirion, Page 16
09520
March 5, 2015
Rev E
EN2342QI
Low VOUT Ripple
Smallest Solution Size
CIN = 1 x 22µF/1206
COUT = 2 x 47µF/1206
CIN = 1 x 22µF/1206
RA= 180/(Vout0.5) kΩ
COUT = 2 x 22µF/0805
Nominal Nominal
Nominal Nominal
RCA
RCA
PVIN
VOUT
CA (pF)
Ripple Deviation RA (kΩ)
CA (pF)
Ripple
Deviation
(kΩ)
(kΩ)
(mV)
(mV)
(mV)
(mV)
≤1.0V
10
30
≤5
≤47
75
27
0.1
≤10
≤34
1.2V
12
27
6
48
43
39
0.1
13
33
1.5V
15
27
5
53
56
39
0.1
15
38
14V
1.8V
22
27
6
54
56
39
0.1
18
41
2.5V
27
24
8
55
51
39
0.1
26
59
3.3V
39
18
11
63
51
33
0.1
35
63
5.0V
47
8.2
18
97
75
22
5.1
42
115
≤1.0V
18
22
≤4
≤48
27
47
0.1
≤10
≤35
1.2V
22
22
5
49
75
47
0.1
13
37
1.5V
27
20
5
53
75
47
0.1
15
38
12V
1.8V
33
20
6
54
75
47
0.1
17
44
2.5V
47
18
7
54
56
47
0.1
25
59
3.3V
56
15
10
66
51
39
0.1
32
63
5.0V
56
10
16
99
75
22
5.1
39
128
≤1.0V
33
18
≤3
≤45
27
82
0.1
≤9
≤35
1.2V
39
18
4
46
30
100
0.1
13
39
1.5V
47
18
5
54
30
100
0.1
14
43
10V
1.8V
56
16
6
56
30
100
0.1
17
50
2.5V
68
12
7
57
75
56
0.1
26
70
3.3V
82
10
9
68
56
47
0.1
30
83
5.0V
100
4.3
14
98
75
33
5.1
33
140
≤1.0V
100
8.2
≤3
≤51
100
100
0.1
≤10
≤41
1.2V
100
8.2
4
51
100
100
0.1
12
43
1.5V
100
8.2
4
54
100
100
0.1
14
46
8.0V
1.8V
100
8.2
5
57
100
100
0.1
16
53
2.5V
100
8.2
6
64
91
82
0.1
23
71
3.3V
100
8.2
8
70
75
56
0.1
25
85
5.0V
100
8.2
10
110
75
56
5.1
30
127
≤1.0V
100
8.2
≤3
≤60
100
100
0.1
≤9
≤46
1.2V
100
8.2
4
63
100
100
0.1
12
51
1.5V
100
8.2
4
65
100
100
0.1
14
56
6.6V
1.8V
100
8.2
5
68
100
100
0.1
16
61
2.5V
100
8.2
5
75
100
100
0.1
19
83
3.3V
100
8.2
6
85
91
82
0.1
22
106
≤1.0V
100
8.2
≤3
≤73
100
100
0.1
≤9
≤56
1.2V
100
8.2
3
75
100
100
0.1
11
63
5V
1.5V
100
8.2
4
76
100
100
0.1
13
70
1.8V
100
8.2
4
80
100
100
0.1
13
78
2.5V
100
8.2
4
88
100
100
0.1
14
98
Table 6: RA, CA, and RCA Values for Various PVIN/VOUT Combinations: Low V OUT Ripple vs. Smallest Solution Size. See
Figure 8. Use the equation in Figure 8 to calculate RB (for low VOUT ripple option). Output Ripple is measured at
no load and Nominal Deviation is for a 2A load transient step in one direction. For compensation values of output
voltage in between the specified output voltages, choose compensation values of the lower output voltage
setting.
www.altera.com/enpirion, Page 17
09520
March 5, 2015
Rev E
EN2342QI
Thermal Considerations
Thermal considerations are important power supply
design facts that cannot be avoided in the real
world. Whenever there are power losses in a
system, the heat that is generated by the power
dissipation needs to be accounted for. The Altera
Enpirion PowerSoC helps alleviate some of those
concerns.
For VIN = 12V, VOUT = 3.3V at 4A, η ≈ 91%
η = POUT / PIN = 91% = 0.91
PIN = POUT / η
PIN ≈ 13.2W / 0.9 ≈ 14.51W
The power dissipation (PD ) is the power loss in the
system and can be calculated by subtracting the
output power from the input power.
The Altera Enpirion EN2342QI DC-DC converter is
packaged in an 8x11x3mm 68-pin QFN package.
The QFN package is constructed with copper lead
frames that have exposed thermal pads. The
exposed thermal pad on the package should be
soldered directly on to a copper ground pad on the
printed circuit board (PCB) to act as a heat sink.
The recommended maximum junction temperature
for continuous operation is 125°C. Continuous
operation above 125°C may reduce long-term
reliability. The device has a thermal overload
protection circuit designed to turn off the device at
an approximate junction temperature value of
150°C.
With the power dissipation known, the temperature
rise in the device may be estimated based on the
theta JA value (θJA). The θJA parameter estimates
how much the temperature will rise in the device for
every watt of power dissipation. The EN2342QI has
a θJA value of 18 ºC/W without airflow.
The EN2342QI is guaranteed to support the full 4A
output current up to 85°C ambient temperature.
The following example and calculations illustrate
the thermal performance of the EN2342QI.
Example:
ΔT ≈ 1.31W x 18°C/W = 23.5°C ≈ 24°C
The junction temperature (T J ) of the device is
approximately the ambient temperature (T A) plus
the change in temperature. We assume the initial
ambient temperature to be 25°C.
VIN = 12V
T J = T A + ΔT
VOUT = 3.3V
T J ≈ 25°C + 24°C ≈ 49°C
The maximum operating junction temperature
(T JMAX) of the device is 125°C, so the device can
operate at a higher ambient temperature. The
maximum ambient temperature (T AMAX) allowed can
be calculated.
T AMAX = T JMAX – PD x θJA
IOUT = 4A
First calculate the output power.
POUT = 3.3V x 4A = 13.2W
Next, determine the input power based on the
efficiency (η) shown in Figure 9.
Determine the change in temperature (ΔT) based
on PD and θJA.
ΔT = PD x θJA
The maximum ambient temperature the device can
reach is 101°C given the input and output
conditions. Note that the efficiency will be slightly
lower at higher temperatures and this calculation is
an estimate.
90
EFFICIENCY (%)
≈ 14.51W – 13.2W ≈ 1.31W
≈ 125°C – 24°C ≈ 101°C
Efficiency vs. Output Current
100
91%
80
PD = PIN – POUT
70
60
50
40
30
20
VOUT = 3.3V
10
CONDITIONS
VIN = 12.0V
0
0
0.5
1
1.5
2
2.5
OUTPUT CURRENT (A)
3
3.5
4
Figure 9: Efficiency vs. Output Current
www.altera.com/enpirion, Page 18
09520
March 5, 2015
Rev E
EN2342QI
Engineering Schematic
Figure 10: Engineering Schematic with Engineering Notes
www.altera.com/enpirion, Page 19
09520
March 5, 2015
Rev E
EN2342QI
Layout Recommendation
Figure 11: Top Layer Layout with Critical Components
(Top View). See Figure 10 for corresponding schematic.
This layout only shows the critical components and
top layer traces for minimum footprint in singlesupply mode. Alternate circuit configurations &
other low-power pins need to be connected and
routed according to customer application. Please
see the Gerber files at www.altera.com for details
on all layers.
Recommendation 1: Input and output filter
capacitors should be placed on the same side of
the PCB, and as close to the EN2342QI package
as possible. They should be connected to the
device with very short and wide traces. Do not use
thermal reliefs or spokes when connecting the
capacitor pads to the respective nodes. The +V and
GND traces between the capacitors and the
EN2342QI should be as close to each other as
possible so that the gap between the two nodes is
minimized, even under the capacitors.
Recommendation 2: The PGND connections for
the input and output capacitors on layer 1 need to
have a slit between them in order to provide some
separation between input and output current loops.
Recommendation 3: The system ground plane
should be the first layer immediately below the
surface layer. This ground plane should be
continuous and un-interrupted below the converter
and the input/output capacitors.
Recommendation 4: The thermal pad underneath
the component must be connected to the system
ground plane through as many vias as possible.
The drill diameter of the vias should be 0.33mm,
and the vias must have at least 1 oz. copper plating
on the inside wall, making the finished hole size
around 0.20-0.26mm. Do not use thermal reliefs or
spokes to connect the vias to the ground plane.
This connection provides the path for heat
dissipation from the converter.
Recommendation 5: Multiple small vias (the same
size as the thermal vias discussed in
recommendation 4) should be used to connect
ground terminal of the input capacitor and output
capacitors to the system ground plane. It is
preferred to put these vias along the edge of the
GND copper closest to the +V copper. These vias
connect the input/output filter capacitors to the
GND plane, and help reduce parasitic inductances
in the input and output current loops. If vias cannot
be placed under the capacitors, then place them on
both sides of the slit in the top layer PGND copper.
Recommendation 6: AVIN is the power supply for
the small-signal control circuits. AVINO powers
AVIN in single supply mode. AVIN and AVINO
should have a decoupling capacitor close to each
of their pins. Refer to Figure 11.
Recommendation 7: The layer 1 metal under the
device must not be more than shown in Figure 11.
Refer to the section regarding Exposed Metal on
Bottom of Package. As with any switch-mode
DC/DC converter, try not to run sensitive signal or
control lines underneath the converter package on
other layers.
Recommendation 8: The VOUT sense point should
be just after the last output filter capacitor. Keep the
sense trace short in order to avoid noise coupling
into the node. Contact Altera MySupport for any
remote sensing applications.
Recommendation 9: Keep RA, CA, RB, and RCA
close to the VFB pin (Refer to Figure 11). The VFB
pin is a high-impedance, sensitive node. Keep the
trace to this pin as short as possible. Whenever
possible, connect RB directly to the AGND pins 52
and 53 instead of going through the GND plane.
Recommendation 10: Follow all the layout
recommendations as close as possible to optimize
performance. Altera provides schematic and layout
reviews for all customer designs. Contact Altera
MySupport
for
detailed
support
(www.altera.com/mysupport).
www.altera.com/enpirion, Page 20
09520
March 5, 2015
Rev E
EN2342QI
Design Considerations for Lead-Frame Based Modules
Exposed Metal on Bottom of Package
Lead-frames offer many advantages in thermal performance, in reduced electrical lead resistance, and in
overall foot print. However, they do require some special considerations.
In the assembly process lead frame construction requires that, for mechanical support, some of the lead-frame
cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several
small pads being exposed on the bottom of the package, as shown in Figure 12.
Only the thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board.
The PCB top layer under the EN2342QI should be clear of any metal (copper pours, traces, or vias) except for
the thermal pad. The “shaded-out” area in Figure 12 represents the area that should be clear of any metal on
the top layer of the PCB. Any layer 1 metal under the shaded-out area runs the risk of undesirable shorted
connections even if it is covered by soldermask.
The solder stencil aperture should be smaller than the PCB ground pad. This will prevent excess solder from
causing bridging between adjacent pins or other exposed metal under the package. Please consult the
Enpirion Manufacturing Application Note for more details and recommendations.
Figure 12: Lead-Frame exposed metal (Bottom View)
Shaded area highlights exposed metal that is not to be mechanically or electrically connected to the PCB.
www.altera.com/enpirion, Page 21
09520
March 5, 2015
Rev E
EN2342QI
Recommended PCB Footprint
Figure 13: EN2342QI PCB Footprint (Top View)
The solder stencil aperture for the thermal pad (shown in blue) is based on Altera’s manufacturing recommendations
www.altera.com/enpirion, Page 22
09520
March 5, 2015
Rev E
EN2342QI
Package and Mechanical
Figure 14: EN2342QI Package Dimensions (Bottom View)
Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html
Contact Information
Altera Corporation
101 Innovation Drive
San Jose, CA 95134
Phone: 408-544-7000
www.altera.com
© 2014 Altera Corporation—Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX
words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as
trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor
products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without
notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in
writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for
products or services.
www.altera.com/enpirion, Page 23
09520
March 5, 2015
Rev E