Technical Data Safety switch Series SHS3 - ASI Description Article number ASI SHS3 SA R 6073200011 Swivel range: 0° … 270° 270° 0° 180° FR2 FR1 90° FA Operating diagram 9° 6° 3° 1.5 Nm Point of fixation 3° 6° 9° 1.5 Nm On Off Tolerances Switching angle (N.C.) + / - 1,5 ° Tolerances Forced disconnect torque 10% Tolerances Forced disconnect angle + / - 1,5 ° Point of fixation is in range of 0° ... 270° free selectable. The data refer to a SHS3 with fixed switching point Electrical Data Operating voltage Operating current AS-i Specifications AS-i Inputs Parameter bits AS-i Address U I 26,5 … 31,6 V; via AS-interface, reverse-polarity proof < 30 mA Profile S-0.B IO-Code: 0x0 ID-Code: 0xB ID-Code1: 0xF ID-Code2: 0xE Contact 1: Date bits D0/D1 = static 00 or dynamic code transmission Contact 2: Date bits D2/D3 = static 00 or dynamic code transmission no function preset address: 0 This document will not become the contractual basis; the details included herein do not constitute any descriptions of expected conditions, so that warranties/claims for defects on account of possible variations of the actual qualities from the qualities described herein are explicitly excluded. All rights reserved. Specifications subject to change without notice! Date of issue: 04.08.2011 / Page 1 of 2 Document : 6073200011_en / Last update: 2 / 2388-11 Bernstein AG, Tieloser Weg 6, D-32457 Porta Westfalica / www.bernstein.eu Vorlage : 0850174285 Orig. 2 Technical Data Safety switch Mechanical Data Switch Hinge Indication Ambient temperature Contact type Mechanical life Switching frequency Mounting Connection Plug connection Weight Mounting position Protection class Switching angle Forced disconnect angle Forced disconnect torque Mechanical load (Forces see the illustration page 1) PBT Cast stainless steel LEDs for slave and bus state -25°C to +70°C (connecting cable permanently mounted; no freezing over / no condensation) 2 NC (slow-action, Zb) 106 operations Max. 300 operations/h 4 x M6 screws DIN EN ISO 7984 on flat and stiff ground Plug connector M12 male 1: AS-i + 2: free 3: AS-i 4: free ≈ 0,65 kg any IP 67 acc. IEC/EN 60529 +/- 3° from fixation point for the N.C. contacts and 9° for the N.O. contact 6° +2° from fixation point in both directions (for 0°-3° only in Plus-direction, for 267°-270° only in Minus-direction) 1,5 Nm FR1= max. 1200 N FR2= max. 500 N FA = max. 1200 N Standards VDE 0660 T100, DIN EN 60947-1, IEC 60947-1 VDE 0660 T200, DIN EN 60947-5-1, IEC 60947-5-1 EN 50295, EN ISO 13849-1 EU-Conformity acc. to EMC Directive Safety Classification according 13849-1 to PL e MTTFd = high PFD = 2,49 * 10-10 Notes The safety guard shall always be mounted using two SHS3 at least! See max. load. If the risk assessment of the machine permits a single-channel monitoring a blank hinge can used as bearing element. High forces, unfavourable force application as well as dynamic loads can shorten the service life. In case that the SHS3 is used at an ambient temperature of 70° an accelerated ageing of the connecting cable can occur. The connecting cable shall be protected against mechanical damages. The installation of the connecting cable can be done via pipes or cable ducts. The manufacturer / supplier of the machine / equipment is obliged to take the applicable standards for the calculation of the safety distances of separating safety guards to hazardous areas into account. Especially these standards apply: EN 349, EN 953, EN 1088, DIN EN ISO 13857, ... . The switch shall not be used as a mechanical stop. This document will not become the contractual basis; the details included herein do not constitute any descriptions of expected conditions, so that warranties/claims for defects on account of possible variations of the actual qualities from the qualities described herein are explicitly excluded. All rights reserved. Specifications subject to change without notice! Date of issue: 04.08.2011 / Page 2 of 2 Document : 6073200011_en / Last update: 2 / 2388-11 Bernstein AG, Tieloser Weg 6, D-32457 Porta Westfalica / www.bernstein.eu Vorlage : 0850174285 Orig. 2