CLD-DS58 Rev 4C Product family data sheet Cree® XLamp® XM-L Color LEDs Product Description FEATURES Table of Contents The XLamp® XM-L Color LED is a multi- • Available in red, green, blue and white Characteristics - Complete Package......2 color LED that provides high lumen output in a single 5 mm x 5 mm package Characteristics - Per LED Die..................2 in a small package. Compared to discrete • Maximum drive current per LED die: Flux Characteristics.................................3 LEDs, XLamp XM-L Color LEDs reduce 1 A Relative Spectral Power Distribution......3 the distance between LED die, creating a • Individually addressable LEDs Relative Flux vs Junction Temperature...4 small optical source for excellent optical • Reflow solderable – JEDEC J-STD-020 Electrical Characteristics.........................4 control and efficient color mixing. XLamp • Electrically neutral thermal path Relative Flux vs. Current..........................5 XM-L Color LEDs can reduce LED system • RoHS-compliant Typical Spatial Distribution......................5 complexity by reducing the number of Bin and Order Code Formats...................6 components required. Performance Groups – Brightness.........6 Performance Groups – Chromaticity......7 Cree XLamp XM-L Color LEDs bring high Performance Groups – Dominant performance and quality of light to a wide Wavelength...............................................7 range of lighting applications, including Standard Order Codes and Bins..............8 color-changing lighting, stage lighting, Reflow Soldering Characteristics............9 architectural lighting, indoor directional Notes......................................................10 lighting, and entertainment lighting. Mechanical Dimensions........................11 Tape and Reel.........................................12 www.cree.com/Xlamp Packaging...............................................13 Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® XM-L Color LED Characteristics - Complete Package The following table lists the product characteristics for the XLamp XM-L Color LED package, measured with all LED dies on simultaneously and each LED die connected to independent drive circuits at 350 mA. Characteristics Unit Thermal resistance, junction to solder point °C/W 3.5 degrees (°) 130 Viewing angle (FWHM) Minimum Typical Maximum ESD withstand voltage (HBM per Mil-Std-883D) V 8000 LED junction temperature °C 150 Characteristics - Per LED Die The following table lists the product characteristics for each LED die within the XLamp XM-L Color LED package. Characteristics Unit Minimum Typical Temperature coefficient of voltage - red mV/°C -1.8 Temperature coefficient of voltage - green mV/°C -4 Temperature coefficient of voltage - blue, white mV/°C -3 DC forward current - red, green, blue, white mA Maximum 1000 Forward voltage (@ 350 mA, 25 °C) - red V 2.25 2.6 Forward voltage (@ 350 mA, 25 °C) - green V 3.3 3.9 Forward voltage (@ 350 mA, 25 °C) - blue, white V 3.1 3.7 Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 2 XLamp ® XM-L Color LED Flux Characteristics, (TJ = 25 °C) The following tables provide several base order codes for XM-L Color LEDs. For a complete description of the order code nomenclature, please refer to the Bin and Order Code Formats section (page 6). Color + Cool White Color + Neutral White Minimum Luminous Flux @ 350 mA CCT / Dominant Wavelength Range Color Min. Max. Group Red 620 nm 630 nm Green 520 nm 535 nm Blue 450 nm 465 nm Cool White 5700 K 8000 K 100 Red 620 nm 630 nm 45.7 Green 520 nm 535 nm Blue 450 nm 465 nm Neutral White 3700 K 4300 K Order Code Flux (lm) 45.7 87.4 C3 13.9 87.4 C2 13.9 XMLCTW-A0-0000-00C3AAAA1 XMLCTW-A0-0000-00C2AAAB1 80 Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±1 nm on dominant wavelength measurements. See the Measurements section (page 10). • Flux and chromaticity are measured with each LED die connected to independent drive circuits at 350 mA. The flux and chromaticity of each LED die within the XLamp XM-L Color LED package are measured individually. Relative Spectral Power Distribution (If = 350 mA per LED) The following graph represents typical spectral output of the XM-L RGBW Color LED with each LED on independently. Relative Spectral Power Distribution (IF = 350 mA per LED Die, 25 °C) The following graph represents typical spectral output of the XLamp XM-L Color LED with each LED die on independently. Relative Radiant Power 100% 80% Red 60% Green Blue 40% White 4000 K White 6000 K 20% 0% 380 430 480 530 580 630 680 730 780 Wavelength (nm) Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 3 XLamp ® XM-L Color LED Relative Flux Output vs. Junction Temperature (If = 350 mA) The following graph represents typical performance of each LED die in the XM-L RGBW LED Relative Flux vs Junction Temperature (IF = 350 mA) The following graph represents typical performance of each LED die in the XLamp XM-L Color LED. Relative Luminous Flux 100% 80% Red 60% Green Blue 40% White 20% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Electrical Characteristics (Tj = 25ºC) Electrical (TJperformance = 25 ˚C) The followingCharacteristics graph represents typical of each LED die in the XM-L RGBW LED The following graph represents typical performance of each LED die in the XLamp XM-L Color LED. 1000 900 Forward Current (mA) 800 700 600 Red 500 Green Blue, White 400 300 200 100 0 2.0 2.5 3.0 3.5 4.0 Forward Voltage (V) Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 4 XLamp ® XM-L Color LED Relative Intensity vs. Current (Tj = 25ºC) Relative Flux vs. Current (T = 25 ˚C) J The following graph represents typical performance of each LED die in the XLamp XM-L Color LED. 300% Relative Luminous Flux 250% 200% Red Green 150% Blue White 100% 50% 0% 0 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Typical Spatial Distribution Typical Spatial Radiation Pattern The following graph represents typical spectral output of the XLamp MC-E LED with all four LEDs on simultaneously. The following graph represents typical output of the XLamp XM-L Color LED with all four LEDs on simultaneously. 100% Relative Luminous Intensity 80% 60% 40% 20% -90 -60 -30 0% 0 30 60 90 Angle (º) Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 5 XLamp ® XM-L Color LED Bin and Order Code Formats Bin codes and order codes are configured in the following manner: Series XML = XML Color CTW = Red, green, blue, white Reel size Internal code Dominant wavelength kit (RGB) Order Code SSSCCC-BD-HHHH-NNNNNNNNN Bin Code Chromaticity kit for white Flux kit Internal code Package configuration A = Individually addressable Series XML = XML Color CTW = Red, green, blue, white Dominant wavelength bin for each die (RGB) Internal code SSSCCC-B-HHHH-NNNMMKKKK Chromaticity bin for white die Flux bin for each die (RGBW) Package configuration A = Individually addressable Performance Groups – Brightness Each LED die in the XLamp XM-L Color LED is tested individually for luminous flux and placed into one of the following luminous-flux groups. Color Red Green Blue White Group Code Minimum Luminous Flux (lm) @ 350 mA Maximum Luminous Flux (lm) @ 350 mA) M 45.7 87.4 N 87.4 114 N 87.4 114 P 114 148 F 13.9 39.8 2 80 100 3 100 120 4 120 140 • Flux and chromaticity are measured with each LED die connected to independent drive circuits at 350 mA. Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 6 XLamp ® XM-L Color LED Performance Groups – Chromaticity (IF = 350 ma Per LED Die) The white LED die in the XLamp XM-L Color LED is individually tested for chromaticity at 350 mA and placed into one of the regions defined by the bounding coordinates shown below. Region WM WB WE WN Region 5A x y .3670 .3702 .3825 .3798 .3783 .3646 x y .295 .297 x y .316 .332 .308 .311 .310 .300 .317 .319 .308 .298 .311 .288 .306 .322 .306 .322 .314 .355 .308 .311 .316 .332 .295 .297 .306 .322 .292 .306 .301 .342 .301 .342 .329 .345 .306 .322 .329 .330 .292 .306 .317 .319 .287 .321 .316 .332 .308 .311 .329 .369 .317 .319 .329 .345 .318 .308 .316 .332 .310 .300 .314 .355 Region Region x y .3578 .3702 .3722 .3736 .3869 .3958 .3825 .3798 5B WC WF WD WG Region x y .3722 .3825 .3874 .3869 .4006 .4044 .3950 .3875 5C Region x y .3798 .3783 .3646 .3958 .3825 .3798 .3950 .3875 .3898 .3716 5D Performance Groups – Dominant Wavelength The red, green and blue LED dies in the XLamp XM-L Color LED are tested individually for dominant wavelength (DWL) and sorted into one of the DWL bins defined below. Color Blue DWL Group Minimum DWL @ 350 mA Maximum DWL @ 350 mA K 450 455 L 455 460 M 460 465 2 520 525 Green 3 525 530 4 530 535 Red A 620 630 Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 7 XLamp ® XM-L Color LED Standard Order Codes and Bins The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s color or chromaticity bins and luminous flux range. XLamp XM-L Color LED Standard Order Codes Minimum Luminous Flux (lm) @ 350 mA* Color Group Flux (lm) DWL / Chromaticity Bins Kit Number Red M 45.7 A Green N 87.4 2, 3, 4 Blue F 13.9 K, L, M WC, WD, WF, WG, WB, WE, WM, WN 00C3AAAA1 White 3 100 Red M 45.7 A Green N 87.4 2, 3, 4 Blue F 13.9 K, L, M White 2 80 5A, 5B, 5C, 5D 00C2AAAB1 For other flux and chromaticity combinations, contact Cree or an authorized distributor. * Cree XLamp XM-L Color LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity or DWL bin restrictions specified by the order code. 0.45 0.44 3000 K 0.43 0.42 3500 K 0.41 4000 K 0.40 4500 K 0.37 CCy B15D 6A 6D 7A 7D 8A 8B 8C 8D 4B 5A 5700 K WH 3C 4D 3B 4A 6500 K 3D WG 3A WJ 0.36 0.35 0.34 WF 8000 K WD WE A1 WC 0.33 0.32 0.31 4C 0.40 5000 K 0.38 5C 5B 0.38 0.39 7B 6C 6B 7C 2700 K 10000 K 0.30 WB WA 0.29 WP WN WM WK 0.28 0.50 0.49 0.48 0.47 0.46 0.45 0.44 0.43 0.42 0.41 0.39 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.26 0.27 CCx Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 8 XLamp ® XM-L Color LED Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L Color LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Time Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) 217 °C 45-90 seconds Peak/Classification Temperature (Tp) 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 9 XLamp ® XM-L Color LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 10 6 5 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND 6 5 OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY NOTICE UNAUTHORIZED PERSON THE WITHOUT WRITTEN CONSENT CREE CONFIDENTIAL.OF THIS PLOT AND THE INFORMATION CREE INC. CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON THE WITHOUT WRITTEN CONSENT OF CREE INC. 4 3 4 3 XLamp D D ® A REVIS B XM-L REV Color LEDDESCRIPTION C A INITIAL RELEASE B ADDED ANODE SIGN TO IS C CORRECTED DOME RA Mechanical Dimensions Thermal vias, if present, are not shown on these drawings. 4.78 5.000 .500 indicated. All measurements are ±.13 mm unless otherwise 4.78 5.000 8 1 5.000 7 C 5.000 6 D1 D2 D4 D3 6 5 .500 1 7 8 C REV 2 2 D1 D2 D4 D3 2 1.01 3 1.01 TOP VIEW R2.26 COLOR D1: RED D2: GREEN D3: BLUE D4: WHITE D6 (-) 3 NEGATIVE 2 6 3 5 D4 5 2.78 7 D3 D7 (-) 4 NEGATIVE .50 1 D2 7 6 NEGATIVE (-) 4 A .50 1 D5 POSITIVE (+) 1 D2 2 D6 POSITIVE (+) 2 D3 3 D7 POSITIVE (+) 3 D4 4 D8 6 1.01 5 5 .250 .50 .500 .500 .500 BOTTOM VIEW POSITIVE (+) 2 POSITIVE (+) 3 .80 .80 1.01 1.01 4.78 4 DR UNLESS OTHERWISE SPEC D. DIMENSIONS ARE IN INCHE AND AFTER FINISH. CH TOLERANCE UNLESS SPEC ± .01 DATE DRAWN.XX BY AP UNLESS OTHERWISE SPECIFIED .XXX ± .005 D. CRONIN 8/29/12 DIMENSIONS ARE IN INCHES X° ± .5° CHECK DATE THIRD PROJECTION AND ANGLE AFTER FINISH. MA FOR SHEET METAL PARTS TOLERANCE UNLESS SPECIFIED: .X ± .06 .XX ± .01 APPROVED .XXDATE ± .03 .XXX± .005 .XXX± .010TITLE FIN X° ± .5° X° ± .5° THIRD ANGLE PROJECTION .50 XML MATERIAL .50 FOR SHEET METAL PARTS ONLY 63 SURFACE FINISH: .25 ± .06 .25 .X SIZE .XX ± .033 4 .XXX± .010 FINAL PROTECTIVE FINISH C X° ± .5° SCALE 63 16.00 SURFACE .80FINISH: POSITIVE (+) 4 5 5 .80 3 4.78 2 .25 4.78 .25 1.01 4.78 1.0 POSITIVE (+) 1 2.78 .25 4.78 6 BOTTOM VIEW D8 POSITIVE (+) 4 4 6 6 4 SIDE VIEW .500 D1 8 D1 D5 (-) 2 NEGATIVE A 7 2.782 8 NEGATIVE (-) 3 1.01 4 SIDE VIEW NEGATIVE (-) 1 COLOR D1: RED D2: GREEN NEGATIVE (-) 2 D3: BLUE D4: WHITE 3 3.02 3.02 Anode B 7 .500 2.782 R2.26 NEGATIVE (-) 1 2 3 4 B 1.01 4.78 4 TOP VIEW 8 2 4.78 3 5 1.01 1 1.0 8 1 4.78 Recommended PCB Solder Pad .25 .25 1.01 .97 4.78 .25 .97 4.78 Recommended Stencil Pattern (Shaded Area Is Open) Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 11 6 5 4 3 2.00[.079] 4.00[.157] 1 2 REVISIONS NOTICE EE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NTAINED WITHIN ARE THE PROPRIETARY AND NFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT Y NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY AUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT CREE INC. DESCRIPTION REV BY DATE APP'D POCKET SIZE +.10 +.0039 .0591 -.00 -.0000 [ ] Do1.50 P2 1.75[.069] E1 Po Ao - 5.40mm [.213"] Bo - 5.40mm [.213"] Ko - 3.35mm [.132"] Tape and Reel 3.0° XLamp ® XM-L Color LED D 5.40[.213] Bo 3 12.00[.472] Component Handling Systems Standard. All Cree carrier tapes conform to EIA-481D, Automated 6 5 4 5.50[.217]F 6 5 4 NOMINAL C NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THETHIS PROPRIETARY ANDINFORMATION CREE CONFIDENTIAL. PLOT AND THE CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN AREOF THE PROPRIETARY AND MAY NOT BE COPIED, INFORMATION REPRODUCEDOF ORCREE, DISCLOSED TO PLOT ANY CONFIDENTIAL INC. THIS UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. D D REV 12.30 [.484] MAX W 10.25 [.404] E2 2.00[.079] 2.00[.079] P2 1.50[.059] 4.00[.157] D1 4.00[.157] Po 8.00[.315] P 2 3 REVISIONS REVISIONS DESCRIPTION DESCRIPTION 6 5 C NOTICE NTIAL. THIS PLOT AND THE INFORMATION THIN ARE THE PROPRIETARY AND INFORMATION OF CREE, INC. THIS PLOT OPIED, REPRODUCED OR DISCLOSED TO ANY D PERSON WITHOUTTHE WRITTEN CONSENT 5.40[.213] 4 3.0° A B Ao B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 X° ± .5 ° SURFACE FINISH: 5 4 8 6 1 C BY DATE DDS 11/8/10 DC 2/26/12 BS 8.00[.315] DATE 8.00[.315] P TITLE P APPROVED SIZE A Loaded Pockets (1000 Lamps) A FINAL PROTECTIVE FINISH User Feed Direction REV. DRAWING NO. 2402-00011 7.0° SCALE DRAWING SCALE 2 SHEET 7.0° 1 A OF 4 1.75 3.35[.132] 3.35[.132] 3 Ko Ko START 12 .36[.014] D T .36[.014] T A XM 5050 CARRIER TAPE MATERIAL 5.40[.213] 5.40[.213] Ao ANODE SIDE 1.50[.059] Phone (919) 313-5300 Fax (919) 313-5558 D1 1.50[.059] D1 B 3.35 2 1 2400-00009 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 INDEX QTY ITEM 1 1 2400-00009-CORE DRAWN BY COMMENTS DATE UNLESS OTHERWISE SPECIFIED DATE 4/23/10 2 D. CRONIN 2DRAWN BY2400-00009-REEL UNLESS ARE OTHERWISE SPECIFIED DIMENSIONS IN INCHES D. CRONIN 4/23/10 DATE DIMENSIONS ARE IN INCHESCHECK AND AFTER FINISH. CHECK DATE AND AFTERSPECIFIED: FINISH. TOLERANCE UNLESS TOLERANCE .XX ± UNLESS .01 SPECIFIED: APPROVED DATE TITLE .XX ± .01 .XXX ± .005 APPROVED DATE TITLE X° ±.XXX .5± ° .005 THIRD ANGLE PROJECTION MATERIAL X° PARTS ± .5 ° FOR SHEET METAL ONLY Leader THIRD ANGLE PROJECTION MATERIAL FOR.XSHEET ± METAL .06 PARTS ONLY DRAWING NO. 400mm (min.) of SIZE .XX .X ± ±.03 .06 DRAWING NO. SIZE FINAL PROTECTIVE FINISH ± .03 empty pockets with .XXX .XX ± .010 FINAL PROTECTIVE FINISH X° ±.XXX .5± ° .010 at least 100mm SCALE X° ± .5 ° SURFACE FINISH: 63 SCALE sealed by tape DRAWING SCALE SURFACE FINISH: 63 DRAWING SCALE Ao C 4600 Silicon Drive Durham, N.C 27703 4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Phone (919) 313-5300 Fax (919) 313-5558 Fax (919) 313-5558 XMXM 5050 CARRIER TAPE 5050 CARRIER TAPE 2402-00011 A 2402-00011 A 6 (405 empty pockets min.) 4 5 3 4 2 3 A REV. A 6 SHEET OF SHEET 1 2 1OF / 1 1 D REV. A 1 /1 12.4 +.2 .0 MEASURED AT HUB C C 330 +.25 -.75 16.4 +0.2 .0 MEASURED AT HUB THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 5 4 1.6 3 1.9±.4 DATE DRAWN BY D. CRONIN CHECK 21 ±.4 4600 Silicon Drive Durham, N.C 27703 06/08/10 DATE -- Phone (919) 313-5300 -- Fax (919) 313-5558 A DATE APPROVED -- -- MATERIAL TITLE 13.1 ±.2 -- SIZE FINAL PROTECTIVE FINISH -- SCALE XM LOADING SPEC REV. DRAWING NO. C 2402-00012 SHEET 3.000 2 B OF B 1 /1 1 12.4 +1.0 -.5 MEASURED AT EDGE 60° 60° REVISONS REV DESCRIPTION BY DATE APP'D Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UNLESS OTHERWISE SPECIFIED DRAWN BY A THIRD ANGLE PROJECTION B 1 /1 B B C APP'D 4600 Silicon Drive Durham, N.C 27703 4/23/10 DATE CATHODE SIDE 4 5 Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) D. CRONIN CHECK 3 A 6 D DATE DRAWN BY 63 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. D D CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 B END 2 APP'D DATE APP'D 5.40[.213] 5.40[.213] Bo Bo 3.0° 12.00[.472] 12.00[.472] NOMINAL NOMINAL REVISONS [.484] 10.25 12.30DESCRIPTION 12.30 [.484] MAX Loaded pocket count was 750 [.404]10.25 MAX [.404] WANODE E2 MADE CATHODE AND W NOTE LARGER E2 REV 3.35[.132] Ko THIRD ANGLE PROJECTION 6 5.50[.217]F 5.50[.217]F 3 C BY DATE BoBo - - 5.40mm [.213"] 5.40mm [.213"] KoKo - - 3.35mm [.132"] 3.35mm [.132"] B 7.0° BY POCKET SIZE POCKET SIZE AoAo - - 5.40mm [.213"] 5.40mm [.213"] 1.75[.069] E1 1.75[.069] E1 .36[.014] T Po 1 All dimensions in mm. REV +.10 +.0039 Do1.50 .0591 +.0039 -.00 +.10 .0591 -.0000 [] Do1.50 -.00 -.0000 [ ] P2 1 2 DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° FOR SHEET METAL PARTS ONLY D. CRONIN CHECK DATE 4600 Silicon Drive Durham, N.C 27703 09/29/09 12 DATE -APPROVED -MATERIAL Phone (919) 313-5300 -- Fax (919) 313-5558 DATE -- TITLE REEL, 13" X 12MM, 3 PIECE SNAP A A XLamp ® XM-L Color LED Packaging Humidity Indicator Card (inside bag) Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. 13