5962-09216

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Add device type 10. Table II, add note to Group C end-point test
parameters. -gz
09-07-17
Charles F. Saffle
B
Add case outline M. Paragraph 1.5, add " ≥ " to 300 Krads (Si). (2
places) -gz
11-04-11
Charles F. Saffle
REV
SHEET
REV
B
B
B
B
B
B
B
SHEET
15
16
17
18
19
20
21
REV STATUS
REV
B
B
B
B
B
B
B
B
B
B
B
B
B
B
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Gary Zahn
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
CHECKED BY
Greg Cecil
APPROVED BY
Joseph D. Rodenbeck
DRAWING APPROVAL DATE
09-04-28
AMSC N/A
REVISION LEVEL
B
MICROCIRCUIT, HYBRID, LINEAR, POSITIVE,
LOW DROPOUT, ADJUSTABLE AND FIXED
VOLTAGE REGULATOR
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
1 OF
5962-09216
21
5962-E290-11
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962



Federal
stock class
designator
\
F



RHA
designator
(see 1.2.1)
\/
Drawing number
09216
/
01



Device
type
(see 1.2.2)
K



Device
class
designator
(see 1.2.3)
X



Case
outline
(see 1.2.4)
X



Lead
finish
(see 1.2.5)
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device types. The device types identify the circuit function as follows:
Device type
01
02
03
04
05
06
07
08
09
10
Generic number
MSK 5800RH
MSK 5810RH
MSK 5821RH
MSK 5820-1.5RH
MSK 5820-1.9RH
MSK 5820-2.5RH
MSK 5820-2.8RH
MSK 5820-3.3RH
MSK 5820-5.0RH
MSK 5820-1.8RH
Circuit function
Radiation hardened, 4.0 A adjustable voltage regulator
Radiation hardened, 5.0 A adjustable voltage regulator
Radiation hardened, 5.0 A adjustable voltage regulator
Radiation hardened, 5.0 A, 1.5 V voltage regulator
Radiation hardened, 5.0 A, 1.9 V voltage regulator
Radiation hardened, 5.0 A, 2.5 V voltage regulator
Radiation hardened, 5.0 A, 2.8 V voltage regulator
Radiation hardened, 5.0 A, 3.3 V voltage regulator
Radiation hardened, 5.0 A, 5.0 V voltage regulator
Radiation hardened, 5.0 A, 1.8 V voltage regulator
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
2
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
M
N
T
U
X
Y
Z
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
5
12
20
20
5
5
5
Package style
TO-254 with tab, gull wing leads, glass sealed
Flat pack with gull wing leads
Flat pack with straight leads
Flat pack with gull wing leads
TO-254 with tab, straight leads, glass sealed
TO-254 with tab, leads formed up, glass sealed
TO-254 with tab, leads formed down, glass sealed
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage (VIN) ......................................................................
Bias supply voltage (VBIAS)
Device type 02, only ...............................................................
Output current:
Device type 01........................................................................
Device types 02 through 10 ....................................................
Junction temperature (TJ) ..........................................................
Storage temperature ..................................................................
Lead temperature (soldering, 10 seconds) ................................
+10.0 V dc
+10.0 V dc
4.0 A 2/
5.0 A 2/
+150C
-65C to +150C
+300C
1.4 Recommended operating conditions.
Input voltage range (VIN)
Device type 01........................................................................
Device type 02........................................................................
Device types 03 through 10 ....................................................
Output current (minimum) ..........................................................
Output voltage range:
Device type 01........................................................................
Device type 02........................................................................
Device type 03........................................................................
Bias supply voltage (VBIAS)
Device type 02, only ...............................................................
Case operating temperature range (TC) .....................................
+2.9 V dc to +7.5 V dc
+2.0 V dc to +7.5 V dc
+2.9 V dc to +6.5 V dc
10 mA
+1.5 V dc to +6.8 V dc
+1.5 V dc to +7.0 V dc
+1.5 V dc to +6.0 V dc
+2.9 V dc to +7.5 V dc
-55C to +125C
1.5 Radiation features.
Maximum total dose available:
Device type 01........................................................................
Device types 02 through 10 ....................................................
1/
2/
3/
4/
5/
≥ 300 Krads (Si) 3/ 4/ 5/
≥ 300 Krads (Si) 3/ 4/ 5/
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
Output current limit is dependent on the value of VIN - VOUT .
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A.
Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device
types have not been characterized for displacement damage.
See figure 3.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
4
TABLE I. Electrical performance characteristics.
Test
Symbol
Feedback voltage
VFB
Conditions 1/ 2/ 3/
-55C  TC +125C
unless otherwise specified
Group A
subgroups
10 mA  IOUT  1.0 A, VOUT = 1.5 V
1,2,3
1/
M,D,P,L,R,F 1/
M,D,P,L,R
Quiescent current
IQ
VIN = 7.5 V
Max
01,02,
03
1.225
1.305
1
01,02,
03
1.225
1.305
1
01,02,
03
1.225
1.310
1,2,3
01
20
02
20
03-10
20
1,2,3
02
4
1
04-10
1.0
VIN = 6.5 V
IBIAS
VBIAS = 7.5 V
Output voltage
tolerance 4/
VOUTTOL
VIN = VOUT + 1 V, IOUT = 1.0 A
1/
1
04-10
2.1
M,D,P,L,R,F 1/
1
04-10
3.1
IOUT = 10 mA, 2.9 V  VIN  7.5 V,
VOUT = 1.5 V
1,2,3
01,02
0.50
IOUT = 50 mA,
VOUT + 0.4 V  VIN  VOUT + 1.3 V
1
03
0.50
M,D,P,L,R
VRLINE
1
mA
mA
%
%VOUT
2.5
2,3
IOUT = 50 mA,
VOUT + 0.4 V  VIN  VOUT + 1.3 V
V
2.5
2,3
Line regulation 4/
Unit
Min
IIN + IBIAS, VBIAS = VIN = 7.5 V
Bias current
Limits
Device
type
04-10
0.50
2.5
2,3
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
5
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Load regulation 4/
VRLOAD
Conditions 1/ 2/ 3/
-55C  TC +125C
unless otherwise specified
Group A
subgroups
10 mA  IOUT  1.0 A, VOUT = 2.5 V
1,2,3
01,02
0.80
50 mA  IOUT  3.0 A, VOUT = 2.5 V
1
03
0.80
Device
type
Limits
Min
1
VDO
Delta FB = 1%, IOUT = 1.0 A
2.5
1,2,3
Delta FB = 1%, IOUT = 2.5 A
Delta VOUT = 1%, IOUT = 2.5 A
Output current limit 6/
IOUT
VIN = 4.4 V, VOUT = 3.3 V
1
01
0.70
02
0.40
03
0.40
04-10
0.40
01
2,3
VIN = 2.5 V, VOUT = 1.5 V
%VOUT
0.80
04-10
2,3
Dropout voltage 5/
Max
2.5
2,3
50 mA  IOUT  3.0 A,
VIN = VOUT + 1 V
Unit
1
02
2,3
1.5
2.0
1.3
2.2
3.2
4.0
V
A
3.0
VIN = 3.5 V, VOUT = 2.5 V
1,2,3
03
3.0
5.0
VIN = VOUT + 1 V
Over-current latch up
1,2,3
04-10
3.0
5.0
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Shutdown threshold
VST
Conditions 1/ 2/ 3/
-55C  TC +125C
unless otherwise specified
Group A
subgroups
VOUT  0.2 V (OFF)
1,2,3
Device
type
All
VOUT = Nominal (ON)
Shutdown hysteresis
1/
2/
3/
4/
5/
6/
VSH
Difference between voltage
threshold of VSDI (ON) and
VSDI (OFF)
1,2,3
Limits
Unit
Min
Max
1.0
1.6
1.0
1.6
01,02
0.2
V
V
Device types 01 through 10 have been characterized through all levels M, D, P, L, R, and F of irradiation. However,
device types 01 through 10 are tested at 1.5 times the F level. Pre and post irradiation values are identical unless
otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TC = +25C.
Unless otherwise specified:
Device types 01 and 03; VIN = 5.0 V, VSHUTDOWN = 0 V, and IOUT = 10 mA.
Device type 02; VBIAS = VIN = 5.0 V, VSHUTDOWN = 0 V, and IOUT = 10 mA.
Device types 04 through 10; VIN = VOUT + 1 V, VSHUTDOWN = 0 V, and IOUT = 10 mA.
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition A.
Device types 03 through 10; VIN shall be as specified or VIN MIN, whichever is greater.
Device types 03 through 10; not applicable when VOUT  VIN MIN - dropout voltage maximum.
Output current limit is dependent upon the values of VIN and VOUT.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
7
Case outline M.
(Device types 03 through 10)
Symbol
A
A1
A2
øb
D
E
E1
e
e1
L
L1
L2
L3
øP
R
X
S1
Millimeters
Min
Max
--6.48
0.89
1.14
3.30
3.81
0.71
0.81
20.70
20.96
17.27
17.78
8.64
8.89
2.54 TYP
10.03
10.29
11.43
11.94
13.34
13.84
2.87
3.12
2.41
2.92
3.94
4.19
0.76
1.02
-0.25
0.25
3.68 REF
Inches
Min
Max
--.255
.035
.045
.130
.150
.028
.032
.815
.825
.680
.700
.340
.350
.100 TYP
.395
.405
.450
.470
.525
.545
.113
.123
.095
.115
.155
.165
.030
.040
-.010
.010
.145 REF
NOTES:
1. Leads shall be coplanar with the package base/seating plane.
2. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
3. Pin numbers are for reference only.
4. Case outline M weight: 7.7 grams typical.
FIGURE 1. Case outlines.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
8
Case outline N.
(Device type 01)
Symbol
A
A1
b
c
D/E
D1
D2
e
e1
L1/L2
S1
Millimeters
Min
Max
--4.06
0.13
0.64
0.25
0.51
0.13
0.38
16.62
16.13
20.70
21.21
18.16
18.67
2.54 TYP
12.45
12.95
1.02
1.52
1.59 REF
Inches
Min
Max
--.160
.005
.025
.010
.020
.005
.015
.615
.635
.815
.835
.715
.735
.100 TYP
.490
.510
0.040
0.060
.0625 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline N weight: 3.3 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
9
Case outline T.
(Device type 02)
Symbol
A
A1
b
c
D/E
e
e1
L1
S1
Millimeters
Min
Max
--3.94
1.80
2.31
0.25
0.51
0.13
0.38
16.62
16.13
1.27 TYP
11.18
11.68
12.70
--2.21 REF
Inches
Min
Max
--.155
.071
.091
.010
.020
.005
.015
.615
.635
.050 TYP
.440
.460
.500
--.087 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline T weight: 3.3 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
10
Case outline U.
(Device type 02)
Symbol
A
A1
b
c
D/E
D1
D2
e
e1
L1/L2
S1
Millimeters
Min
Max
--3.94
0.08
0.58
0.25
0.51
0.13
0.38
16.62
16.13
20.70
21.21
18.16
18.67
1.27 TYP
11.18
11.68
1.02
1.52
2.21 REF
Inches
Min
Max
--.155
.003
.023
.010
.020
.005
.015
.615
.635
.815
.835
.715
.735
.050 TYP
.440
.460
0.040
0.060
.087 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline U weight: 3.3 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
11
Case outline X.
(Device types 03 through 10)
Symbol
A
A1
A2
øb
D
E
E1
e
e1
L
L1
L2
øP
S1
Millimeters
Min
Max
--6.48
0.76
1.27
3.30
3.81
0.71
0.81
20.57
21.08
17.27
17.78
8.51
9.02
2.54 TYP
9.91
10.41
12.70
--13.34
13.84
2.74
3.25
3.81
4.31
3.68 REF
Inches
Min
Max
--.255
.030
.050
.130
.150
.028
.032
.810
.830
.680
.700
.335
.355
.100 TYP
.390
.410
.500
--.525
.545
.108
.128
.150
.170
.145 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline X weight: 7.7 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
12
Case outline Y.
(Device types 03 through 10)
Symbol
A
A1
A2
øb
D
E
E1
e
e1
L
L1
L2
L3
øP
S1
Millimeters
Min
Max
--6.48
0.76
1.27
3.30
3.81
0.71
0.81
20.57
21.08
17.27
17.78
8.51
9.02
2.54 TYP
9.91
10.41
4.70
5.46
13.34
13.84
2.74
3.25
8.38
--3.81
4.31
3.68 REF
Inches
Min
Max
--.255
.030
.050
.130
.150
.028
.032
.810
.830
.680
.700
.335
.355
.100 TYP
.390
.410
.185
.215
.525
.545
.108
.128
.330
--.150
.170
.145 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline Y weight: 7.7 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
13
Case outline Z.
(Device types 03 through 10)
Symbol
A
A1
A2
øb
D
E
E1
e
e1
L
L1
L2
L3
øP
S1
Millimeters
Min
Max
--6.48
0.76
1.27
3.30
3.81
0.71
0.81
20.57
21.08
17.27
17.78
8.51
9.02
2.54 TYP
9.91
10.41
4.70
5.46
13.34
13.84
2.74
3.25
8.38
--3.81
4.31
3.68 REF
Inches
Min
Max
--.255
.030
.050
.130
.150
.028
.032
.810
.830
.680
.700
.335
.355
.100 TYP
.390
.410
.185
.215
.525
.545
.108
.128
.330
--.150
.170
.145 REF
NOTES:
1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
2. Pin numbers are for reference only.
3. Case outline Z weight: 7.7 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
14
Device types
01
02
03
04 through 10
Case outlines
N
(12 pin)
T and U
(20 pin)
M, X, Y, Z
(5 pin)
M, X, Y, Z
(5 pin)
Terminal number
Terminal symbol
Terminal symbol
Terminal symbol
Terminal symbol
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
VIN A
VIN B
VIN C
GND 1
LATCH
SHUTDOWN
FEEDBACK (FB)
GND 2
GND 2
VOUT C
VOUT B
VOUT A
VIN A
VIN B
VIN C
VIN D
VIN E
VBIAS
GND 1
GND 1
LATCH
SHUTDOWN
FEEDBACK (FB)
GND 2
GND 2
GND 2
NO CONNECT
VOUT A
VOUT B
VOUT C
VOUT D
VOUT E
VIN
GND
VOUT
SHUTDOWN
ADJUST
VIN
GND
VOUT
SHUTDOWN
NO CONNECT
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
15
Device type 01.
FIGURE 3. Radiation exposure circuits.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
16
Device type 02.
FIGURE 3. Radiation exposure circuits - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
17
Device type 02 - Continued.
FIGURE 3. Radiation exposure circuits - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
18
Device type 03 through 10.
NOTE: Device type 03, pin 5 is ADJUST and device types 04 through 10, pin 5 is NO CONNECT.
FIGURE 3. Radiation exposure circuits - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
19
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
---
Final electrical parameters
1*, 2, 3
Group A test requirements
1, 2, 3
Group C end-point electrical
parameters 1/
1, 2, 3
End-point electrical parameters
for radiation hardness assurance
(RHA) devices
1
* PDA applies to subgroup 1.
1/ As a minimum, for all Group C testing performed after July 17, 2009
manufacturers shall perform subgroups 1, 2, and 3 from the Group A
electrical test table (Table C-Xa of MIL-PRF-38534).
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2)
TC = +125C minimum.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
Tests shall be as specified in table II herein.
b.
Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
20
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2)
TC = +125C minimum.
(3)
Test duration: 1,000 hours minimum as specified in 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA qualification is required for those devices with the RHA
designator as specified herein. End-point electrical parameters for radiation hardness assurance (RHA) devices shall be
specified in table II. Radiation testing will be in accordance with the qualifying activity (DLA Land and Maritime-VQ) approved
plan and with MIL-PRF-38534, Appendix G.
4.3.5.1 Total dose irradiation testing. Total dose irradiation testing shall be in accordance with MIL-STD-883 method 1019,
condition A and as specified herein. Sample testing in accordance with table I shall be performed on a representative device
type (similar device) at initial qualification and after any design or process changes which may affect the RHA response.
Sample size is a minimum of 8 devices (4 biased and 4 not biased). This sample testing is repeated for each new combination
for wafers of active elements on the most complex device.
a.
Similar device, in this application, means that if two or more device types have the same schematic function (same
active circuit design) and contain the same microcircuit and semiconductor elements, then the devices may be
considered similar and sample radiation testing would be performed on the device that is most complex of the similar
devices. The device types on this drawing are similar device types. Device type 5962F0921602 is considered the most
complex device.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used
for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962)
should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to
this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09216
A
REVISION LEVEL
B
SHEET
21
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 11-04-11
Approved sources of supply for SMD 5962-09216 listed below for immediate acquisition information only and shall be
added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate
of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is
superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an
online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962F0921601HNA
5962F0921601HNC
51651
51651
MSK 5800HRH
MSK 5800HRH
5962F0921601KNA
5962F0921601KNC
51651
51651
MSK 5800KRH
MSK 5800KRH
5962F0921602HTA
5962F0921602HTC
5962F0921602HUA
5962F0921602HUC
51651
51651
51651
51651
MSK 5810HRH
MSK 5810HRH
MSK 5810HRHG
MSK 5810HRHG
5962F0921602KTA
5962F0921602KTC
5962F0921602KUA
5962F0921602KUC
51651
51651
51651
51651
MSK 5810KRH
MSK 5810KRH
MSK 5810KRHG
MSK 5810KRHG
5962F0921603HMA
5962F0921603HMC
5962F0921603HXA
5962F0921603HXC
5962F0921603HYA
5962F0921603HYC
5962F0921603HZA
5962F0921603HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5821HRHGW
MSK 5821HRHGW
MSK 5821HRHS
MSK 5821HRHS
MSK 5821HRHU
MSK 5821HRHU
MSK 5821HRHD
MSK 5821HRHD
5962F0921603KMA
5962F0921603KMC
5962F0921603KXA
5962F0921603KXC
5962F0921603KYA
5962F0921603KYC
5962F0921603KZA
5962F0921603KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5821KRHGW
MSK 5821KRHGW
MSK 5821KRHS
MSK 5821KRHS
MSK 5821KRHU
MSK 5821KRHU
MSK 5821KRHD
MSK 5821KRHD
5962F0921604HMA
5962F0921604HMC
5962F0921604HXA
5962F0921604HXC
5962F0921604HYA
5962F0921604HYC
5962F0921604HZA
5962F0921604HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.5HRHGW
MSK 5820-1.5HRHGW
MSK 5820-1.5HRHS
MSK 5820-1.5HRHS
MSK 5820-1.5HRHU
MSK 5820-1.5HRHU
MSK 5820-1.5HRHD
MSK 5820-1.5HRHD
See footnotes at end of table.
1 of 4
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 11-04-11
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962F0921604KMA
5962F0921604KMC
5962F0921604KXA
5962F0921604KXC
5962F0921604KYA
5962F0921604KYC
5962F0921604KZA
5962F0921604KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.5KRHGW
MSK 5820-1.5KRHGW
MSK 5820-1.5KRHS
MSK 5820-1.5KRHS
MSK 5820-1.5KRHU
MSK 5820-1.5KRHU
MSK 5820-1.5KRHD
MSK 5820-1.5KRHD
5962F0921605HMA
5962F0921605HMC
5962F0921605HXA
5962F0921605HXC
5962F0921605HYA
5962F0921605HYC
5962F0921605HZA
5962F0921605HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.9HRHGW
MSK 5820-1.9HRHGW
MSK 5820-1.9HRHS
MSK 5820-1.9HRHS
MSK 5820-1.9HRHU
MSK 5820-1.9HRHU
MSK 5820-1.9HRHD
MSK 5820-1.9HRHD
5962F0921605KMA
5962F0921605KMC
5962F0921605KXA
5962F0921605KXC
5962F0921605KYA
5962F0921605KYC
5962F0921605KZA
5962F0921605KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.9KRHGW
MSK 5820-1.9KRHGW
MSK 5820-1.9KRHS
MSK 5820-1.9KRHS
MSK 5820-1.9KRHU
MSK 5820-1.9KRHU
MSK 5820-1.9KRHD
MSK 5820-1.9KRHD
5962F0921606HMA
5962F0921606HMC
5962F0921606HXA
5962F0921606HXC
5962F0921606HYA
5962F0921606HYC
5962F0921606HZA
5962F0921606HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-2.5HRHGW
MSK 5820-2.5HRHGW
MSK 5820-2.5HRHS
MSK 5820-2.5HRHS
MSK 5820-2.5HRHU
MSK 5820-2.5HRHU
MSK 5820-2.5HRHD
MSK 5820-2.5HRHD
5962F0921606KMA
5962F0921606KMC
5962F0921606KXA
5962F0921606KXC
5962F0921606KYA
5962F0921606KYC
5962F0921606KZA
5962F0921606KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-2.5KRHGW
MSK 5820-2.5KRHGW
MSK 5820-2.5KRHS
MSK 5820-2.5KRHS
MSK 5820-2.5KRHU
MSK 5820-2.5KRHU
MSK 5820-2.5KRHD
MSK 5820-2.5KRHD
See footnotes at end of table.
2 of 4
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 11-04-11
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962F0921607HMA
5962F0921607HMC
5962F0921607HXA
5962F0921607HXC
5962F0921607HYA
5962F0921607HYC
5962F0921607HZA
5962F0921607HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-2.8HRHGW
MSK 5820-2.8HRHGW
MSK 5820-2.8HRHS
MSK 5820-2.8HRHS
MSK 5820-2.8HRHU
MSK 5820-2.8HRHU
MSK 5820-2.8HRHD
MSK 5820-2.8HRHD
5962F0921607KMA
5962F0921607KMC
5962F0921607KXA
5962F0921607KXC
5962F0921607KYA
5962F0921607KYC
5962F0921607KZA
5962F0921607KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-2.8KRHGW
MSK 5820-2.8KRHGW
MSK 5820-2.8KRHS
MSK 5820-2.8KRHS
MSK 5820-2.8KRHU
MSK 5820-2.8KRHU
MSK 5820-2.8KRHD
MSK 5820-2.8KRHD
5962F0921608HMA
5962F0921608HMC
5962F0921608HXA
5962F0921608HXC
5962F0921608HYA
5962F0921608HYC
5962F0921608HZA
5962F0921608HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-3.3HRHGW
MSK 5820-3.3HRHGW
MSK 5820-3.3HRHS
MSK 5820-3.3HRHS
MSK 5820-3.3HRHU
MSK 5820-3.3HRHU
MSK 5820-3.3HRHD
MSK 5820-3.3HRHD
5962F0921608KMA
5962F0921608KMC
5962F0921608KXA
5962F0921608KXC
5962F0921608KYA
5962F0921608KYC
5962F0921608KZA
5962F0921608KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-3.3KRHGW
MSK 5820-3.3KRHGW
MSK 5820-3.3KRHS
MSK 5820-3.3KRHS
MSK 5820-3.3KRHU
MSK 5820-3.3KRHU
MSK 5820-3.3KRHD
MSK 5820-3.3KRHD
5962F0921609HMA
5962F0921609HMC
5962F0921609HXA
5962F0921609HXC
5962F0921609HYA
5962F0921609HYC
5962F0921609HZA
5962F0921609HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-5.0HRHGW
MSK 5820-5.0HRHGW
MSK 5820-5.0HRHS
MSK 5820-5.0HRHS
MSK 5820-5.0HRHU
MSK 5820-5.0HRHU
MSK 5820-5.0HRHD
MSK 5820-5.0HRHD
See footnotes at end of table.
3 of 4
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 11-04-11
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962F0921609KMA
5962F0921609KMC
5962F0921609KXA
5962F0921609KXC
5962F0921609KYA
5962F0921609KYC
5962F0921609KZA
5962F0921609KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-5.0KRHGW
MSK 5820-5.0KRHGW
MSK 5820-5.0KRHS
MSK 5820-5.0KRHS
MSK 5820-5.0KRHU
MSK 5820-5.0KRHU
MSK 5820-5.0KRHD
MSK 5820-5.0KRHD
5962F0921610HMA
5962F0921610HMC
5962F0921610HXA
5962F0921610HXC
5962F0921610HYA
5962F0921610HYC
5962F0921610HZA
5962F0921610HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.8HRHGW
MSK 5820-1.8HRHGW
MSK 5820-1.8HRHS
MSK 5820-1.8HRHS
MSK 5820-1.8HRHU
MSK 5820-1.8HRHU
MSK 5820-1.8HRHD
MSK 5820-1.8HRHD
5962F0921610KMA
5962F0921610KMC
5962F0921610KXA
5962F0921610KXC
5962F0921610KYA
5962F0921610KYC
5962F0921610KZA
5962F0921610KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5820-1.8KRHGW
MSK 5820-1.8KRHGW
MSK 5820-1.8KRHS
MSK 5820-1.8KRHS
MSK 5820-1.8KRHU
MSK 5820-1.8KRHU
MSK 5820-1.8KRHD
MSK 5820-1.8KRHD
1/
2/
The lead finish shown for each PIN representing a hermetic
package is the most readily available from the manufacturer
listed for that part. If the desired lead finish is not listed
contact the Vendor to determine its availability.
Caution. Do not use this number for item acquisition. Items
acquired to this number may not satisfy the performance
requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
51651
M. S. Kennedy Corporation
4707 Dey Road
Liverpool, NY 13088
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
4 of 4