Designed and Manufactured in Germany Specification Oscillator type: Rev.: 2 AXIOM145ULN Ultra-Low Noise OCXO in SMD package Parameter Nominal frequency (Note 2) Frequency stability Initial tolerance @ +25°C vs. operating temperature range vs. supply voltage variation (pushing) vs. load change (pulling) Long term (aging) per day st Long term (aging) 1 year Long term (aging) 15 years Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope EFC non-linearity EFC input impedance Modulation bandwidth RF output Signal waveform Load RL Output level Harmonics Spurious Warm-up time @ +25°C Phase noise Short term stability (Allan deviation) Oven alarm output Oscillator enable input (Note 3) Reference voltage VREF output Supply voltage VS Current consumption (steady state) Current consumption (warm-up) Operating temperature range Marking Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. min. typ. max. 10.000 ±0.5 0 ±1.0 VREF/2 Positive Condition MHz ±100 ±5 ±0.5 ±0.5 ±0.5 ±30 ±500 ppb ppb ppb ppb ppb ppb ppb ±1.5 VREF ppm V 10 % kΩ kHz 100 1 Sine wave 50 +5 Unit Date: 2016-01-11 +10 -20 -90 5 Ω dBm dBc dBc min See table 1 -12 5·10 -11 1·10 -11 -10 1·10 1·10 LOW = alarm (not stable) HIGH = ready LOW = Oscillator OFF HIGH = Oscillator ON 5.0 10.5 12.0 12.6 200 340 -20 +75 AXTAL Logo AXIOM145ULN 10.000MHz S/N wwyy 41x30x16 max. 30 Palette VC @ VREF/2 steady state VS ±100 mV RL ±5 % after 10 days operation after 10 days operation after 10 days operation @ -3 dB ±5 % @ 9 ~ 11 MHz ∆ffinal/fnominal < ±100 ppb Option 1 τ=1s τ = 10 s τ = 100 s 0 … 0.4 V 2.4 … 5 V 0 … 0.4 V 2.4 … 12.6 V V V @ +25°C mA °C ww = week, yy = year mm g Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other frequencies on request HCMOS compatible input GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM145ULN Rev.2 Drawing D0 Page 1(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Absolute Maximum Ratings Parameter min. max. Unit Condition Supply Voltage VS Control Voltage VC Oscillator Enable Voltage VOE Storage Temperature Resistance to Soldering Heat -0.5 -0.5 -0.5 -55 VS + 10% 15 VS +125 10 V V V °C sec VS to GND VC to GND VOE to GND @ +245°C Phase Noise – Option 1: Offset A -110 -142 -155 -160 -165 1 Hz 10 Hz 100 Hz 1 kHz ≥10 kHz Table 1 Option B -112 -144 -156 -160 -165 C -115 -146 -157 -160 -165 Unit dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Ordering Code Option 1 Revision Frequency [MHz] [Phase noise] AXIOM145ULN Table 1 Rev.2 10.000 Example: AXIOM145ULN-A_Rev.2 – 10.000 MHz Model Handling and Testing Parameter Handling and Testing Processing Parameter Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS- Compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Procedure Application Note AXAN-011 Application Note AXAN-012 Procedure IEC60749-26 IEC60749-27 Yes Yes AXIOM145ULN Rev.2 Drawing D0 Page 2(4) HBM MM No No Source www.axtal.com www.axtal.com Condition 2000 V 200 V www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing: Pin connections Pin # 1 2 3 4 5 6 7 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM145ULN Rev.2 Drawing D0 Page 3(4) Symbol RF OUT OA GND VREF VC OE VS Function RF Output Oven Alarm Output Ground Reference Voltage Control Voltage (EFC) Oscillator Enable Input Supply Voltage www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] 1 2 D0 D0 10.12.2013 12.12.2013 1 1 2 D0 D1 D0 03.02.2014 16.01.2015 11.01.2016 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks Author Checked First issue preliminary version AXIOM15ULN Changes: operating temp rang, supply voltage. Added: modulation bandwidth New package, new P/N AXIOM145ULN Editorial changes, environmental changes updated Phase noise options added HH HH BN BN HH HH HH BN HH HH AXIOM145ULN Rev.2 Drawing D0 Page 4(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]