Designed and Manufactured in Germany Specification Oscillator type: Rev.: 5 Date: 2014-06-20 AXE1000 UHF Low Phase Noise Crystal Oscillator (SPXO) Parameter min. Frequency range Nominal frequencies Frequency stability Initial tolerance vs. operating temperature range vs. supply voltage variation vs. load change st Long term (aging) 1 year Long term (aging) following years Frequency adjustment range Electronic frequency control (EFC) RF output Signal waveform Load Output level Harmonics Sub-harmonics (multiples of fOUT/10) Spurious Phase noise @ 1000 MHz 300 1300 1000.000 / 1200.000 Start-up time Supply voltage VS Current consumption (steady state) Operating temperature range ±5 ±50 ±1 ±1 ±2 ±1 MHz MHz ppm ppm ppm ppm ppm ppm ppm N.A. Condition @ 25°C (Note 2) VS ±5% RL ±5% @ +25°C @ +25°C, per year on request Sine wave 50 +7 +11 -50 -40 -45 -40 -80 -140 -135 -145 -140 -147 -145 10 20 11.4 12.0 12.6 60 -20 +70 54x40x19 Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. 4. typ. max. Unit 60 Ω dBm dBc dBc dBc dBc/Hz dBc/Hz dBc/Hz ms V mA °C mm g (Note 3) @ 10 kHz @ 100 kHz @ 1 MHz (Note 4) @ +25°C h = 2.0 mm Palette Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other stabilities on request Depending on frequency multiplication factor may be lower or higher than 10 Other supply voltages on request Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Storage Temperature -0.5 -55 VS + 10% +125 Unit Condition V °C VS to GND Ordering Code Model Revision Frequency [MHz] AXE1000 Rev.5 1000.000 Example: AXE1000_Rev.5 – 1000.000 MHz GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXE1000 Rev.5 Drawing D0 Page 1(3) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections Pin# Symbol 1 N.C. 2 GND 3 VS SMA RF OUT Function No Connection Ground Supply Voltage RF Output Handling and Testing Parameter Procedure Handling and Testing Processing Parameter Source Application Note AXAN-011 Application Note AXAN-012 Procedure Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany IEC60749-26 IEC60749-27 Yes Yes AXE1000 Rev.5 Drawing D0 Page 2(3) www.axtal.com www.axtal.com Condition HBM MM 2000 V 200 V No No www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] 4 5 D0 D0 01.10.2012 20.06.2014 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks Frequency range extended to 500 MHz ~ 1200 MHz Frequency range extended to 300 MHz ~ 1300 MHz, environmental conditions updated, editorial changes AXE1000 Rev.5 Drawing D0 Page 3(3) Author Checked BN HH BN HH www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]