P40WG-xxxxE/Z2:1LF Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] PMT-SERIES Rev.05-2011 40 Watt 2:1 Wide Input 2” x 1” Metal Case 1.6 kV DC I/O Isolation Regulated Output Single and Dual Output Continuous Short Circuit Prot. The PMT series P40WG-xxxxE/Z2:1LF is a family of cost effective 40W, single and dual output DC-DC converters with a wide input range of 2:1. These converters are encapsulated in nickel coated brass 2”x1” case with high performance features: 1600VDC input/output isolation voltage, continuous short circuit protection with automatic restart and tight line / load regulation, over current protection, over voltage protection, over temperature protection, high efficiency operation and soft start. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ Start up Time (Nom. Vin and constant resistive load) 2:1 Wide Input (see table) PI Type 20 mA pk-pk 30mS, typ. Output Specifications Voltage Accuracy Voltage Adjustability (only Single Output) Short Circuit Protection Over Load Protection Line Regulation Load Regulation (0% - 100%) Cross Regulation³ Ripple&Noise (20Mhz bandwidth / 1.0uF – pk-pk) Temperature Coefficient Transient Recovery Time4 Transient Response Deviation4 ± 1% ± 10%, max. Indefinite (hiccup, automatic recovery) 115% - 130% of lout, max. ± 0.5%, max. ± 0.5% (single) ±1% (dual balanced load), max. ± 5% (dual) 100 mV (3.3 & 5 Vout) 150 mV (others), max. ± 0.02% / °C 250us, typ. ± 3%, max. General Specifications I/O Isolation Voltage (3 sec.) I/O Isolation Capacitance I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) Safety Standard (designed to meet) 1600 VDC 1000 pF, max. 1000 M Ohm, min. 270 kHz, typ. 95% rel H >328 khrs IEC/EN 60950-1 Physical Specifications Case Material Potting / Base Material Weight Nickel Coated Copper Epoxy / Plastic (UL94V-0 rated) ~ 32g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +71°C (with derating) 105°C -40 to +125°C Free Air Convection (10mm distance required) Soldering 260°C, max. (1.5mm from case 10s.) PMT-Series – P40WG-xxxxE/Z 2:1LF – Single and Dual Output – 2”x1” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Single and Dual Output Order # ) A) ) ) (mA d (m mA ad (mA d a ( a o ) o d ² C) in. L Loa ull L uF) VDC ll L o (VD nt M nt F ) ad ( ge ( t No ent Fu e e e o a n r r % g t r r ( L l e a r r r r lt or Vo Cu Cu cy t Vo t Cu put Cu acit put put put cien Inpu Inpu In Out Out Out Effi Cap SINGLE OUTPUT P40WG-123R3E2:1LF P40WG-1205E2:1LF P40WG-1212E2:1LF P40WG-1215E2:1LF P40WG-243R3E2:1LF P40WG-2405E2:1LF P40WG-2412E2:1LF P40WG-2415E2:1LF P40WG-483R3E2:1LF P40WG-4805E2:1LF P40WG-4812E2:1LF P40WG-4815E2:1LF 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 100 160 40 50 60 90 30 40 40 60 20 20 2444 3663 3663 3663 1208 1811 1831 1811 605 905 915 905 3.3 5 12 15 3.3 5 12 15 3.3 5 12 15 0 0 0 0 0 0 0 0 0 0 0 0 8000 8000 3333 2666 8000 8000 3333 2666 8000 8000 3333 2666 90 91 91 91 91 92 91 92 91 92 91 92 24800 13600 2300 1500 21800 13600 2300 1500 21800 13600 2300 1500 DUAL OUTPUT P40WG-1212Z2:1LF P40WG-1215Z2:1LF P40WG-2412Z2:1LF P40WG-2415Z2:1LF P40WG-4812Z2:1LF P40WG-4815Z2:1LF 9-18 9-18 18-36 18-36 36-72 36-72 50 50 50 40 30 40 3663 3623 1831 1811 906 906 ± 12 ± 15 ± 12 ± 15 ± 12 ± 15 0 0 0 0 0 0 ± 1666 ± 1333 ± 1666 ± 1333 ± 1666 ± 1333 91 92 91 92 92 92 ± 1200 ± 750 ± 1200 ± 750 ± 1200 ± 750 If you need other specifications, please enquire. Notes: PMT-Series – P40WG-xxxxE/Z 2:1LF – Single and Dual Output – 2”x1” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 Package / Pinning / Derating 2.54 (0.10) 10.16 10.16 2.54 (0.40) (0.40) (0.10) 4 5 DIA. 1.00 (0.04) 10.16 (0.40) 6 Bottom View AND OUTPUT MODELS 1 2 3 5.08 5.08 10.16 5.08 (0.20) (0.20) (0.40) (0.20) All dimensions are typical in millimeters (inches). - Pin diameter: 1.0 +/-0.05 (0.04 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) 2" x - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 5.08 (0.20) min. 1" – METAL CASE # 1 2 3 4 5 6 PIN CONNECTIONS SINGLE DUAL +Vin +Vin - Vin - Vin CTRL CTRL +Vout +Vout - Vout COM TRIM - Vout App Notes 1 = Measured Input reflected ripple current with a simulated source inductance of 12uH. 2 = Tested by minimal Vin and constant resistive load. 3 = Dual: One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 4 = Tested by nominal Vin and 25% load step change (75% - 50% - 25% of Io) 5 = The PMT series can meet EN55022 Class A With an external filter in parallel with the input pins. 6 = An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5 7 = The remote on/off control pin is referenced to –Vin (Pin2). PMT-Series – P40WG-xxxxE/Z 2:1LF – Single and Dual Output – 2”x1” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 App Notes EMI Filter: Input filter components are used to help meet conducted emissions requirement. These components should be mounted as close as possible to the module; all leads should be minimized to decrease radiated noise. 12Vin 24Vin 48Vin 12Vin 24Vin 48Vin EMC SPECIFICATIONS Radiated Emissions Conducted 5 Emissions ESD RS 6 EFT 6 Surge CS PFMF EN 55022 CLASS B EN 55022 CLASS B EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Over Voltage Protection (Zender diode clamp) 3.3 Vout: External Output Trimming Output can be externally trimmed. (Single output models only!) Rtrim-up Rtrim-down 6 6 5 4 Under Input Voltage Lockout (typ.) 3.9 V 12 Vin Models Module ON/OFF 8.6V / 7.9V 5 Vout 6.2 V 24 Vin Models Module ON/OFF 17.8V / 16V 12 Vout 15 V 48 Vin Models Module ON/OFF 33.5V / 30.5V 15 Vout 18 V ± 12 Vout ± 15 V ± 15 Vout ± 18 V Remote ON/OFF Control ON: OFF: OFF idle current: 7 3 -12 VDC or open circuit 0 – 1.2 VDC or short circuit PIN2 and PIN3 5mA, typ. CTRL Module ON / OFF Positive logic turns on the module during high logic and off during low logic. Ctrl module on/off can be controlled by an external switch between the ctrl terminal and -Vin terminal. The switch can be an open collector or open drain For positive logic if the ctrl feature is not used, please leave the ctrl pin floating. PMT-Series – P40WG-xxxxE/Z 2:1LF – Single and Dual Output – 2”x1” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4