Modular NETFRAME™ Rack and Accessories Part Numbers: NFR84, NFD484, NFSK, NFDR4X6K, NFCDRK, NFVSM4, NFEDB23, NFSHLF19X18, NFSHLF19X25, NFLRB, NFEP, NFD884, NFD1284, NFREB2, NFBRFK INSTRUCTIONS CM281G © Panduit Corp. 2010 Optional Accessories (1) NETFRAME Extender Door Brackets for 23” Mtg (4) #10-32 Screws NFEDB23 (1) Spool (2)#12-24 Screws NFSK (2) Rear Extender Bracket (8) #12-24 Screws NFREB2 (1) Center (1) Vertical Slack Manager Door, with brackets NFVSM4 NFD884 (8) Bend Radius Fingers NFD1284 NFBRFK (16) Center D-rings NFCDRK NFR84 Modular NETFRAME Rack (2) Vertical Channels (2) Base Angles (1) Pack of (20) 3/8x1.00 Bolt, Lockwasher, Nut (1) Front Top Flange (1) Rear Top Flange (2) Center Waterfalls (1) Pack of (25) #12-24x1/2” Screws (1) Grounding and Hardware Kit (8) D-rings NFDR4X6K (1) End Panel (6)3/8”-16x1.625” Hex Bolts 3/8”-16 Hex Nuts 3/8” Split Lockwashers NFEP (1) Shelf (4) #12-24 Screws NFSHLF19x18 NFSHLF19x25 (shown) 19” Mounting Rear Top Flange Rack Assembly (1) Ladder Rack Bracket (2)3/8”-16x1” Hex Bolts 3/8”-16 Hex Nuts 3/8” Split Lockwasher NFLRB 23” Mounting Front Top Flange Base Angle Vertical Channel Step1 Lay the two vertical channels on the floor or a pair of sturdy saw horses to ease installation. Install (1) Base Angle and Front Top Flange on the vertical channels using (8) 3/8” bolts, lockwashers and nuts provided. Do not tighten. Base Angle Step 2 Roll the rack on its side to install the other base angle and rear top flange using (8) 3/8” bolts, lockwashers and nuts provided. Do not tighten. FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 1 of 4 (1) Door, 4” wide w/ Mtg Brackets (4) #10-32 Screws NFD484 INSTRUCTIONS CM281G Location Guide: 19” Rack Center Waterfall Step 3 Stand the rack upright.Verify #12-24 tapped holes are EIA spaced at 18.31”, square the rack and tighten bolts. Install the two waterfalls with the #10-32 screws provided. Mount rack to floor using the location guide below for mounting hole and overall size information. 23.875 17.00 6.00 11.00 28.40 Shelf Installation NFSHLF19X18, NFHSLF19X25 Grounding Kit (1) Barrel Lug (1) 1/4”-20 Screw Barrel Lug and Grounding Screw mounts to rear of rack in one of four optional places. C Channel #10-32 Screws Rear Extender Bracket Installation NFREB2 Use (2) #12-24 screws to secure each bracket in desired location Flush Mount Shelf Plate Rear Bracket 6 in. Mount Front Bracket (2) #12-24 SCREWS End Panel NFEP NFEP attaches to rack with (6) 3/8”16x.625” Hex Bolts, 3/8”-16 Hex Nuts and 3/8” Split Lockwashers provided. Attach Rear Bracket to rear of rack at desired height with #12-24 screws. Attach Front Bracket to front of rack at desired height with #12-24 screws. Attach Shelf Plate to Front and Rear Brackets with the #10-32 screws. The Shelf Plate “C” Channel mates with the bracket “J’ Slot to provide adjustable mounting. Can be mounted “flush” or extended 6 inches. . Ladder Rack Bracket Installation NFLRB NFEP NFLRB Top Plate attaches to Main Bracket with (2) 3/8”16x1” hex bolts, 3/8”-16 hex nuts and 3/8” splitlockwashers provided NFLRB Top Plate can be assembled perpendicular to Main Bracket to support parallel runs of ladder rack. NFLRB assembles to NFR84 using 3/8”-16x1” hex bolt, nut, and lockwasher provided with NFR84 FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 2 of 4 J Slot INSTRUCTIONS CM281G D-Rings Installation: NFDR4X6K Center D-Rings Installation: NFCDRK Side Mount EIA/NETFRAME Racks Vertical Slack Manager attaches to your frame with (3) 3/ 8” bolts, nuts and lock washers. Right side installation snaps down Left side installation snaps up NFCDRK NFDR4x6K NETFRAME Vertical Slack Manager: NFVSM4 Spool Installation Angled Flange Step 1 Step 2 Align buttons with mounting leg slot Push buttons through backbone until mounting face is flush with backbone. Step 3 Apply downward pressure until plastic spool clicks into place. Removal/Replacement Step 4 Pull back on angled flange while applying upward pressure Step 5 Repeat steps 1-3 Bend Radius Fingers Installation NFBRFK Fingers install by snapping (down right side) (up left side) use (3) #12-24 screws to secure each finger section in desired location. Note: Start finger installation from bottom of rack and continue upwards on the right side. Start finger installation from top of rack and continue down on the left side. FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 3 of 4 INSTRUCTIONS CM281G Door Installation NFD484 NFEDB23 NFD484 installed to NETFRAME with (4) #10x32 screws provided. Spool NFSK NFSK attaches to rack with (2) #12-24 screws provided NFEDB23 installed to NETFRAME Top Flange with #10-32 screws provided. To be used when rack is set-up for 23” mounting Top Center Door NFD884 NFD1284 1. Use 3/8”-16x1” bolt, 3/8”-16 nut and 3/8” lockwasher provided with NETFRAME to gang two racks together using NETFRAME junction holes located on side of rack channels. 2. Straddling the two racks, fasten Top Bracket and Bottom Bracket with #10-32x5/16” screws provided. 3. Door installs to top and bottom brackets by aligning lower hinge pin to hinge pin mounting hole. Squeeze knobs together, then align upper hinge pin to upper hinge pin mounting hole. Release pressure on knobs to set door in place. NFD884 Bottom Bracket For instuctions in Local Languages and Technical Support: www.panduit.com/resources/install_maitain.asp www.panduit.com Page 4 of 4 E-mail: [email protected] Fax (708)444-6448