Download

5W AC-DC Power-Supply PAC5D
●
●
●
●
●
●
Enclosed plastic case
85 … 264 VAC universal input range
Continuously short circuit protected
Isolation class II
MTBF > 300000 h
3 years product warranty
Model guide
Type
PAC5D03S
PAC5D05S
PAC5D09S
PAC5D12S
PAC5D15S
PAC5D24S
Output
voltage
[VDC]
[%]
3.3
±3
5.0
±2
9.0
±2
12
±2
15
±2
24
±2
Output power
[W]
4.2
5
5
5
5
5.5
Output
current
[mA] max
1250
1000
550
420
333
230
Ripple & noise
BW 20 MHz
[mVp-p] max.
120
120
100
100
100
100
Efficiency typ.
@ full load
[%]
74
78
78
80
82
83
Capacitive
load
[µF] max.
4000
4000
1000
820
820
330
Stand by power
consumption
[W]
0.3
0.3
0.3
0.3
0.3
0.3
Specifications
Input
Voltage range
Line frequency range
Full load input current
Inrush current
Recommended fuse
Isolation
Input to output isolation
voltage
Isolation resistance
Leakage current
Output
Line regulation
Load regulation@10 to 100%
load change
Temperature coefficient
Ripple&noise @ BW 20 MHz
Minimum load
Protection
Short circuit
Over current
Over voltage
Over temperature
General
Hold up time @ full load
Reliability MTBF
MIL-HDBK-217@25°C
Switching frequency
Physical
Dimensions
Weight
Case material
Soldering temperature
EMI
85..264 VAC or
100..370 VDC
Power derating see diagram
47…63 Hz
150 mA @ 115 VAC,
70 mA @ 230 VAC
10 A typ. @ 115 VAC
20 A typ. @ 230 VAC
1 A slow blow
CE
RE
ESD
RS
EFT
4000 VAC, tested for 1 min.
EMS
8
10 Ω
0.1 mA max. @ 230 VAC
±0.5 %, typ.
±1 %, typ.
Surge
CS
± 0.02 % / °C
60 mV max.
1 % of full load
PFM
Continuous, auto recovery
>110 % of full load
Over voltage shut down
150 °C, max.
12 ms @ 115 VAC. typ.
80 ms @ 230 VAC. typ.
>300000 h
140 kHz, max.
25.4 x 50.8 x 15.2 mm
31 g
UL94V-0 rated
260°C, 10s, 1.5mm from case
Voltage dips,
short and
interruptions
immunity
Safety approvals
Safety
Environmental
Operating temperature
(ambient)
Operating case temperature
Power derating 55°C to 70°C
Power derating -25°C to 0°C
Storage temperature
Storage humidity
Cooling
EN55022 (CISPR22), class B
EN55022 (CISPR22), class B
IEC, EN61000-4-2
contakt ± 6 kV, air ±8 kV,
perf. criteria B
IEC, EN61000-4-3, 10 V / m
perf. criteria A
IEC, EN61000-4-4, ±2 kV,
perf. criteria B
with input filter PIF001A,
IEC, EN61000-4-4, ±4 kV,
perf. criteria B
IEC, EN61000-4-5, ±1 kV / ±2 kV
perf. criteria B
IEC, EN61000-4-5, ±2 kV / ±4 kV
With input filter PIF001A,
perf. criteria B
IEC, EN61000-4-6, 10 Vrms
perf. criteria A
IEC, EN61000-4-8, 10 A / m
perf. criteria A
IEC, EN61000-4-11, 0…70 %
perf. criteria B
EN60950, UL60950
Class II
-25 °C to +70 °C
(with derating, see diagram)
95 °C, max.
2 % per °C, See diagram
1.25 % per °C, See diagram
-40 °C to +105 °C
95 %, non-condensing
Free air convection
Note:
1. Ripple and noise are measured by parallel wire method. See figure “Noise measure method”.
o
2. Unless otherwise specified, all specifications above are measured at rated input voltage,rated output load, Ta 25 C and
humidity < 75 %.
Page 1 of 4
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5W AC-DC Power-Supply PAC5D
Noise measure method
Measure points for oscilloscope
Fuse
L
PAC5DxxS
C1
1 µF
C2
10 µF
Load
+Vo
N
-Vo
25.4
12.7
12.7
Unit in mm
Typical application circuit
Figure 1
L
F1
NTC
PAC5DxxS
C1
+Vout
~
N
U
MOV
Typ
C2
=
-Vout
PAC5D03S
PAC5D05S
PAC5D09S
PAC5D12S
PAC5D15S
PAC5D24S
C1
[µF]
1
1
1
1
1
1
C2
[µF]
220
220
100
100
100
47
PE
Page 2 of 4
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5W AC-DC Power-Supply PAC5D
Circuit for extended ripple and noise reduction
Figure 2
-ϑ
Input Filter PIF001B
L F1
PAC5DxxS Module
L
~
U
=
N
N
PE
Recommended layout
Part
Fuse
Metal oxide varistor, MOV
X capacitor
Y capacitors
Single coil
Common mode coil
NTC Thermistor
Designation, Value
1 A, 250 VAC, “Time delay” type
S14K350
0.1 µF, 275 VAC
1 nF, 400 VAC
4.7 µH, 2 A
2.2 mH, 1 A
12D-5
Note:
1. Output filtering capacitor C1 is a electrolytic capacitor. It is recommended to use high frequency
and low impedance electrolytic capacitor. For capacitance and current of capacitor please refer to
manufacture’s datasheet. Voltage derating of capacitor should be 80 % or above.
2. C2 is a ceramic capacitor, it is used to filter the high frequency noise.
3. The varistor MOV protect the AC/DC-converter at input voltage transients.
4. The NTC thermistor is used for the inrush current limitation.
Page 3 of 4
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5W AC-DC Power-Supply PAC5D
Dimensions
Pin connections
Pin
1
2
3
4
AC In (L)
AC In (N)
+ DC Out
- DC Out
PHI-CON is a trademark of HY-LINE Holding GmbH.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for
use carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the
express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose
failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected
to result in significant injury to the user. Rev: 10.15 f
Page 4 of 4
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]