Download

6W DC-DC Converter P6M-Series
●
●
●
●
●
●
●
Wide 2:1 input range
Flat case profile 7 mm
Continuous short circuit protection
Over Voltage protection
Soft start function
No internal tantalum capacitors
Efficiency up to 88 %
Model selection guide
Type
Input
voltage
range
[VDC]
Single output
P6M053R3S 4.5…9
P6M0505S
4.5…9
P6M0512S
4.5…9
P6M0515S
4.5…9
P6M123R3S 9...18
P6M1205S
9...18
P6M1212S
9...18
P6M1215S
9...18
P6M243R3S 18...36
P6M2405S
18...36
P6M2412S
18...36
P6M2415S
18...36
P6M483R3S 36...75
P6M4805S
36...75
P6M4812S
36...75
P6M4815S
36...75
Dual output
P6M0512D
4.5…9
P6M0515D
4.5…9
P6M1212D
9...18
P6M1215D
9...18
P6M2412D
18...36
P6M2415D
18...36
P6M4812D
36...75
P6M4815D
36...75
Input current
no
full
load
load
[mA]
[mA]
Output
voltage
45
45
45
45
25
25
25
25
25
25
25
25
25
25
25
25
905
1315
1520
1520
360
620
590
590
225
310
300
290
110
155
150
145
3.3
5.0
12.0
15.0
3.3
5.0
12.0
15.0
3.3
5.0
12.0
15.0
3.3
5.0
12.0
15.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1000
1000
500
400
1000
1200
500
400
1200
1200
500
400
1200
1200
500
400
73
76
79
79
76
81
85
85
73
80
84
86
74
80
84
85
1000
1000
680
680
1000
1200
680
470
1200
1200
680
470
1200
1200
680
470
50
50
15
15
10
10
6
6
1500
1500
580
580
290
290
145
145
±12.0
±15.0
±12.0
±15.0
±12.0
±15.0
±12.0
±15.0
0
0
0
0
0
0
0
0
±250
±200
±250
±200
±250
±200
±250
±200
82
82
88
88
88
88
87
88
2 x 220
2 x 220
2 x 220
2 x 220
2 x 220
2 x 220
2 x 220
2 x 220
[VDC]
Output current
min.
[mA]
max.
[mA]
Efficiency Capacitance
typ.
load max.
(see note 3)
[%]
[µF]
Page 1 of 2
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
6W DC-DC Converter P6M-Series
Page 2 of 3
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
6W DC-DC Converter P6M-Series
Specifications
Input
Filter
Pi network
Start up time @ min. Vin and 20 ms, max.
constant resistive load
Reflected ripple current
20 mAp-p (see note 5)
Output
Voltage accuracy
±1%
Voltage balance (dual outputs)
±1%
Ripple and noise (at 20 MHz BW)
75 mVp-p, max. (see note 2)
Short circuit protection
Continuous
Short circuit restart
Automatic
Overcurrent protection
185 % typ, of full load
Line regulation
± 0.5 %, max.
Load regulation (@ 0...100 % load) ± 1 %, max. @ balanced load
Cross regulation (dual output) ± 5 %, max. (see note 1)
Temperature coefficient
± 0.02 % / °C
Transient response deviation ± 3 %, max. (see note 4)
Over voltage protection
3.3 V output type
3.9 V, z-diode clamp voltage
5 V output type
6.2 V, z-diode clamp voltage
12 V output type
15 V, z-diode clamp voltage
15 V output type
18 V, z-diode clamp voltage
± 12 V output type
± 15 V, z-diode clamp voltage
± 15 V output type
± 18 V, z-diode clamp voltage
Physical
Dimensions
44.5 x 28 x 7 mm
Weight
25 g, max.
Isolation
Rated voltage input to output,
input or output to case
Resistance
Capacitance input / output
General
Safety standard (designet to
meet)
Reliability calculated MTBF
(Mil –HDBK-217 F)
Switching frequency
Environmental
Operating temperatur
(ambient)
Case temperature
Storage temperature
Derating
Humidity
Cooling
Absolute maximum ratings
5 V input types
12 V input types
24 V input types
48 V input types
Soldering temperature
1.5 mm distance from case
500 VAC
6
50 Ω min. @ 500 V
1 nF, max.
IEC / EN60950-1
> 1.28 Mio. hours
330 kHz
-40 °C to +85 °C
100 °C max.
-40 °C to +125 °C
None required
Up to 95%, non condensing
Free-air convection
Input voltage, 100 ms, max.
-0.7…15 VDC
-0.7…36 VDC
-0.7…50 VDC
-0.7…100 VDC
260 °C, 10 s max.
Note:
1. One load is 25 % to 100 % load, the other load is 100 % load, the output voltage variable rate is within ±5 %.
2. Typical value at nominal input voltage and full load,measured by 20 MHz oscilloscope.
3. Test by nominal input voltage and constant resistive load.
4. Tested by normal Vin and 50 % load step change ( 100 % … 50 % of full output current, 50 % … 0 % of full output current ).
5. Measured Input reflected ripple current with a simulated source inductance of 12 µH.
6. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating.
Dimensions
Pin connections
Pin
1
2
3
4
5
Single
-V Input
+V Input
+V Output
Omitted
-V Output
Dual
-V Input
+V Input
+V Output
Common
-V Output
Notes :
All dimensions are typical in millimeters.
1. Pin diameter: 1.0 ±0.05
2. Pin pitch tolerance: ±0.35
3. Case Tolerance: ±0.5
4. The converter metal case is in contact with the cleaning stand of on the PCB.
To keep isolation, an adequate PCB layout on the mounted side is required.
PHI-CON is a trademark of HY-LINE power components.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions
carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without
the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and
whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably
expected to result in significant injury to the user. Rev: 01.14 f
Page 3 of 3
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]