Data Sheet

Freescale Semiconductor
Addendum
Document Number: QFN_Addendum
Rev. 0, 07/2014
Addendum for New QFN
Package Migration
This addendum provides the changes to the 98A case outline numbers for products covered in this book.
Case outlines were changed because of the migration from gold wire to copper wire in some packages. See
the table below for the old (gold wire) package versus the new (copper wire) package.
To view the new drawing, go to Freescale.com and search on the new 98A package number for your
device.
For more information about QFN package use, see EB806: Electrical Connection Recommendations for
the Exposed Pad on QFN and DFN Packages.
© Freescale Semiconductor, Inc., 2014. All rights reserved.
Part Number
MC68HC908JW32
Package Description
Original (gold wire)
Current (copper wire)
package document number package document number
48 QFN
98ARH99048A
98ASA00466D
MC9RS08LA8
48 QFN
98ARL10606D
98ASA00466D
MC9S08GT16A
32 QFN
98ARH99035A
98ASA00473D
MC9S908QE32
32 QFN
98ARE10566D
98ASA00473D
MC9S908QE8
32 QFN
98ASA00071D
98ASA00736D
MC9S08JS16
24 QFN
98ARL10608D
98ASA00734D
MC9S08QG8
24 QFN
98ARL10605D
98ASA00474D
MC9S08SH8
24 QFN
98ARE10714D
98ASA00474D
MC9RS08KB12
24 QFN
98ASA00087D
98ASA00602D
MC9S08QG8
16 QFN
98ARE10614D
98ASA00671D
MC9RS08KB12
8 DFN
98ARL10557D
98ASA00672D
6 DFN
98ARL10602D
98ASA00735D
MC9S08AC16
MC9S908AC60
MC9S08AC128
MC9S08AW60
MC9S08GB60A
MC9S08GT16A
MC9S08JM16
MC9S08JM60
MC9S08LL16
MC9S08QE128
MC9S08QE32
MC9S08RG60
MCF51CN128
MC9S08QB8
MC9S08QG8
MC9RS08KA2
Addendum for New QFN Package Migration, Rev. 0
2
Freescale Semiconductor
Freescale Semiconductor
Data Sheet: Technical Data
Document Number: MC9S08JS16
Rev. 4, 4/2009
MC9S08JS16
MC9S08JS16 Series
Covers:
MC9S08JS16
MC9S08JS8
MC9S08JS16L
MC9S08JS8L
Features:
• 8-Bit HCS08 Central Processor Unit (CPU)
– 48 MHz HCS08 CPU (central processor unit)
– 24 MHz internal bus frequency
– Support for up to 32 interrupt/reset sources
• Memory Options
– Up to 16 KB of on-chip in-circuit programmable flash
memory with block protection and security options
– Up to 512 bytes of on-chip RAM
– 256 bytes of USB RAM
• Clock Source Options
– Clock source options include crystal, resonator, external
clock
– MCG (multi-purpose clock generator) — PLL and FLL;
internal reference clock with trim adjustment
• System Protection
– Optional computer operating properly (COP) reset with
option to run from independent 1 kHz internal clock
source or the bus clock
– Low-voltage detection
– Illegal opcode detection with reset
– Illegal address detection with reset
• Power-Saving Modes
– Wait plus two stops
• USB Bootload
– Mass erase entire flash array
– Partial erase flash array — erase all flash blocks except
for the first 1 KB of flash
– Program flash
• Peripherals
– USB — USB 2.0 full-speed (12 Mbps) with dedicated
on-chip 3.3 V regulator and transceiver; supports
endpoint 0 and up to 6 additional endpoints
TBD
20 W-SOIC
Case 751D
– SPI — One 8- or 16-bit selectable serial peripheral
interface module with a receive data buffer hardware
match function
– SCI — One serial communications interface module
with optional 13 bit break. Full duplex non-return to zero
(NRZ); LIN master extended break generation; LIN
slave extended break detection; wakeup on active edge
– MTIM — One 8-bit modulo counter with 8-bit prescaler
and overflow interrupt
– TPM — One 2-channel 16-bit timer/pulse-width
modulator (TPM) module; selectable input capture,
output compare, and edge-aligned PWM capability on
each channel; timer module may be configured for
buffered, centered PWM (CPWM) on all channels
– KBI — 8-pin keyboard interrupt module
– RTC — Real-time counter with binary- or
decimal-based prescaler
– CRC — Hardware CRC generator circuit using 16-bit
shift register; CRC16-CCITT compliancy with
x16+x12+x5+1 polynomial
• Input/Output
– Software selectable pullups on ports when used as inputs
– Software selectable slew rate control on ports when used
as outputs
– Software selectable drive strength on ports when used as
outputs
– Master reset pin and power-on reset (POR)
– Internal pullup on RESET, IRQ, and BKGD/MS pins to
reduce customer system cost
• Package Options
– 24-pin quad flat no-lead (QFN)
– 20-pin small outline IC package (SOIC)
This document contains information on a product under development. Freescale reserves the
right to change or discontinue this product without notice.
© Freescale Semiconductor, Inc., 2008-2009. All rights reserved.
24 QFN
Case 1982-01
Table of Contents
1
2
3
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3.1 Parameter Classification . . . . . . . . . . . . . . . . . . . . . . . . .6
3.2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . .6
3.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .7
3.4 Electrostatic Discharge (ESD) Protection Characteristics8
3.5 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.6 Supply Current Characteristics . . . . . . . . . . . . . . . . . . .15
3.7 External Oscillator (XOSC) Characteristics . . . . . . . . .17
3.8 MCG Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.9
4
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.1 Control Timing . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.2 Timer/PWM (TPM) Module Timing. . . . . . . . . .
3.10 SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11 Flash Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12 USB Electricals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Mechanical Drawings. . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
21
24
25
26
26
26
Revision History
To provide the most up-to-date information, the revision of our documents on the World Wide Web will
be the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://freescale.com/
The following revision history table summarizes changes contained in this document.
Revision
Date
Description of Changes
1
9/1/2008
Initial public released
2
1/8/2009
In Table 7, changed the parameter description of RIDD and S3IDD, the typicals of
RIDD were changed as well.
3
3/9/2009
Corrected the 24-pin QFN case number and doc. number information.
4
4/24/2009
Added new parts information about MC9S08JS16L and MC9S08JS8L.
Related Documentation
Find the most current versions of all documents at: http://www.freescale.com
Reference Manual
(MC9S08JS16RM)
Contains extensive product information including modes of operation, memory,
resets and interrupts, register definition, port pins, CPU, and all module
information.
MC9S08JS16 Series MCU Data Sheet, Rev. 4
2
Freescale Semiconductor
MCU Block Diagram
1
MCU Block Diagram
The block diagram, Figure 1, shows the structure of the MC9S08JS16 series MCU.
ON-CHIP ICE AND
DEBUG MODULE (DBG)
HCS08 CORE
RESET
IRQ
USB
MODULE
FULL SPEED
USB
USB ENDPOINT TRANSCEIVER
RAM
CPU
BDC
PTA1/KBIP1/MISO
HCS08 SYSTEM CONTROL
8-BIT KEYBOARD
INTERRUPT MODULE (KBI)
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
IRQ
KBIPx 8
PTA2/KBIP2/MOSI
MISO
8-/16-BIT
COP
PTA0/KBIP0/TPMCH0
LVD
SERIAL PERIPHERAL
INTERFACE MODULE (SPI)
USER FLASH (IN BYTES)
MC9S08JS16 = 16,384
MC9S08JS16L = 16,384
MC9S08JS8 = 8,192
MC9S08JS8L = 8,192
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI)
PORT A
BKGD/MS
USBDP
USBDN
MOSI
SPSCK
SS
PTA3/KBIP3/SPSCK
PTA4/KBIP4/SS
PTA5/KBIP5/TPMCH1
RxD
PTA6/KBIP6/RxD
TxD
PTA7/KBIP7/TxD
TPMCH0
USER RAM (IN BYTES)
512
2-CHANNEL TIMER/PWM
TPMCH1
MODULE (TPM)
Bootloader ROM (IN BYTES)
4096
EXTAL
MULTI-PURPOSE CLOCK
GENERATOR (MCG)
VDD
VSS
VUSB33
XTAL
PORT B
PTB3/BLMS
8-BIT MODULO TIMER
MODULE (MTIM)
VSSOSC
PTB0/IRQ/TCLK
PTB1/RESET
PTB2/BKGD/MS
TCLK
PTB4/XTAL
PTB5/EXTAL
LOW-POWER OSCILLATOR
16-BIT Cyclic Redundancy
Check Generator
MODULE (CRC)
SYSTEM
VOLTAGE
REGULATOR
USB 3.3 V VOLTAGE REGULATOR
REAL-TIME COUNTER
(RTC)
NOTES:
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled (IRQPE = 1). Pulldown is enabled if
rising edge detect is selected (IRQEDG = 1).
3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD.
4. RESET contains integrated pullup device if PTB1 enabled as reset pin function (RSTPE = 1).
5. Pin contains integrated pullup device.
6. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can
be used to reconfigure the pullup as a pulldown device.
Figure 1. MC9S08JS16 Series Block Diagram
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
3
Pin Assignments
2
Pin Assignments
This section shows the pin assignments in the packages available for the MC9S08JS16 series.
Table 1. Pin Availability by Package Pin-Count
Pin Number
(Package)
<-- Lowest
Priority
--> Highest
24 (QFN) 20 (SOIC)
Port Pin
Alt 1
Alt 2
1
4
PTB0
2
5
PTB1
3
6
PTB2
4
7
PTB3
5
8
PTA0
6
—
NC
7
9
8
IRQ
TCLK
RESET
BKGD
MS
BLMS
KBIP0
TPMCH0
PTA1
KBIP1
MISO
10
PTA2
KBIP2
MOSI
9
11
PTA3
KBIP3
SPSCK
10
12
PTA4
KBIP4
SS
11
13
12
—
13
14
VSS
14
15
USBDN
15
16
USBDP
16
17
VUSB33
17
18
PTA5
18
—
NC
19
19
20
VDD
NC
KBIP5
TPMCH1
PTA6
KBIP6
RxD
20
PTA7
KBIP7
TxD
21
1
PTB4
XTAL
22
2
PTB5
EXTAL
23
3
24
—
VSSOSC
NC
MC9S08JS16 Series MCU Data Sheet, Rev. 4
4
Freescale Semiconductor
PTB4/XTAL
PTA7/KBIP7/TxD
PTA6/KBIP6/RxD
24 23
PTB5/EXTAL
VSSOSC
NC
Pin Assignments
22
21
20
19
18 NC
PTB0/IRQ/TCLK 1
17 PTA5/KBIP5/TPMCH1
PTB1/RESET 2
16 VUSB33
PTB2/BKGD/MS 3
24-Pin QFN
PTB3/BLMS 4
15 USBDP
PTA0/KBIP0/TPMCH0 5
14 USBDN
9
10
11
PTA3/KBIP3/SPSCK
PTA4/KBIP4/SS
VDD
12
NC
8
PTA2/KBIP2/MOSI
13 VSS
7
PTA1/KBIP1/MISO
NC 6
Figure 2. MC9S08JS16 Series in 24-QFN Package
PTB4/XTAL
1
20
PTA7/KBIP7/TxD
PTB5/EXTAL
2
19
PTA6/KBIP6/RxD
VSSOSC
3
18
PTA5/KBIP5/TPMCH1
PTB0/IRQ/TCLK
4
17
VUSB33
PTB1/RESET
5
16
USBDP
PTB2/BKGD/MS
6
15
USBDN
PTB3/BLMS
7
14
VSS
PTA0/KBIP0/TPMCH0
8
13
VDD
PTA1/KBIP1/MISO
9
12
PTA4/KBIP4/SS
PTA2/KBIP2/MOSI
10
11
PTA3/KBIP3/SPSCK
Figure 3. MC9S08JS16 Series in 20-pin SOIC Package
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
5
Electrical Characteristics
3
Electrical Characteristics
This chapter contains electrical and timing specifications.
3.1
Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the
customer a better understanding, the following classification is used and the parameters are tagged
accordingly in the tables where appropriate:
Table 2. Parameter Classifications
P
Those parameters are guaranteed during production testing on each individual device.
C
Those parameters are achieved by the design characterization by measuring a
statistically relevant sample size across process variations.
T
Those parameters are achieved by design characterization on a small sample size from
typical devices under typical conditions unless otherwise noted. All values shown in the
typical column are within this category.
D
Those parameters are derived mainly from simulations.
NOTE
The above classifications are used in the column labeled “C” in applicable
tables of this data sheet.
3.2
Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not
guaranteed. Stress beyond the limits specified in Table 3 may affect device reliability or cause permanent
damage to the device. For functional operating conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (for instance, either VSS or VDD).
Table 3. Absolute Maximum Ratings
Rating
Supply voltage
Input voltage
Instantaneous maximum current
(applies to all port pins)1, 2, 3
Maximum current into VDD
Storage temperature
Maximum junction temperature
Single pin limit
Symbol
Value
Unit
VDD
2.7 to 5.5
V
VIn
–0.3 to VDD + 0.3
V
ID
±25
mA
IDD
120
mA
Tstg
–55 to 150
°C
TJ
150
°C
MC9S08JS16 Series MCU Data Sheet, Rev. 4
6
Freescale Semiconductor
Electrical Characteristics
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2
All functional non-supply pins are internally clamped to VSS and VDD.
3
Power supply must maintain regulation within operating VDD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low which would reduce overall power
consumption.
3.3
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take
PI/O into account in power calculations, determine the difference between actual pin voltage and VSS or
VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy
loads), the difference between pin voltage and VSS or VDD will be very small.
Table 4. Thermal Characteristics
Rating
Operating temperature range (packaged)
Symbol
Value
Unit
TA
TL to TH
-40 to 85
°C
θJA
92
33
°C/W
Thermal resistance 1,2,3,4
24-pin QFN
1s
2s2p
20-pin SOIC
1s
2s2p
86
58
1
Junction temperature is a function of die size, on-chip power dissipation, package thermal
resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation
of other components on the board, and board thermal resistance
2 Junction to Ambient Natural Convection
3 1s — Single layer board, one signal layer
4
2s2p — Four layer board, 2 signal and 2 power layers
The average chip-junction temperature (TJ) in °C can be obtained from:
TJ = TA + (PD × θJA)
Eqn. 1
where:
TA = Ambient temperature, °C
θJA = Package thermal resistance, junction-to-ambient, °C/W
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
7
Electrical Characteristics
PD = Pint + PI/OPint = IDD × VDD, Watts — chip internal power
PI/O = Power dissipation on input and output pins — user determined
For most applications, PI/O << Pint and can be neglected. An approximate relationship between PD and TJ
(if PI/O is neglected) is:
PD = K ÷ (TJ + 273°C)
Eqn. 2
Solving Equation 1 and Equation 2 for K gives:
K = PD × (TA + 273°C) + θJA × (PD)2
Eqn. 3
where K is a constant pertaining to the particular part. K can be determined from Equation 3 by measuring
PD (at equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by
solving Equation 1 and Equation 2 iteratively for any value of TA.
3.4
Electrostatic Discharge (ESD) Protection Characteristics
Although damage from static discharge is much less common on these devices than on early CMOS
circuits, normal handling precautions must be used to avoid exposure to static discharge. Qualification
tests are performed to ensure that these devices can withstand exposure to reasonable levels of static
without suffering any permanent damage. This device was qualified to AEC-Q100 Rev E. A device is
considered to have failed if, after exposure to ESD pulses, the device no longer meets the device
specification requirements. Complete DC parametric and functional testing is performed per the applicable
device specification at room temperature followed by hot temperature, unless specified otherwise in the
device specification.
Table 5. ESD Protection Characteristics
Parameter
Symbol
Value
Unit
ESD Target for Machine Model (MM) — MM circuit
description
VTHMM
200
V
ESD Target for Human Body Model (HBM) — HBM
circuit description
VTHHBM
2000
V
3.5
DC Characteristics
This section includes information about power supply requirements, I/O pin characteristics, and power
supply current in various operating modes.
Table 6. DC Characteristics
Num C
1
Parameter
Operating voltage2
Symbol
Min
Typical1
Max
Unit
—
2.7
—
5.5
V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
8
Freescale Semiconductor
Electrical Characteristics
Table 6. DC Characteristics (continued)
Num C
2
3
P
P
Parameter
Symbol
Output high voltage — Low drive (PTxDSn = 0)
5 V, ILoad = –2 mA
3 V, ILoad = –0.6 mA
5 V, ILoad = –0.4 mA
3 V, ILoad = –0.24 mA
Output high voltage — High drive (PTxDSn = 1)
5 V, ILoad = –10 mA
3 V, ILoad = –3 mA
5 V, ILoad = –2 mA
3 V, ILoad = –0.4 mA
Output low voltage — Low drive (PTxDSn = 0)
5 V, ILoad = 2 mA
3 V, ILoad = 0.6 mA
5 V, ILoad = 0.4 mA
3 V, ILoad = 0.24 mA
Output low voltage — High drive (PTxDSn = 1)
5 V, ILoad = 10 mA
3 V, ILoad = 3 mA
5 V, ILoad = 2 mA
3 V, ILoad = 0.4 mA
VOH
VOL
Min
Typical1
Max
VDD – 1.5
VDD – 1.5
VDD – 0.8
VDD – 0.8
—
—
—
—
—
—
—
—
VDD – 1.5
VDD – 1.5
VDD – 0.8
VDD – 0.8
—
—
—
—
—
—
—
—
1.5
1.5
0.8
0.8
—
—
—
—
—
—
—
—
1.5
1.5
0.8
0.8
—
—
—
—
—
—
—
—
Unit
V
V
Output high current — Max total IOH for all ports
4
P
5
P
5V
3V
IOHT
—
—
—
—
100
60
mA
5V
3V
IOLT
—
—
—
—
100
60
mA
Output low current — Max total IOL for all ports
6
P Input high voltage; all digital inputs
VIH
0.65 × VDD
—
—
7
P Input low voltage; all digital inputs
VIL
—
—
0.35 × VDD
8
P Input hysteresis; all digital inputs
Vhys
0.06 × VDD
—
—
mV
|IIn|
—
0.1
1
μA
9
P Input leakage current; input only pins
3
V
10
P High Impedance (off-state) leakage current
|IOZ|
—
0.1
1
μA
11
P Internal pullup resistors4
RPU
20
45
65
kΩ
12
P Internal pulldown resistors5
RPD
20
45
65
kΩ
13
C
RPUPD
900
1425
1575
3090
kΩ
14
C Input capacitance; all non-supply pins
CIn
—
—
8
pF
15
C RAM retention voltage
VRAM
0.6
1.0
—
V
16
P POR rearm voltage
VPOR
0.9
1.4
2.0
V
17
D POR rearm time
tPOR
10
—
—
μs
3
Internal pullup resistor to USBDP (to VUSB33)
Idle
Transmit
—
—
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
9
Electrical Characteristics
Table 6. DC Characteristics (continued)
Num C
18
19
20
21
22
P
P
C
P
P
23
C
24
T
Parameter
Symbol
Low-voltage detection threshold —
high range
VDD falling
VDD rising
Low-voltage detection threshold —
low range
VDD falling
VDD rising
Low-voltage warning threshold —
high range 1
VDD falling
VDD rising
Low-voltage warning threshold —
high range 0
VDD falling
VDD rising
Low-voltage warning threshold
low range 1
VDD falling
VDD rising
Low-voltage warning threshold —
low range 0
VDD falling
VDD rising
VLVD1
VLVD0
VLVW3
VLVW2
VLVW1
VLVW0
Min
Typical1
Max
3.9
4.0
4.0
4.1
4.1
4.2
2.48
2.54
2.56
2.62
2.64
2.70
4.5
4.6
4.6
4.7
4.7
4.8
4.2
4.3
4.3
4.4
4.4
4.5
2.84
2.90
2.92
2.98
3.00
3.06
2.66
2.72
2.74
2.80
2.82
2.88
—
—
100
60
—
—
Unit
V
V
V
V
V
V
Low-voltage inhibit reset/recover hysteresis
5V
3V
Vhys
mV
Typical values are based on characterization data at 25 °C unless otherwise stated.
Operating voltage with USB enabled can be found in Section 3.11, “USB Electricals.”
3 Measured with V = V
In
DD or VSS.
4 Measured with V = V .
In
SS
5 Measured with V = V .
In
DD
1
2
MC9S08JS16 Series MCU Data Sheet, Rev. 4
10
Freescale Semiconductor
Electrical Characteristics
IOH vs VDD-VOH (Low Drive) at VDD = 3 V
0.30
VDD-VOH (V)
0.25
0.20
0.15
-40C
25C
0.10
85C
0.05
0.00
0
-0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 -2.2 -2.4 -2.6 -2.8 -3
IOH (mA)
Figure 4. Typical IOH (Low Drive) vs VDD–VOH at VDD = 3 V
VDD-VOH (V)
IOH vs VDD-VOH (High Drive) at VDD = 3 V
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
-40C
25C
85C
0.00
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10 -11 -12 -13 -14 -15
IOH (mA)
Figure 5. Typical IOH (High Drive) vs VDD–VOH at VDD = 3 V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
11
Electrical Characteristics
IOH vs VDD-VOH (Low Drive) at VDD = 5 V
0.7
0.6
VOL (V)
0.5
-40C
25C
0.4
0.3
85C
0.2
0.1
0.0
0
-0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 -2.2 -2.4 -2.6 -2.8 -3
IOH(mA)
Figure 6. Typical IOH (Low Drive) vs VDD–VOH at VDD = 5 V
VDD-VOH (V)
IOH vs VDD-VOH (High Drive) at VDD = 5 V
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
-40C
25C
85C
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10 -11 -12 -13 -14 -15
IOH (mA)
Figure 7. Typical IOH (High Drive) vs VDD–VOH at VDD = 5 V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
12
Freescale Semiconductor
Electrical Characteristics
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0.00
-3
-2
.2
-2
.4
-2
.6
-2
.8
-2
-1
-1
.2
-1
.4
-1
.6
-1
.8
-40C
25C
85C
0
-0
.2
-0
.4
-0
.6
-0
.8
VOL (V)
IOL vs VOL (Low Drive) at VDD = 5 V
IOL(mA)
Figure 8. IOL vs VOL (Low Drive) at VDD = 5 V
IOL vs VOL (High Drive) at VDD = 5 V
0.25
VOL (V)
0.20
-40C
25C
85C
0.15
0.10
0.05
0.00
0
-1
-2
-3
-4
-5
-6
-7
-8
-9 -10 -11 -12 -13 -14 -15
IOL (mA)
Figure 9. IOL vs VOL (High Drive) at VDD = 5 V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
13
Electrical Characteristics
IOL vs VOL (Low Drive) at VDD = 3 V
1.0
VOL (V)
0.8
-40C
25C
85C
0.6
0.4
0.2
0.0
0 -0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 -2.2 -2.4 -2.6 -2.8 -3
IOL (mA)
Figure 10. IOL vs VOL (Low Drive) at VDD = 3 V
IOL vs VOL (High Drive) at VDD = 3 V
1.4
1.2
VOL (V)
1.0
-40C
25C
85C
0.8
0.6
0.4
0.2
0.0
0
-1
-2
-3
-4
-5
-6
-7
-8
-9 -10 -11 -12 -13 -14 -15
IOL (mA)
Figure 11. IOL vs VOL (High Drive) at VDD = 3 V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
14
Freescale Semiconductor
Electrical Characteristics
3.6
Supply Current Characteristics
Table 7. Supply Current Characteristics
3
4
5
6
Max2
5
1.03
—
3
0.83
—
5
19.93
—
3
18.74
—
5
1.36
—
μA
3
1.18
—
μA
5
1.50
—
μA
3
1.31
—
μA
5
300
—
nA
3
300
—
nA
5
106.7
—
μA
3
95.6
—
μA
5
5.6
—
μA
3
5.3
—
μA
ΔIUSBE
5
1.5
—
mA
ISUSP
5
273.3
—
μA
Parameter
Symbol
1
C
Run supply current3 measured at (CPU clock
= 2 MHz, fBus = 1 MHz, BLPE mode)
RIDD
2
P
Run supply current3 measured at (CPU
clock = 48 MHz, fBus = 24 MHz, PEE mode, all
module on)
RIDD
3
P
4
P
Stop3 mode supply current, all module off
S3IDD
5
P
RTC adder to stop2 or stop33, 25 °C
ΔISRTC
6
P
LVD adder to stop3 (LVDE = LVDSE = 1)
ΔISLVD
7
P
Adder to stop3 for oscillator enabled4
(ERCLKEN =1 and EREFSTEN = 1)
ΔISOSC
9
2
Typical1
C
8
1
VDD (V)
Num
T
T
Stop2 mode supply current
USB module enable
USB suspend
current5
current6
S2IDD
Unit
mA
mA
Typicals are measured at 25 °C. See Figure 12 through Figure 10 for typical curves across voltage/temperature.
Values given here are preliminary estimates prior to completing characterization.
Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait
mode. Wait mode typical is 560 μA at 5 V and 422 μA at 3 V with fBus = 1 MHz.
Values given under the following conditions: low range operation (RANGE = 0), low power mode (HGO = 0).
Here USB module is enabled and clocked at 48 MHz (USBEN = 1, USBVREN =1, USBPHYEN = 1 and USBPU = 1), and
D+ and D– pulled down by two 15.1 kΩ resisters independently. The current consumption may be much higher when the
packets are being transmitted through the attached cable.
MCU enters stop3 mode, USB bus in idle state. The USB suspend current will be dominated by the D+ pullup resister.
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
15
Electrical Characteristics
Typical Run IDD for PEE,FBE & BLPE
IDD vs. VDD
25.000
IDD(mA)
20.000
15.000
PEE,48MHz Core
FBE,8MHz Core
BLPE,2MHz Core
10.000
5.000
0.000
2.5
3
3.5
4
4.5
5
5.5
VDD(V)
Figure 12. Typical Run IDD for PEE, FBE and BLPE Modes (IDD vs. VDD)
MC9S08JS16 Series MCU Data Sheet, Rev. 4
16
Freescale Semiconductor
Electrical Characteristics
3.7
External Oscillator (XOSC) Characteristics
Table 8. Oscillator Electrical Specifications (Temperature Range = –40 to 85°C Ambient)
Num
C
Rating
Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1)
Low range (RANGE = 0)
High range (RANGE = 1) FEE or FBE mode2
High range (RANGE = 1) PEE or PBE mode3
High range (RANGE = 1, HGO = 1) BLPE mode
High range (RANGE = 1, HGO = 0) BLPE mode
1
C
2
— Load capacitors
3
—
4
Series resistor
Low range, low gain (RANGE = 0, HGO = 0)
Low range, high gain (RANGE = 0, HGO = 1)
High range, low gain (RANGE = 1, HGO = 0)
—
High range, high gain (RANGE = 1, HGO = 1)
≥ 8 MHz
4 MHz
1 MHz
5
6
T
T
Symbol
Min
Typ1
Max
Unit
flo
fhi-fll
fhi-pll
fhi-hgo
fhi-lp
32
1
1
1
1
—
—
—
—
—
38.4
5
16
16
8
kHz
MHz
MHz
MHz
MHz
C1, C2
Feedback resistor
Low range (32 kHz to 38.4 kHz)
High range (1 MHz to 16 MHz)
RF
RS
Crystal start-up time4
Low range, low gain (RANGE = 0, HGO = 0)
Low range, high gain (RANGE = 0, HGO = 1)
High range, low gain (RANGE = 1, HGO = 0)5
High range, high gain (RANGE = 1, HGO = 1)5
t
t
CSTL-LP
CSTL-HGO
t
CSTH-LP
t
CSTH-HGO
Square wave input clock frequency (EREFS = 0, ERCLKEN = 1)
FEE or FBE mode2
PEE or PBE mode3
BLPE mode
fextal
See crystal or resonator
manufacturer’s recommendation.
—
—
10
1
—
—
—
—
—
0
100
0
—
—
—
—
—
—
0
0
0
0
10
20
—
—
—
—
200
400
5
15
—
—
—
—
ms
0.03125
1
0
—
—
—
5
16
40
MHz
MΩ
kΩ
Typical data was characterized at 3.0 V, 25 °C or is recommended value.
When MCG is configured for FEE or FBE mode, input clock source must be divided using RDIV to within the range of 31.25 kHz
to 39.0625 kHz.
3 When MCG is configured for PEE or PBE mode, input clock source must be divided using RDIV to within the range of 1 MHz to
2 MHz.
4 This parameter is characterized and not tested on each device. Proper PC board layout procedures must be followed to achieve
specifications.
5 4 MHz crystal.
1
2
MCU
EXTAL
XTAL
RF
C1
Crystal or Resonator
RS
C2
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
17
Electrical Characteristics
3.8
MCG Specifications
Table 9. MCG Frequency Specifications (Temperature Range = –40 to 85°C Ambient)
Num C
Rating
Symbol
Min
Typical
Max
Unit
fint_ut
25
32.7
41.66
kHz
1
C Average internal reference frequency — untrimmed
2
P Average internal reference frequency — trimmed
fint_t
31.25
—
39.0625
kHz
T Internal reference startup time
tirefst
—
60
100
μs
C DCO output frequency range — untrimmed
fdco_ut
25.6
33.48
42.66
MHz
5
P DCO output frequency range — trimmed
fdco_t
32
—
40
MHz
6
Resolution of trimmed DCO output frequency at
C
fixed voltage and temperature (using FTRIM)
Δfdco_res_t
—
±0.1
±0.2
%fdco
7
C
Resolution of trimmed DCO output frequency at
fixed voltage and temperature (not using FTRIM)
Δfdco_res_t
—
±0.2
±0.4
%fdco
8
P
Total deviation of trimmed DCO output frequency
over voltage and temperature
Δfdco_t
—
0.5
–1.0
±2
%fdco
9
Total deviation of trimmed DCO output frequency
C over fixed voltage and temperature range of
0–70 °C
Δfdco_t
—
±0.5
±1
%fdco
10
C FLL acquisition time1
tfll_acquire
—
—
1
ms
11
D PLL acquisition
time2
tpll_acquire
—
—
1
ms
12
Long term Jitter of DCO output clock (averaged over
C
2ms interval)3
CJitter
—
0.02
0.2
%fdco
13
D VCO operating frequency
fvco
7.0
—
55.0
MHz
14
D PLL reference frequency range
fpll_ref
1.0
—
2.0
MHz
15
T
fpll_jitter_2ms
—
0.5904
—
%
16
T Jitter of PLL output clock measured over 625 ns5
fpll_jitter_625ns
—
0.5664
—
%
Dlock
±1.49
—
±2.98
%
Dunl
±4.47
—
±5.97
%
3
4
17
Long term accuracy of PLL output clock (averaged
over 2 ms)
D Lock entry frequency
tolerance6
tolerance7
18
D Lock exit frequency
19
D Lock time — FLL
tfll_lock
—
—
20
D Lock time — PLL
tpll_lock
—
—
21
D
Loss of external clock minimum frequency —
RANGE = 0
floc_low
(3/5) x fint
—
—
kHz
22
D
Loss of external clock minimum frequency —
RANGE = 1
floc_high
(16/5) x fint
—
—
kHz
tfll_acquire+
1075(1/fint_t)
tpll_acquire+
1075(1/fpll_ref)
s
s
1
This specification applies any time the FLL reference source or reference divider is changed, trim value changed or changing
from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference,
this specification assumes it is already running.
2
This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled
(BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it
is already running.
MC9S08JS16 Series MCU Data Sheet, Rev. 4
18
Freescale Semiconductor
Electrical Characteristics
3
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBUS.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for
a given interval.
4
Jitter measurements are based upon a 48 MHz clock frequency.
5
625 ns represents 5 time quanta for CAN applications, under worst case conditions of 8 MHz CAN bus clock, 1 Mbps CAN
bus speed, and 8 time quanta per bit for bit time settings. 5 time quanta is the minimum time between a synchronization edge
and the sample point of a bit using 8 time quanta per bit.
6
Below Dlock minimum, the MCG is guaranteed to enter lock. Above Dlock maximum, the MCG will not enter lock. But if the MCG
is already in lock, then the MCG may stay in lock.
7
Below Dunl minimum, the MCG will not exit lock if already in lock. Above Dunl maximum, the MCG is guaranteed to exit lock.
3.9
AC Characteristics
This section describes AC timing characteristics for each peripheral system.
3.9.1
Control Timing
Figure 13. Control Timing
Num
C
1
D
2
D
Symbol
Min
Typical1
Max
Unit
Bus frequency (tcyc = 1/fBus)
fBus
DC
—
24
MHz
Internal low-power oscillator period
tLPO
700
—
1300
μs
textrst
1.5 × tSelf_reset
—
—
ns
Parameter
width2
3
D
External reset pulse
(tcyc = 1/fSelf_reset)
4
D
Reset low drive
trstdrv
66 × tcyc
—
—
ns
5
D
Active background debug mode latch setup
time
tMSSU
25
—
—
ns
6
D
Active background debug mode latch hold
time
tMSH
25
—
—
ns
7
D
IRQ pulse width
Asynchronous path2
Synchronous path3
tILIH, tIHIL
100
1.5 × tcyc
—
—
ns
8
D
KBIPx pulse width
Asynchronous path2
Synchronous path3
tILIH, tIHIL
100
1.5 × tcyc
—
—
ns
C
Port rise and fall time (load = 50 pF)4
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
tRise, tFall
—
—
3
30
—
—
ns
9
Typical values are based on characterization data at VDD = 5.0 V, 25 °C unless otherwise stated.
This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to
override reset requests from internal sources.
3
This is the minimum pulse width guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not
be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case.
4
Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range –40°C to 85°C.
1
2
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
19
Electrical Characteristics
textrst
RESET PIN
Figure 14. Reset Timing
tIHIL
IRQ/KBIPx
IRQ/KBIPx
tILIH
Figure 15. IRQ/KBIPx Timing
3.9.2
Timer/PWM (TPM) Module Timing
Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that
can be used as the optional external source to the timer counter. These synchronizers operate from the
current bus rate clock.
Table 10. TPM Input Timing
Num
C
1
D
2
Function
Symbol
Min
Max
Unit
External clock frequency
fTPMext
dc
fBus/4
MHz
D
External clock period
tTPMext
4
—
tcyc
3
D
External clock high time
tclkh
1.5
—
tcyc
4
D
External clock low time
tclkl
1.5
—
tcyc
5
D
Input capture pulse width
tICPW
1.5
—
tcyc
tTPMext
tclkh
TPMxCLK
tclkl
Figure 16. Timer External Clock
MC9S08JS16 Series MCU Data Sheet, Rev. 4
20
Freescale Semiconductor
Electrical Characteristics
tICPW
TPMxCHn
TPMxCHn
tICPW
Figure 17. Timer Input Capture Pulse
3.10
SPI Characteristics
Table 11 and Figure 18 through Figure 21 describe the timing requirements for the SPI system.
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
21
Electrical Characteristics
Table 11. SPI Electrical Characteristic
Num1
Characteristic2
C
Symbol
Min
Typical
Max
Unit
Master
Slave
fop
fop
fBus/2048DC
—
—
fBus/2
fBus/4
Hz
Master
Slave
tSCK
tSCK
2
4
—
—
2048
—
tcyc
Master
Slave
tLead
tLead
—
—
1/2
1/2
—
—
tSCK
Master
Slave
tLag
tLag
—
—
1/2
1/2
—
—
tSCK
Master
Slave
tSCKH
—
1/2 tSCK – 25
1/2 tSCK
1/2 tSCK
—
—
ns
Master
Slave
tSCKL
—
1/2 tSCK – 25
1/2 tSCK
1/2 tSCK
—
—
ns
Master
Slave
tSI(M)
tSI(S)
30
30
—
—
—
—
ns
Master
Slave
tHI(M)
tHI(S)
30
30
—
—
—
—
ns
Operating frequency3
1
D
2
D
3
D
4
D
5
D
6
D
7
D
8
D
9
D
Access time, slave4
tA
—
—
40
ns
10
D
Disable time, slave5
tdis
—
—
40
ns
11
D
Master
Slave
tSO
tSO
—
—
—
—
25
25
ns
12
D
Master
Slave
tHO
tHO
–10
–10
—
—
—
—
ns
Cycle time
Enable lead time
Enable lag time
Clock (SPSCK) high time
Clock (SPSCK) low time
Data setup time (inputs)
Data hold time (inputs)
Data setup time (outputs)
Data hold time (outputs)
1
Refer to Figure 18 through Figure 21.
All timing is shown with respect to 20% VDD and 80% VDD, unless noted; 50 pF load on all SPI pins. All timing assumes slew
rate control disabled and high drive strength enabled for SPI output pins.
3 The maximum frequency is 8 MHz when input filter on SPI pins is disabled.
4 Time to data active from high-impedance state.
5 Hold time to high-impedance state.
2
MC9S08JS16 Series MCU Data Sheet, Rev. 4
22
Freescale Semiconductor
Electrical Characteristics
SS1
(OUTPUT)
3
1
2
SCK
(CPOL = 0)
(OUTPUT)
5
4
SCK
(CPOL = 1)
(OUTPUT)
5
4
6
MISO
(INPUT)
7
MSB IN2
BIT 6 . . . 1
10
MOSI
(OUTPUT)
LSB IN
12
10
MSB OUT2
BIT 6 . . . 1
LSB OUT
NOTES:
1. SS output mode (MODFEN = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 18. SPI Master Timing (CPHA = 0)
SS(1)
(OUTPUT)
1
3
2
SCK
(CPOL = 0)
(OUTPUT)
5
4
SCK
(CPOL = 1)
(OUTPUT)
5
4
6
MISO
(INPUT)
7
MSB IN(2)
LSB IN
12
10
MOSI
(OUTPUT)
BIT 6 . . . 1
MSB OUT(2)
BIT 6 . . . 1
LSB OUT
NOTES:
1. SS output mode (MODFEN = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 19. SPI Master Timing (CPHA = 1)
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
23
Electrical Characteristics
SS
(INPUT)
3
1
SCK
(CPOL = 0)
(INPUT)
5
4
2
SCK
(CPOL = 1)
(INPUT)
5
4
8
MISO
(OUTPUT)
12
10
BIT 6 . . . 1
MSB OUT
SLAVE
SEE
NOTE
SLAVE LSB OUT
7
6
MOSI
(INPUT)
9
BIT 6 . . . 1
MSB IN
LSB IN
NOTE:
1. Not defined but normally MSB of character just received
Figure 20. SPI Slave Timing (CPHA = 0)
SS
(INPUT)
3
1
2
SCK
(CPOL = 0)
(INPUT)
5
4
SCK
(CPOL = 1)
(INPUT)
5
4
10
MISO
(OUTPUT)
SEE
NOTE
8
MOSI
(INPUT)
SLAVE
12
MSB OUT
6
BIT 6 . . . 1
9
SLAVE LSB OUT
7
MSB IN
BIT 6 . . . 1
LSB IN
NOTE:
1. Not defined but normally LSB of character just received
Figure 21. SPI Slave Timing (CPHA = 1)
3.11
Flash Specifications
This section provides details about program/erase times and program-erase endurance for the flash
memory. Program and erase operations do not require any special power sources other than the normal
VDD supply.
MC9S08JS16 Series MCU Data Sheet, Rev. 4
24
Freescale Semiconductor
Electrical Characteristics
Table 12. Flash Characteristics
Symbol
Min
Typical1
Max
Unit
Supply voltage for program/erase
Vprog/erase
2.7
—
5.5
V
D
Supply voltage for read operation
VRead
2.7
—
5.5
V
3
D
Internal FCLK frequency2
fFCLK
150
—
200
kHz
4
D
Internal FCLK period (1/FCLK)
tFcyc
5
—
6.67
μs
5
P
Byte program time (random location)2
tprog
9
tFcyc
6
P
Byte program time (burst mode)2
tBurst
4
tFcyc
7
P
Page erase time3
tPage
4000
tFcyc
8
P
Mass erase time2
tMass
20,000
tFcyc
9
C
Program/erase endurance4
TL to TH = –40°C to 85 °C
T = 25 °C
10
C
Data retention5
Num
C
1
D
2
Characteristic
—
10,000
—
—
100,000
—
—
cycles
tD_ret
15
100
—
years
Typical values are based on characterization data at VDD = 5.0 V, 25 °C unless otherwise stated.
The frequency of this clock is controlled by a software setting.
3 These values are hardware state machine controlled. User code does not need to count cycles. This information
supplied for calculating approximate time to program and erase.
4 Typical endurance for flash was evaluated for this product family on the 9S12Dx64. For additional information on
how Freescale Semiconductor defines typical endurance, please refer to Engineering Bulletin EB619/D, Typical
Endurance for Nonvolatile Memory.
5
Typical data retention values are based on intrinsic capability of the technology measured at high temperature and
de-rated to 25 °C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines
typical data retention, please refer to Engineering Bulletin EB618/D, Typical Data Retention for Nonvolatile Memory.
1
2
3.12
USB Electricals
The USB electricals for the S08USBV1 module conform to the standards documented by the Universal
Serial Bus Implementers Forum. For the most up-to-date standards, visit http://www.usb.org.
If the Freescale S08USBV1 implementation requires additional or deviant electrical characteristics, this
space would be used to communicate that information.
Table 13. Internal USB 3.3 V Voltage Regulator Characteristics
Symbol
Min
Typical
Max
Unit
Regulator operating voltage
Vregin
3.9
—
5.5
V
Vreg output
Vregout
3
3.3
3.6
V
Vreg filter capacitor
Cusbreg
—
100
—
pF
Vusb33 input with internal Vreg disabled
Vusb33in
3
3.3
3.6
V
MC9S08JS16 Series MCU Data Sheet, Rev. 4
Freescale Semiconductor
25
Ordering Information
Table 14. External 3.3 V Voltage Regulator Supply for Vusb33 Pin
External 3.3 V regulator output current
4
Symbol
Min
Typical
Max
Unit
—
39
—
—
mA
Ordering Information
This section contains ordering information for Device Numbering System. See below for an example of
the device numbering system.
MC 9 S08 JS
16 (L) C XX
Status
(MC = Fully qualified)
Memory
(9 = Flash-based)
Core
Package designator (See Table 15)
Temperature range
(C = –40 °C to 85 °C)
USB bootloader
supported at 3.3 V
Family
4.1
Approximate memory size (in KB)
Package Information
Table 15. Package Descriptions
Pin Count
4.2
Package Type
Abbreviation
Designator
Case No.
Document No.
24
Quad Flat No-Leads
QFN
FK
1982-01
98ARL10608D
20
Wide Body Small Outline
Integrated Circuit
W-SOIC
WJ
751D
98ASB42343B
Mechanical Drawings
This following pages contain mechanical specifications for MC9S08JS16 series package options.
• 24-pin QFN (quad flat no-lead)
• 20-pin W-SOIC (wide body small outline integrated circuit)
MC9S08JS16 Series MCU Data Sheet, Rev. 4
26
Freescale Semiconductor
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or +1-303-675-2140
Fax: +1-303-675-2150
[email protected]
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of
Freescale Semiconductor, Inc. All other product or service names
are the property of their respective owners.
© Freescale Semiconductor, Inc. 2008-2009. All rights reserved.
MC9S08JS16
Rev. 4
4/2009