Product Specification Dimensions PX series – Brilliant image quality ▪▪ Up to 12 megapixel and 25 fps ▪▪ Quad-tap CCD sensors ▪▪ Very high dynamic range ▪▪ Simplified integration with USB 3 Vision Size 12 x M3 depth 5 Sensor Camera Type Bottom View Full Frames Resolution [max. fps] Monochrome PXU-60M.Q 1" 2752 x 2200 25 PXU-120M.Q 1" 4248 x 2832 13 Side View Front View Back View q 45 46,9 q 26 5,7 ±0,025 temperature measurement point Notice ø 30 Latest software version and technical documentation available at: 9,8 26 4 - M3 depth 5 You can operate the camera to USB 2.0 port. However, the frame rate will be less than on a USB 3.0 port. Quick Start Guide PXU cameras (USB3 Vision™) 9 17,6 C-Mount 4 6,75 18 12,4 www.baumer.com/vision/login Safety System Requirements Installation Lens mount Safety Precautions Notice See the User's Guide for the complete safety instructions! CPU Single-camera system Multi-camera system Recommended Recommended Intel(R) Core(TM) i5-2520M Intel(R) Core(TM) i7-3770 CPU CPU @ 2.50GHz, Cores: 4 @ 3.40GHz, Cores: 8 4 GB 8 GB RAM CE We declare, under our sole responsibility, that the previously described Baumer PXU cameras conform with the directives of the CE. RoHS All PXU cameras comply with the recommendation of the European Union concerning RoHS Rules. ▪▪ Protect the sensor from dirt and moisture. ▪▪ Do not allow the camera to become contaminated with foreign objects. Operating Microsoft Windows 7 32 / 64 bit systems (required for USB 3.0) system (OS) Microsoft® Windows® 8 32 / 64 bit systems (required for USB 3.0) ® Environmental Requirements -10°C ... +70°C Storage temp. Operating temp. see Heat Transmission Humidity 10 % ... 90 % Non-condensing Further Information For further information about our products, please visit www.baumer.com For technical issues, please contact our technical support: [email protected] · Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86 © Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany Technical data has been fully checked, but accuracy of printed matter is not guaranteed. Subject to change without notice. Printed in Germany 06/15. v1.2 11140291 Notice Further technical details are available on the respective data sheets. ® Notice Ensure the sensor and lens are not contaminated with dust and airborne particles when mounting the support or the lens to the device! The following points are very important: ▪▪ Install the camera in an environment that is as dust free as possible! ▪▪ Keep the dust cover (bag) on the camera for as long as possible! ▪▪ Hold the printer with the sensor downwards if the sensor is uncovered. ▪▪ Avoid contact with any of the camera‘s optical surfaces! General Description LED signals 1 Heat Transmission 2 Caution Heat can damage the camera. Heat must be dissipated adequately to ensure that the temperatures do not exceed the values in the table below. LED As there numerous options for installation, Baumer does not specify a specific method for proper heat dissipation. As there are numerous possibilities for installation, Baumer do not specifiy a specific method for proper heat dissipation, but suggest the following principles: 3 ▪▪ operate the cameras only in mounted condition ▪▪ mounting in combination with forced convection may provide proper heat dissipation 4 No. Description No. 1 Lens mount (C-Mount) 2 LED 3 4 Description Signal Meaning USB 3.0 port green flash Power on green USB 3.0 connection red USB 2.0 connection yellow Data transfer red flash Update LED Power supply / Digial IO Notice Measurement Point The USB 3.0 port is only used for data transfer. The power is supplied via the Power / Digital IO port. Maximum Temperature T You can operate the camera to USB 2.0 port. However, the frame rate will be less than on a USB 3.0 port. Installation Data Interface / Digital IOs T 70°C (122°F) Troubleshooting USB 3.0 Micro B 1 23 45 1 2 3 4 5 6 7 8 9 10 6 7 8 9 10 VBUS DD+ ID GND MicB_SSTXMicB_SSTX+ GND_DRAIN MicB_SSRXMicB_SSRX+ Power / Digital IOs (M8 / 8 pins / wire colors of the connecting cable) 6 5 4 7 1 2 3 4 OUT 3 Power VCC+ IN 1 IO GND white brown green yellow 8 2 5 6 7 8 IO Power VCC OUT 1 Power GND OUT 2 grey pink blue red Power Supply Power VCC 12 V DC ... 24 V DC ± 20% I 210 mA ... 420 mA Power consumption approx. 5 W (25 fps) 1. Check camera operation using the LED signals. open wire ▪▪ Connect the camera to the USB connection on your PC using an appropriate cable. → If LED is red: • Camera is connected to USB 2.0. ▪▪ Connect the camera to power supply → If LED is green: • Check if camera is being used by another application. • Otherwise reconnect camera / restart software. ▪▪ If required, connect a trigger and / or flash to the digital IOs. 3 1 Installing the camera: Installation example 1 - PCI USB board 2 - USB cable 3 - Cable for trigger, flash and power 2. Check connection using Windows Device Manager: → If device is not listed: • Check the host controller power supply. • Check USB 3.0 cable and connection. → If device is regularly not listed • Check USB 3.0 driver installation.