REVISIONS LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 PMIC N/A PREPARED BY RICK OFFICER Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA 13-07-11 4 A REV 5 6 7 8 9 10 11 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil/ TITLE MICROCIRCUIT, LINEAR, SINGLE DIFFERENTIAL COMPARATOR, MONOLITHIC SILICON APPROVED BY CHARLES F. SAFFLE SIZE AMSC N/A 3 CODE IDENT. NO. DWG NO. V62/13611 16236 PAGE 1 OF 11 5962-V049-13 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance single differential comparator microcircuit, with an operating temperature range of -55°C to +125°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/13611 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 Circuit function TL331 Single differential comparator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins X 5 JEDEC PUB 95 Package style MO-178-AA Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z DLA LAND AND MARITIME COLUMBUS, OHIO Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 2 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) ................................................................................................. 36 V 2/ Differential input voltage (VID) .................................................................................... ±36 V 3/ Input voltage range (either input) ............................................................................... -0.3 V to 36 V Output voltage (VOUT) ............................................................................................... 36 V Output current (IOUT) ................................................................................................. 20 mA Duration of output short circuit to ground ................................................................... Unlimited 4/ Operating virtual junction temperature range (TJ) ...................................................... 150°C Storage temperature range (TSTG) ............................................................................ -65°C to +150°C Thermal resistance, junction to case (θJC) ................................................................. 65.4°C/W Thermal resistance, junction to ambient (θJA) ............................................................ 299°C/W 1.4 Recommended operating conditions. 5/ Supply voltage range (VCC) ....................................................................................... 5 V Operating free-air temperature range (TA) ................................................................. -55°C to +125°C 1/ 2/ 3/ 4/ 5/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential voltages, are with respect to the network ground. Differential voltages are at +IN with respect to –IN. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 3 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Schematic diagram. The schematic diagram shall be as shown in figure 4. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Input offset voltage Symbol VIO Conditions 2/ VCC = 5 V unless otherwise specified Temperature, TA IIO Limits Min 25°C VCC = 5 V to 30 V, VO = 1.4 V, 25°C VO = 1.4 V 01 5 IIB 25°C VO = 1.4 V 01 50 25°C VICR 01 -250 AVD 01 High level output current IOH Low level output voltage 0 to VCC – 1.5 V 0 to VCC -2 25°C 01 VOH = 5 V, VID = 1 V 25°C 01 VOH = 30 V, VID = 1 V -55°C to +125°C IOL = 4 mA, VID = -1 V 25°C VCC = 15 V, VO = 1.4 V to 11.4 V, 50 V/ mV RL ≥ 15 kΩ to VCC VOL nA -400 -55°C to +125°C Large signal differential voltage amplification nA 250 -55°C to +125°C Common mode 3/ input voltage range mV 9 -55°C to +125°C Input bias current Unit Max -55°C to +125°C VIC = VIC(min) Input offset current Device type 01 50 nA 1 µA 400 mV 700 -55°C to +125°C Low level output current IOL VOL = 1.5 V, VID = -1 V 25°C 01 Supply current ICC RL = ∞, VCC = 5 V 25°C 01 6 mA 0.7 mA See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 5 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions 2/ VCC = 5 V unless otherwise specified Temperature, TA Device type Limits Min Unit Max Switching characteristics. Response time 100 mV input step with 5 mV overdrive, RL connected to 5 V 25°C 01 µs 1.3 typical through 5.1 kΩ, CL = 15 pF 4/ 5/ TTL level input step, RL connected to 5 V through 5.1 kΩ, 0.3 typical CL = 15 pF 4/ 5/ 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, all characteristics are measured with zero common mode input voltage. 3/ The voltage at either input or common mode should not be allowed to go negative by more than 0.3 V. The upper end of the common mode voltage range is +VCC – 1.5 V, but either or both inputs can go to 30 V without damage. 4/ CL includes probe and jig capacitance. 5/ The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 6 Case X FIGURE 1. Case outline. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 7 Case X – continued. Dimensions Symbol Inch Millimeters Min Max Min Max A --- .057 --- 1.45 A1 .000 .006 0.00 0.15 b .011 .019 0.30 0.50 c .003 .008 0.08 0.22 D .108 .120 2.75 3.05 E .057 .068 1.45 1.75 E1 .102 .118 2.60 3.00 e L .037 BSC .011 0.95 BSC .022 0.30 0.55 L1 .009 BSC 0.25 BSC n 5 leads 5 leads NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 mm (0.006 inch) per side. 3. Falls with JEDEC MO-178-AA. FIGURE 1. Case outline - Continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 8 Device type 01 Case outline X Terminal number Terminal symbol 1 -IN 2 -VCC / GND 3 +IN 4 OUT 5 +VCC FIGURE 2. Terminal connections. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 9 FIGURE 3. Logic diagram. FIGURE 4. Schematic diagram. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ 2/ Device manufacturer CAGE code Transportation mode and quantity 3/ Top side marking 4/ Vendor part number V62/13611-01XE 01295 Reel of 250 TEPU TL331MDBVTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the package option addendum at the end of the manufacturer’s data sheet. 3/ Package drawings, thermal data, and symbolization are available from the manufacturer. 4/ The actual top side marking has one additional character that designates the wafer fab/assembly site. CAGE code 01295 DLA LAND AND MARITIME COLUMBUS, OHIO Source of supply Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13611 PAGE 11