V6208601 VID

REVISIONS
LTR
DESCRIPTION
A
Add footnote 4/ under paragraph 1.5.
Add a JEDEC reference to section 2.
Update document paragraphs to current
requirements. - ro
DATE
APPROVED
15-04-02
C. SAFFLE
CURRENT DESIGN ACTIVITY CAGE CODE 16236
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.24
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
A
A
A
A
A
A
A
A
A
A
A
PAGE
1
2
3
4
5
6
7
8
9
10
11
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
08-03-11
TITLE
MICROCIRCUIT, DIGITAL-LINEAR, SINGLE
CHANNEL HIGH SPEED MOSFET DRIVER,
MONOLITHIC SILICON
APPROVED BY
ROBERT M. HEBER
SIZE
A
REV
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
CODE IDENT. NO.
DWG NO.
V62/08601
16236
A
PAGE
1
OF
11
5962-V038-15
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance single channel high speed MOSFET driver
microcircuit, with an operating temperature range of -55C to +125C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/08601
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
TPS2816
02
TPS2817
03
04
05
TPS2818
TPS2819
TPS2828
06
TPS2829
Circuit function
Single channel high speed MOSFET inverting driver with
active pullup input
Single channel high speed MOSFET noninverting driver with
active pullup input
Single channel high speed MOSFET inverting driver
Single channel high speed MOSFET noninverting driver
Single channel high speed MOSFET inverting driver,
no regulator
Single channel high speed MOSFET noninverting driver,
no regulator
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
5
JEDEC PUB 95
Package style
MO-178-AA
Plastic surface mount
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture:
Finish designator
A
B
C
D
E
Z
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage range (VCC) ....................................................................................... -0.3 V to 15 V 2/
Regulator supply voltage range (VDD) ....................................................................... VCC – 0.3 V to 42 V 2/
Input voltage range (VIN) ........................................................................................... -0.3 V to VCC + 0.5 V 2/
Output pin voltage range ............................................................................................ -0.5 V to VCC + 0.5 V 2/
Continuous regulator output current (ICC) .................................................................. 25 mA
Continuous output current (IOUT) ............................................................................... 100 mA
Continuous total power dissipation (PD) ..................................................................... See 1.5, dissipation rating table
Junction temperature range (TJ) ................................................................................
Storage temperature range (TSTG) ..............................................................................
Lead temperature 1.6 mm (1/16 inch) form case for 10 seconds ...............................
Thermal resistance, junction to ambient (JC) ............................................................
+150C
-65C to +150C
260C
55C/W
Thermal resistance, junction to ambient (JA) ............................................................ 255.4C/W
1.4 Recommended operating conditions. 3/
Supply voltage range (VCC) ....................................................................................... 4 V to 14 V
Regulator input voltage range (VDD) :
Device types 01, 02, 03, 04 .................................................................................... 8 V to 40 V
Input voltage range (VIN) ........................................................................................... -0.3 V to VCC
Continuous regulator output current range (ICC) ........................................................ 0 mA to 20 mA
Operating ambient temperature range (TA) ................................................................ -55C to +125C
1.5 Dissipation rating table. 4/
1/
2/
3/
4/
Case
outline
TA  25C
power rating
Derating factor
above TA = 25C
TA = 70C
power rating
TA = 80C
power rating
X
437 mW
3.5 mW/C
280 mW
227 mW
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
All voltages are within respect to device GND terminal.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
These dissipation ratings are based on EIA specification JESD51-3, “Low effective thermal conductivity test board for leaded
surface mount packages,” in test conducted in a zero airflow, wind tunnel environment.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC Solid State Technology Association
EIA/JEDEC 51-3 –
JEDEC PUB 95 –
Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
Registered and Standard Outlines for Semiconductor Devices
(Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107).
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions 2/
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics section
Positive going input
threshold voltage
Negative going input
threshold voltage
7
VCC = 14 V
10
All
-55C to +125C
VCC = 5 V
ICC
2
VCC = 14 V
2.5
Input = 0 V
V
1
VCC = 10 V
V
+25C
All
1.3 typical
V
+25C
01, 02
650 typical
A
15 typical
Input = VCC
03, 04,
05, 06
Input = 0 V or VCC
Input capacitance
4
VCC = 10 V
Input voltage
hysteresis
Input current
All
-55C to +125C
VCC = 5 V
CIN
-55C to +125C
All
-55C to +125C
All
0.2 typical
10
pF
Output characteristics section
High level output
voltage
IO = -1 mA
V
8
IO = -100 mA
Low level output
voltage
9.75
All
-55C to +125C
IO = 1 mA
0.25
V
2
IO = 100 mA
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions 2/
Temperature,
TA
Device
type
Limits
Unit
Min
Max
Regulator characteristics section
Output voltage
VOUT
-55C to +125C
01, 02,
03, 04
10
13
V
IO = 10 mA, VDD = 10 V
-55C to +125C
01, 02,
03, 04
8
10
V
IN = high = 10 V
-55C to +125C
01, 02
250
A
14 V  VDD  40 V,
0 mA  IO  20 mA
Output voltage in
dropout
Supply current characteristics section
Supply current into
VCC
Supply current into
VDD
IN = low = 0 V
1000
IN = high or low,
03, 04
55
high = 10 V, low = 0 V
05, 06
15
01, 02
1000
03, 04
400
-55C to +125C
VDD = 20 V,
IN = high = 10 V or low = 0 V
A
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions 2/
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Switching characteristics section
Rise time
Fall time
Propagation delay
time, high to low level
output
Propagation delay
time, low to high level
output
tr
tf
tPHL
tPLH
All
-55C to +125C
VCC = 14 V
25
VCC = 10 V
30
VCC = 5 V
35
All
-55C to +125C
VCC = 14 V
25
VCC = 10 V
30
VCC = 5 V
35
All
-55C to +125C
VCC = 14 V
45
VCC = 5 V
50
All
-55C to +125C
ns
40
VCC = 10 V
VCC = 14 V
ns
ns
40
VCC = 10 V
45
VCC = 5 V
50
ns
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
Unless otherwise specified, VCC = 10 V, VDD tied to VCC, and CL = 1 nF.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
7
Case X
FIGURE 1. Case outline.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
8
Case X - continued
Dimensions
Symbol
Inch
Millimeters
Min
Max
Min
Max
A
---
.057
---
1.45
A1
.000
.006
0.00
0.15
b
.011
.019
0.30
0.50
c
.003
.008
0.08
0.22
D
.108
.120
2.75
3.05
E
.057
.068
1.45
1.75
E1
.102
.118
2.60
3.00
e
L
.037 BSC
.011
0.95 BSC
.022
0.30
0.55
L1
.009 BSC
0.25 BSC
n
5 leads
5 leads
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed
0.15 mm (.006 inch) per side
3. Falls with JEDEC MO-178-AA.
FIGURE 1. Case outline – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
9
Device types
01, 02, 03, 04
05, 06
Case outline
X
Terminal number
Terminal symbol
1
VDD
NC
2
GND
GND
3
INPUT
INPUT
4
OUTPUT
OUTPUT
5
VCC
VCC
Device types
01, 03, 05 ( Inverting driver )
Terminal symbol
Description
VDD
Regulator supply voltage input.
( Not connected on device type 05 ).
GND
Ground.
INPUT
OUTPUT
VCC
Driver input.
Driver output, OUT = IN .
Driver supply voltage / regulator output voltage.
Device types
02, 04, 06 ( Noninverting driver )
Terminal symbol
Description
VDD
Regulator supply voltage input.
( Not connected on device type 06 ).
GND
Ground.
INPUT
OUTPUT
VCC
Driver input.
Driver output, OUT = IN.
Driver supply voltage / regulator output voltage.
FIGURE 2. Terminal connections.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
10
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Packaged devices
2/ 3/ 4/
Symbol
Chip form
(Y)
Vendor part number
V62/08601-01XE
5/
TPS2816DBV
TBD
TPS2816Y
TPS2816MDBVREP
V62/08601-02XE
5/
TPS2817DBV
TBD
TPS2817Y
TPS2817MDBVREP
V62/08601-03XE
01295
TPS2818DBV
PMTM
TPS2818Y
TPS2818MDBVREP
V62/08601-04XE
01295
TPS2819DBV
PMUM
TPS2819Y
TPS2819MDBVREP
V62/08601-05XE
5/
TPS2828DBV
TBD
TPS2828Y
TPS2828MDBVREP
V62/08601-06XE
5/
TPS2829DBV
TBD
TPS2829Y
TPS2829MDBVREP
1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering
documentation.
2/ For the most current package and ordering information, see the package option addendum at the end of this
document, or see manufacturer’s website.
3/ Package drawings, thermal data, and symbolization are available from the manufacturer.
4/ The DBV package is available taped and reeled only.
5/ Not available from an approved source.
CAGE code
01295
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Source of supply
Texas Instruments, Inc.
Semiconductor Group
8505 Forest Lane
P.O. Box 660199
Dallas, TX 75243
Point of contact: U.S. Highway 75 South
P.O. Box 84, M/S 853
Sherman, TX 75090-9493
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/08601
PAGE
11