REVISIONS LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV 1 PAGE 2 3 PMIC N/A PREPARED BY Phu H. Nguyen Original date of drawing YY MM DD CHECKED BY 08-08-04 Phu H. Nguyen APPROVED BY Thomas M. Hess SIZE A REV AMSC N/A 4 CODE IDENT. NO. 5 6 7 8 9 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, ULTRALOW-POWER NTSC/PAL/SECAM VIDEO DECODER, MONOLITHIC SILICON DWG NO. V62/08626 16236 PAGE 1 OF 9 5962-V060-08 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance ultralow-power NTSC/PAL/SECAM video decoder microcircuit, with an operating temperature range of -55°C to +125°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/08626 - Drawing number 01 X A Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 Circuit function TVP5150AM1-EP Ultralow-power NTSC/PAL/SECAM video decoder 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins Package style X 32 Plastic quad flatpack 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator A B C D E Z 1.3 Absolute maximum ratings. Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other 1/ Supply voltage range: IO_DVDD to DGND ...................................................................................................... DVDD to DGND ............................................................................................................ PLL_AVDD to PLL_AGND ............................................................................................ CH_AVDD to CH_AGND .............................................................................................. Digital input voltage range, VI to DGND ............................................................................... Input voltage range, XTAL1 to PLL_GND ............................................................................ Analog input voltage range A1 to CH_AGND ....................................................................... Digital output voltage range, VO to DGND ........................................................................... Storage temperature range, TSTG ......................................................................................... 1/ -0.5 V to 4.5 V -0.5 V to 2.3 V -0.5 V to 2.3 V -0.5 V to 2.3 V -0.5 V to 4.5 V -0.5 V to 2.3 V -0.2 V to 2.0 V -0.5 V to 4.5 V -65°C to 150°C Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 2 1.4 Recommended operating conditions. Digital I/O supply voltage, IO_DVDD .................................................................................... Digital supply voltage, DVDD ............................................................................................... Analog PLL supply voltage ................................................................................................... Analog core supply voltage, CH_AVDD ............................................................................... Analog input voltage (ac-coupling necessary), VI(P-P) ............................................................ Minimum digital input voltage high, VIH ................................................................................. Maximum digital input voltage low, VIL ................................................................................. Minimum XTAL input voltage high, VIH_XTAL .......................................................................... Maximum XTAL input voltage low, VIL_XTAL ........................................................................... Maximum high level output current, IOH .............................................................................. Maximum low level output current, IOL ................................................................................ Maximum SCLK high level output current, IOH_SCLK .............................................................. Maximum SCLK low level output current, IOL_SCLK ................................................................ Operating free air temperature ............................................................................................. 3.0 V to 3.6 V 1.65 V to 1.95 V 1.65 V to 1.95 V 1.65 V to 1.95 V 0 V to 0.75 V 0.7 IO_DVDD V 0.3 IO_DVDD V 0.7 PLL_AVDD V 0.3 PLL_AVDD V 2 mA -2 mA 4 mA -4 mA -55°C to 125°C 2. APPLICABLE DOCUMENTS JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industry Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or at http://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Functional block diagram. The functional block diagram shall be as shown in figure 3. 3.5.4 Timing waveforms. The timing waveforms shall be as shown in figure 4-5. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 3 TABLE I. Electrical performance characteristics. 1/ Test DC electrical characteristics 3/ 3.3 V I/O digital supply current 1.8 V digital supply current 1.8 V analog PLL supply current 1.8 V analog core supply current Total power dissipation, normal mode Total power dissipation, power down mode Input capacitance Output voltage high Output voltage low SCLK output voltage high SCLK output voltage low High level input current 6/ Low level input current 6/ Analog electrical characteristics Input impedance, analog video inputs Input capacitance, analog video inputs Input voltage range 7/ Gain control maximum Gain control minimum DC differential nonlinearity DC integral nonlinearity Frequency response Signal to noise ratio Noise spectrum Differential phase Differential gain Symbol IDD(IO_D) IDD(D) IDD(PLL_A) IDD(CH_A) PTOT 5/ Ci VOH VOL VOH_SCLK VOL_SCLK IIH IIL Zi Ci Vi(pp) ∆G ∆G DNL INL Fr SNR NS DP DG Conditions 2/ unless otherwise specified Color bar input Color bar input Color bar input Color bar input Color bar input Color bar input By design IOH = 2 mA IOL = -2 mA IOH = 4 mA IOL = -4 mA VI = VIH VI = VIL Limits Min Unit Max 4/ 4/ 4/ 4/ 4/ 10.0 32.9 7.1 36.0 160 mA mA mA mA mW mW pF V V V V µA µA 1 TYP 8 TYP 0.8 IO_DVDD 0.22 IO_DVDD 0.8 IO_DVDD 0.22 IO_DVDD ±28 ±28 By design By design Ccoupling = 0.1 µF 500 TYP 10 TYP 0 kΩ pF V dB dB LSB LSB dB dB dB º % 0.75 12 TYP 0 TYP A/D only A/D only 6 MHz, Specified by design 6 MHz, 1.0 VP-P 50% flat field ±1 ±2.5 -3 50 TYP 50 TYP 1.5 TYP 0.5 TYP See footnotes at end of table. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 4 TABLE I. Electrical performance characteristics – Continued. Test Clocks, Video data, Sync timing Symbol 8/ Conditions 2/ unless otherwise specified Unit Limits Min Max See figure 4 Duty cycle, PCLK % 50 TYP PCLK high time t1 ≥80% 16 22 PCLK low time t2 ≤20% 16 22 PCLK fall time t3 80% to 20% 4 TYP PCLK rise time t4 20% to 80% 4 TYP Output hold time t5 2 TYP Output delay time I2C host port timing 9/ t6 3 TYP ns See figure 5 Bus free time between Stop and Start t1 1.3 µs Setup time for a (repeated) Start condition t2 0.6 µs Hold time (repeated) Start condition t3 0.6 µs Setup time for a Stop condition t4 0.6 ns Data setup time t5 100 ns Data hold time t6 0 Rise time, VC1(SDA) and VC0(SCL) signal t7 250 0.9 µs ns ns Fall time, VC1(SDA) and VC0(SCL) signal t8 Capacitive load for each bus line Cb 400 pF I2C clock frequency fI2C 400 kHz 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 250 TYP Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. -55°C ≤ TA ≤ 125°C, DVDD = 1.8 V, PLL_AVDD = 1.8 V, CH_AVDD = 1.8 V, IO_DVDD = 3.3 V; for Typical value TA = 25°C unless otherwise noted. Measured with a load of 15 pF. For typical measurements only. Specified by device characterization. YOUT7 is a bidirectional terminal with an internal pull down resistor. This terminal may sink more than the specified current when in RESET mode. The 0.75 V maximum applies to the sync-chroma amplitude, not sync-white. The recommended termination resistor are 37.4 Ω, as seen in the manufacturer data book. Measured with a load of 15 pF. Specified by design. Specified by design for industrial temperature. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 5 Case X Symbol A A1 A2 A3 b C Dimension Millimeters Symbol Min Max 1.20 D/E 0.95 1.05 D1/E1 0.25 TYP D2/E2 0.05 0.15 e 0.17 0.23 L1 0.13 NOM Millimeters Min Max 6.90 7.10 4.95 5.05 3.50 TYP 0.50 BSC 0.40 0.70 NOTES: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. FIGURE 1. Case outline. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 6 Terminal number 1 2 3 4 5 6 7 8 Terminal symbol AIP1A AIP1B PLL_AGND PLL_AVDD XTAL1/OSC XTAL2 AGND RESETB Terminal number 9 10 11 12 13 14 15 16 Terminal symbol PCLK/SCLK IO_DVDD YOUT7/I2CSEL YOUT6 YOUT5 YOUT4 YOUT3 YOUT2 Case X Terminal number 17 18 19 20 21 22 23 24 Terminal symbol YOUT1 YOUT0 DGND DVDD SCL SDA FID/GLCO VSYNC/PALI Terminal number 25 26 27 28 29 30 31 32 Terminal symbol HSYNC AVID AVIDINTREQ/GPCL/VBLK PDN REFP REFM CH_AGND CH_AVDD FIGURE 2. Terminal connections. FIGURE 3. Functional block diagram. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 7 Clocks, Video data, and Sync Timing FIGURE 4. Timing waveforms. I2C Host port timing FIGURE 5. Timing waveforms. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 8 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/08626-01XE 01295 TVP5150AM1MPBSREP 5150MEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code 01295 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Source of supply Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 SIZE CODE IDENT NO. DWG NO. A 16236 V62/08626 REV PAGE 9