Previous Datasheet Index Next Data Sheet Bulletin I27400 IRK.430.. SERIES SUPER MAGN-A-PAK TM Power Modules THYRISTOR / DIODE and THYRISTOR / THYRISTOR Features 430 A High current capability 3000 VRMS isolating voltage with non-toxic substrate High surge capability High voltage ratings up to 2000V Industrial standard package UL recognition pending Typical Applications Motor starters DC motor controls - AC motor controls Uninterruptable power supplies Wind miles Major Ratings and Characteristics Parameters IRK.430.. Units IT(AV) or I F(AV) 430 A 82 °C 877 A 82 °C ITSM or I FSM @ 50Hz 15.7 KA @ 60Hz 16.4 KA @ 50Hz 1232 KA2s @ 60Hz 1125 KA2s 12320 KA2 √s 1600 to 2000 V @ TC IT(RMS) @ TC I2t I2√t V DRM/VRRM range T STG range - 40 to 150 °C TJ range - 40 to 130 °C To Order 1 Previous Datasheet Index Next Data Sheet IRK.430.. Series ELECTRICAL SPECIFICATIONS Voltage Ratings Type number IRK.430.. Voltage VRRM , maximum repetitive V RSM , maximum non- IRRM max. Code peak reverse voltage repetitive peak rev. voltage @ TJ = TJ max. V V mA 16 1600 1700 18 1800 1900 20 2000 2100 100 On-state Conduction Parameter IRK.430.. Units Conditions IT(AV) Maximum average on-state current 430 A IF(AV) @ Case temperature 82 °C IT(RMS) Maximum RMS on-state current 877 A ITSM Maximum peak, one-cycle, 15.7 KA IFSM non-repetitive surge current I2t Maximum I 2t for fusing I √t Maximum I √t for fusing 2 180° conduction, half sine wave @ TC = 82°C t = 10ms No voltage 16.4 t = 8.3ms reapplied 13.2 t = 10ms 100% VRRM 13.8 t = 8.3ms reapplied Sinusoidal half wave, t = 10ms No voltage Initial T J = T J max. 1125 t = 8.3ms reapplied 871 t = 10ms 100% VRRM t = 8.3ms reapplied 1232 KA2s 795 2 180° conduction, half sine wave 12320 VT(TO)1 Low level value of threshold voltage 0.96 VT(TO)2 High level value of threshold voltage 1.06 KA √s t = 0.1 to 10ms, no voltage reapplied 2 V (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. (I > π x IT(AV)), TJ = TJ max. rt1 Low level value of on-state slope resistance 0.51 mΩ rt2 High level value of on-state slope resistance 0.45 VTM Maximum on-state or forward 1.65 V VFM voltage drop IH Maximum holding current 500 mA IL Typical latching current 1000 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. (I > π x IT(AV)), TJ = TJ max. Ipk = 1500A, TJ = 25°C, tp = 10ms sine pulse TJ = 25°C, anode supply 12V resistive load Switching Parameter di/dt Maximum rate of rise of turned-on IRK.430.. Units Conditions 1000 A/µs TJ = TJ max., ITM = 400A, VDRM applied current td Typical delay time 2.0 µs Gate current 1A, di g/dt = 1A/µs Vd = 0.67% VDRM , TJ = 25°C tq Typical turn-off time 200 µs ITM = 750A, TJ = TJ max, di/dt = -60A/µs, VR = 50V, dv/dt = 20V/µs, Gate 0 V 100Ω To Order 2 Previous Datasheet Index Next Data Sheet IRK.430.. Series Blocking Parameter dv/dt IRK.430.. Maximum critical rate of rise of off-state Units Conditions 1000 V/µs T J = 130°C., linear to VD = 80% VDRM voltage VINS RMS isolation voltage 3000 V IRRM Maximum peak reverse and off-state 100 mA IDRM leakage current t=1s T J = TJ max., rated VDRM/V RRM applied Triggering Parameter IRK.430.. Units Conditions PGM Maximum peak gate power 10 W PG(AV) Maximum peak average gate power 2.0 W TJ = TJ max., tp < 5ms TJ = TJ max., f = 50Hz, d% = 50 + I GM Maximum peak positive gate current 3.0 A TJ = TJ max., tp < 5ms + V GM Maximum peak positive gate voltage 20 V - VGM Maximum peak negative gate voltage 5.0 V IGT Max. DC gate current required to trigger 200 mA TJ = 25°C Vak 12V VGT DC gate voltage required to trigger 3.0 V TJ = 25°C Vak 12V IGD DC gate current not to trigger 10 mA VGD DC gate voltage not to trigger 0.25 V TJ = TJ max. Thermal and Mechanical Specifications Parameter IRK.430.. TJ Max. junction operating temperature range - 40 to 130 Tstg Max. storage temperature range - 40 to 150 RthJC Max. thermal resistance, junction to Units Conditions °C 0.065 K/W 0.02 K/W 6-8 Nm Per junction, DC operation case RthC-hs Max. thermal resistance, case to heatsink T Mounting torque ± 10% SMAP to heatsink busbar to SMAP wt Approximate weight Case style 12 - 15 1500 g Super Magn-a-Pak To Order 3 A mounting compound is recommended and the torque should be rechecked after a period of 3 hours to allow for the spread of the compound See outline table Previous Datasheet Index Next Data Sheet IRK.430.. Series ∆RthJC Conduction (The following table shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction 180° 0.009 0.006 120° 0.011 0.011 90° 0.014 0.015 60° 0.021 0.022 30° 0.037 0.038 Units Conditions K/W TJ = TJ max. Ordering Information Table Device Code IRK T 430 1 2 3 - 20 4 1 - Module type 2 - Circuit configuration (See Circuit Configurations Table) 3 - Current rating 4 - Voltage code: Code x 100 = V RRM (See Voltage Ratings Table) Circuit Configurations Table IRKT IRKH IRKL 1 1 1 ~ + ~ + 2 2 3 - 3 - ~ + 2 4(K1) 7(K2) 4(K1) 3 7(K2) 5(G1) 6(G2) 5(G1) 6(G2) To Order 4 Previous Datasheet Index Next Data Sheet IRK.430.. Series Outline Table All dimensions in millimeters (inches) To Order 5