SANYO CPH6203

Ordering number:ENN5807
PNP/NPN Epitaxial Planar Silicon Transistors
CPH6103/CPH6203
High-Current Switching Applications
Applications
Package Dimensions
· DC-DC converter, relay drivers, lamp drivers, motor
drivers, strobes.
unit:mm
2146A
[CPH6103/6203]
0.15
2.9
· Adoption of FBET, MBIT processes.
· High current capacitance.
· Low collector-to-emitter saturation voltage.
· High-speed switching.
· Ultrasmall package permitting applied sets to be
made small and slim (0.9mm).
· High allowable power dissipation.
5
4
0.6
6
0.2
Features
2.8
0.6
1.6
0.05
3
0.95
1 : Collector
2 : Collector
3 : Base
4 : Emitter
5 : Collector
6 : Collector
SANYO : CPH6
0.2
2
0.7
0.9
1
( ) : CPH6103
0.4
Specifications
Absolute Maximum Ratings at Ta = 25˚C
Parameter
Symbol
Conditions
Ratings
Unit
Collector-to-Base Voltage
VCBO
(–)60
V
Collector-to-Emitter Voltage
VCEO
(–)50
V
Emitter-to-Base Voltage
VEBO
IC
(–)6
V
(–)2
A
ICP
(–)4
Collector Current
Collector Current (Pulse)
Base Current
IB
Collector Dissipation
Junction Temperature
PC
Tj
Storage Temperature
Tstg
(–)400
Mounted on a ceramic board (600mm2×0.8mm)
A
mA
1.3
W
150
˚C
–55 to +150
˚C
Electrical Characteristics at Ta = 25˚C
Parameter
Symbol
Conditions
Collector Cutoff Current
ICBO
Emitter Cutoff Current
IEBO
VCB=(–)50V, IE=0
VEB=(–)4V, IC=0
DC Current Gain
hFE
VCE=(–)2V, IC=(–)100mA
Gain-Bandwidth Product
fT
Cob
VCE=(–)10V, IC=(–)50mA
VCB=(–)10V, f=1MHz
Output Capacitance
Ratings
min
typ
200
max
Unit
(–)0.1
µA
(–)0.1
µA
400
150
(22)12
MHz
pF
Continued on next page.
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
D1099TS (KOTO) TA-1950 No.5807–1/4
CPH6103/CPH6203
Continued from preceding page.
Parameter
Symbol
Collector-to-Emitter Saturation Voltage
Conditions
VCE(sat)
Base-to-Emitter Saturation Voltage
IC=(–)1A, IB=(–)50mA
VBE(sat) IC=(–)1A, IB=(–)50mA
V(BR)CBO IC=(–)10µA, IE=0
V(BR)CEO IC=(–)1mA, RBE=∞
Collector-to-Base Breakdown Voltage
Collector-to-Emitter Breakdown Voltage
Emitter-to-Base Breakdown Voltage
Turn-ON Time
V(BR)EBO
ton
Storage Time
tstg
See specified test circuit.
tf
See specified test circuit.
Fall Time
Ratings
min
IC=(–)10µA, IC=0
See specified test circuit.
typ
max
Unit
(–0.3)
(–0.7)
mV
0.15
0.4
mV
(–)0.9
(–)1.2
V
(–)60
V
(–)50
V
(–)6
V
60(60)
ns
(450)
ns
550
ns
30(30)
ns
Switching Time Test Circuit
PW=20µs
D.C.≤1%
IB1
IB2
OUTPUT
INPUT
RB
RL
100µF
+
50Ω
+
VR
470µF
VBE=–5V
VCC=25V
10IB1=–10IB2=IC=500mA
(For PNP, the polarity is reversed.)
No.5807–2/4
CPH6103/CPH6203
No.5807–3/4
CPH6103/CPH6203
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be expor ted without obtaining the expor t license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of December, 1999. Specifications and information herein are subject
to change without notice.
PS No.5807–4/4