V6209614 VID

REVISIONS
LTR
DESCRIPTION
DATE
Prepared in accordance with ASME Y14.24
APPROVED
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
1
PAGE
2
PMIC N/A
PREPARED BY
RAJESH PITHADIA
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
08-12-18
4
A
REV
5
6
7
8
9
10
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
TITLE
MICROCIRCUIT, LINEAR, QUAD, PRECISION,
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
APPROVED BY
ROBERT M. HEBER
SIZE
AMSC N/A
3
CODE IDENT. NO.
DWG NO.
V62/09614
16236
PAGE
1
OF
10
5962-V021-09
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance quad, precision, operational amplifier
microcircuit, with an operating temperature range of -55°C to +125°C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/09614
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
LT1014
Circuit function
Quad, precision, operational amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
16
JEDEC PUB 95
Package style
MS-013-AA
Plastic small outline
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture:
Finish designator
A
B
C
D
E
Z
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage range (VCC) ........................................................................................
Differential input voltage range ...................................................................................
Input voltage range (any input) ...................................................................................
Duration of short-circuit current ..................................................................................
Continuous total power dissipation (PD) .....................................................................
Storage temperature range (TSTG)...............................................................................
Lead temperature (1.6 mm, at distance 1/16 inch from case for 10 seconds) ............
-22 V to 22 V 2/
-30 V to 30 V 3/
-VCC – 5 V to +VCC 2/
Unlimited 4/
See dissipation rating table
-65°C to 150°C
260°C
1.4 Recommended operating conditions. 5/
Operating free-air temperature range (TA) .................................................................. -55°C to +125°C
Dissipation rating table
Package
X
1/
TA ≤ 25°C
power rating
1025 mW
Derating factor
above TA = 25°C
8.2 mW/°C
TA = 70°C
power rating
TA = 105°C
power rating
TA = 125°C
power rating
656 mW
369 mW
205 mW
2/
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
All voltage values, except differential voltages, are with respect to the midpoint between +VCC and –VCC.
3/
Differential voltages are at the noninverting input with respect to the inverting input.
4/
The output may be shorted to either supply.
5/
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC PUB 95
–
Registered and Standard Outlines for Semiconductor Devices
(Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington,
VA 22201-3834 or online at http://www.jedec.org)
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions 2/
Temperature,
TA
Device
type
Min
Input offset voltage
VIO
RS = 50 Ω
RS = 50 Ω, VIC = 0.1 V
Input offset current
IIO
Max
01
+25°C
450
-55°C to +125°C
1500
+125°C
750
01
+25°C
2
IIB
01
+25°C
-50
VICR
01
+25°C
VOM
Large signal differential
voltage amplification
AVD
Supply current per
amplifier
ICC
0 to
3.5
V
Output low, no load
+25°C
Output low, RL = 600 Ω to GND
+25°C
10
-55°C to +125°C
18
Output low, ISINK = 1 mA
+25°C
350
Output high, no load
+25°C
4
Output high
+25°C
3.4
-55°C to +125°C
3.1
RL = 600 Ω to GND
VO = 5 mV to 4 V, RL = 500 Ω
nA
0.1 to
3
-55°C to +125°C
Maximum peak output
voltage swing
nA
-120
-55°C to +125°C
Common-mode input
voltage range
μV
10
-55°C to +125°C
Input bias current
Unit
Limits
01
+25°C
01
+25°C
01
-55°C to +125°C
25
mV
V
1 typical
0.5
V/μV
mA
0.65
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions 3/
Temperature,
TA
Device
type
Min
Slew rate
SR
Equivalent input noise
voltage
Vn
f = 10 Hz
+25°C
01
+25°C
01
f = 1 kHz
Unit
Limits
Max
0.2
V/μs
24 typical
nV/
Hz
22 typical
Peak-to-peak
equivalent input noise
voltage
VN(PP)
f = 0.1 Hz to 10 Hz
+25°C
01
0.55 typical
μV
Equivalent input noise
current
In
f = 10 Hz
+25°C
01
0.07 typical
pA/
Hz
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
Unless otherwise specified, +VCC = 5 V, -VCC = 0 V, VO = 1.4 V, VIC = 0 V.
3/
Unless otherwise specified, ±VCC =15 V, VIC = 0 V.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
6
Case X
FIGURE 1. Case outlines.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
7
Case X – continued.
Dimensions
Symbol
Inches
Millimeters
Min
Max
Min
Max
A
---
0.104
---
2.65
A1
0.004
0.012
0.10
0.30
b
0.012
0.020
0.31
0.50
c
0.008
0.013
0.20
0.33
D
0.398
0.413
10.10
10.50
E
0.291
0.299
7.40
7.60
E1
0.393
0.419
9.97
10.63
e
L
0.050 NOM
0.016
n
1.27 NOM
0.050
0.40
16
1.27
16
NOTES:
1. Controlling dimensions are inch, millimeter dimensions are given for reference only.
2. Body length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not
exceed 0.006 inch (0.15 mm) per end.
3. Falls within reference to JEDEC MS-013-AA.
FIGURE 1. Case outlines – continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
8
Device type
01
Case outlines
X
Terminal number
Terminal
symbol
1
1OUT
2
1IN-
3
1IN+
4
+VCC
5
2IN+
6
2IN-
7
2OUT
8
NC
9
NC
10
3OUT
11
3IN-
12
3IN+
13
-VCC/GND
14
4IN+
15
4IN-
16
4OUT
FIGURE 2. Terminal connections.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
9
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Vendor part number
V62/09614-01XE
01295
LT1014DMDWREP
1/ The vendor item drawing establishes an administrative control number
for identifying the item on the engineering documentation.
CAGE code
01295
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Source of supply
Texas Instruments, Inc.
Semiconductor Group
8505 Forest Lane
P.O. Box 660199
Dallas, TX 75243
Point of contact: U.S. Highway 75 South
P.O. Box 84, M/S 853
Sherman, TX 75090-9493
SIZE
CODE IDENT NO.
DWG NO.
A
16236
V62/09614
REV
PAGE
10