INTEGRATED CIRCUITS DATA SHEET TDA8732 NICAM-728 demodulator (NIDEM) Product specification File under Integrated Circuits, IC02 April 1993 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 FEATURES GENERAL DESCRIPTION • 5 V supplies for analog and digital circuitry The NIDEM is a dedicated device providing a DQPSK (Differential Quadrature Phase Shift Keying) demodulator for a NICAM-728 system. The device interfaces with NICAM-728 decoders and provides data synchronized to a 728 kHz clock (either supplied externally or by the on-board clock). The device consists of a costas loop quadrature demodulator, a bit-rate clock recovery and differential decoder with parallel-to-serial conversion. The Voltage Controlled Oscillator (VCO) used in the costas loop is achieved with a single-pin crystal oscillator. A second single-pin crystal oscillator with a divider chain provides signals at 5.824 MHz and at 728 kHz. The NIDEM is suitable for PAL B and G (carrier oscillator crystal at 11.7 MHz) and PAL I (carrier oscillator crystal at 13.104 MHz). • Low cost application • Improved noise behaviour • Limiting amplifier for QPSK input • Suitable with PAL B, G and I NICAM-728 systems. APPLICATIONS • NICAM-728 systems. QUICK REFERENCE DATA Measured over full voltage and temperature ranges. SYMBOL PARAMETER MIN. TYP. MAX. UNIT VCCA analog supply voltage 4.5 5 5.5 V VCCD digital supply voltage 4.5 5 5.5 V VCCA analog supply voltage 4.5 5 5.5 V VCCA−VCCD differential supply voltage −0.5 − 0.5 V ICCA analog supply current − 12.5 − mA ICCD digital supply current − 14.5 − mA V3 QPSK input level (peak-to-peak value) 30 100 300 mV RI input resistance 1.75 2.5 3.25 kΩ CI input capacitance − 2 − pF fCAROSC carrier oscillator frequency 11.5 − 13.5 MHz fXTAL crystal frequency PAL B, G − 11.7 − MHz PAL I − 13.104 − MHz fCLKOSC clock oscillator frequency − 11.648 − MHz fC5M C5M output frequency − 5.824 − MHz ORDERING INFORMATION EXTENDED TYPE NUMBER TDA8732 PACKAGE PINS PIN POSITION MATERIAL CODE 20 DIL plastic SOT146(1) Note 1. SOT146-1; 1996 December 3. April 1993 2 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 Fig.1 Block diagram. April 1993 3 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 PINNING SYMBOL PIN DESCRIPTION CLKLPF 1 transconductance output for bit-rate loop low-pass filter VEEA 2 ground for analog circuitry QPSKIN 3 QPSK modulated data input VCCA 4 power supply for analog circuitry CFI 5 baseband cosine channel input after filtering CFO 6 demodulated cosine channel output to low-pass filter SFO 7 demodulated sine channel output to low-pass filter SFI 8 baseband sine channel input after filtering CARLPF 9 transconductance output for carrier loop low-pass filter CAROSC 10 crystal input for carrier oscillator (frequency is 11.7 MHz or 13.104 MHz) QMC 11 monostable components connection for quadrature data transition detector VCCD 12 power supply for digital circuitry IMC 13 monostable components connection for in-phase data transition detector VEED 14 ground for digital circuitry DATA 15 728 kbit/s demodulated and differentially decoded serial data output CLKIN 16 bit-rate clock input at 728 kHz, phase-locked to the data CLK 17 output clock frequency at 728 kHz C5M 18 reference frequency output at 5.824 MHz (8 x CLK) TEST 19 input for test purpose (grounded for normal operation) CLKOS 20 crystal input for clock oscillator (frequency is 11.648 MHz) April 1993 4 Fig.2 Pin configuration. Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 FUNCTIONAL DESCRIPTION Clock oscillator and timing generator QPSK demodulator A voltage-controlled oscillator on-board the NIDEM operates at 11.648 MHz and is divided down to produce a 728 kHz (bit-rate) clock output (CLK) which is phase locked to the pulse stream and may be used as an alternative clock input for NIDEM. A reference clock at 5.824 MHz is provided at pin C5M (TTL levels). The DQPSK signal input to the demodulator (QPSKIN) is limited and fed into the costas loop demodulator. A single-pin carrier oscillator (CAROSC), at twice the carrier frequency, supplies a differential signal to the divider circuitry, which drives the demodulators with both 0° and 90° phase shift. This produces cosine and sine signals which are required for the carrier recovery. Cosine (in-phase) and sine (in Quadrature) channel baseband filters are then provided externally between pins CFO and CFI, and SFO and SFI respectively. The two filtered baseband signals are then processed to provide an error signal, the magnitude and which of which bear a fixed relationship to the phase error of the carrier, regardless of which of the four rest-states the signal occupies. The carrier recovery loop is closed with the aid of a single pin loop filter connection at CARLPF, which filters the error voltage signal to control the 728 kHz as shown in application diagrams Fig.4 and 5. Differential decoder and parallel-to-serial converter The recovered symbol-rate clocking-signal (364 kHz) produced internally is passed to the demodulator where it samples the sliced raised cosine pulse stream. The recovered bit-rate clocking-signal is passed to the decoder and is used to differentially decode the demodulated data signal and reform it into a serial bit-stream. Bit-rate clock recovery loop The CFI and SFI channels are processed using edge detectors and monostables, with externally derived time constants (see Fig.3), to generate a signal with a coherent component at the data bit symbol rate. This signal is compared with the clock derived from CLKIN and used to produce an error signal at the transconductance output CLKLPF. This error signal is loop-filtered and used to control the clock generator (at CLKOSC if the on-board clock is used; see Fig.5). April 1993 5 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL PARAMETER MIN. MAX. UNIT VCCA analog supply voltage −0.3 6 V VCCD digital supply voltage −0.3 6 V QPSKIN modulated data input voltage −0.3 5.5 V CFI baseband cosine channel input voltage −0.3 VCCA V SFI baseband sine channel input voltage −0.3 VCCA V CFO demodulated cosine channel output voltage −0.3 5.5 V SFO demodulated sine channel output voltage −0.3 5.5 V CAROSC crystal input voltage for carrier oscillator −0.3 5.5 V CLKOSC crystal input voltage for clock oscillator −0.3 5.5 V QMC,IMC monostable output voltage −0.3 VCCD V DATA data output voltage −0.3 5.5 V CLK clock output voltage −0.3 5.5 V C5M reference frequency output voltage −0.3 5.5 V CLKIN bit-rate clock input voltage −0.3 6 V TEST input voltage for test purpose −0.3 6 V CLKLPF bit-rate loop output voltage −0.3 5.5 V CARLPF carrier loop output voltage −0.3 5.5 V Tamb operating ambient temperature 0 70 °C Tstg storage temperature −40 +125 °C Tj maximum junction temperature − +125 °C THERMAL RESISTANCE SYMBOL Rth j-a April 1993 PARAMETER from junction to ambient in free air THERMAL RESISTANCE 80 K/W 6 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 CHARACTERISTICS VCCA = 5 V ± 10%; VCCD = 5 V ± 10%; −0.5 V < VCCA − VCCD < 0.5 V; Tamb = 0 to 70 °C; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply VCCA analog supply voltage 4.5 5 5.5 V VCCD digital supply voltage 4.5 5 5.5 V −0.5 − 0.5 V VCCA−VCCD differential supply voltage ICCA analog supply current − 13 17 mA ICCD digital supply current − 13 17 mA Ptot total power dissipation − 130 187 mW Inputs CLKIN VIH HIGH level input voltage 2 − VCCD V VIL LOW level input voltage − − 0.8 V IIH HIGH level input current VI = 5 V − − 10 µA IIL LOW level input current VI = 0 V −400 − − µA 5 − 7 MHz QPSKIN fQPSKIN input frequency RI input resistance f = 6 MHz 1.75 2.5 3.25 kΩ CI input capacitance f = 6 MHz − 2 − pF Ib input bias current VSFI = 4.3 V; VCFI = 4.3 V − − 5 µA RI input resistance f = 364 kHz 70 100 130 kΩ CI input capacitance f = 364 kHz − 2 − pF 11.5 − 13.5 MHz SFI, CFI CAROSC fcar oscillator frequency CARRIER OSCILLATOR CRYSTAL holder nominal frequency with specified load RW 43 CL = 15 pF fPAL I PAL I − 13.104 − MHz fPAL B, G PAL B, G − 11.7 − MHz adjustment tolerance on frequency at 25 °C −30 − +30 10−6 temperature 0 − 70 °C frequency stability over temperature −30 − +30 10−6 load capacitance − 15 − pF CL April 1993 vibration mode fundamental circuit condition series resonance 7 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) SYMBOL PARAMETER TDA8732 CONDITIONS MIN. TYP. MAX. UNIT 15 − 40 Ω motional capacitance − 21 − fF parallel capacitance − − 5 pF drive power level − − 0.5 mW − 11.648 − MHz Rs resonance resistance Cm Cp note 1 CLKOSC fclk oscillator frequency Cl = 15 pF BIT-RATE OSCILLATOR CRYSTAL holder nominal frequency with specified load RW 43 CL = 15 pF fPAL I PAL I − 11.648 − MHz fPAL B, G PAL B, G − 11.648 − MHz adjustment tolerance on frequency at 25 °C −30 − +30 10−6 temperature 0 − 70 °C frequency stability over temperature −30 − +30 10−6 CL load capacitance − 15 − pF Rs resonance resistance 15 − 40 kΩ Cm motional capacitance − 21 − fF Cp parallel capacitance − − 5 pF drive level − − 0.5 mW − 110 200 Ω 0.8 1 − V IOL = 100 µA − − 0.4 V vibration mode fundamental circuit condition series resonance note 1 Outputs CFO, SFO RO output impedance Vamp signal amplitude (peak-to-peak value) f = 364 kHz CARLPF VOL LOW level output voltage VOH HIGH level output voltage IOH = −100 µA VCCD−1 V − − V gm φ1 phase comparator transconductance gain VO = 0.4 V to VCCD − 1 V 100 125 − µA/rd ILO output leakage current for π/4 phase shift −5 − 5 µA − − 0.4 V CLKLPF VOL April 1993 LOW level output voltage IOL = 100 µA 8 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) SYMBOL PARAMETER TDA8732 CONDITIONS MIN. TYP. MAX. UNIT VOH HIGH level output voltage IOH = −100 µA VCCD−1 V − − V gm φ2 phase comparator transconductance gain VO = 0.4 V to VCCD−1 V 50 65 − µA/rd ILO off-state output leakage current −5 − 5 µA IMC, QMC (TYPICAL RC NETWORK; R = 22 KΩ; C = 150 PF) tREC monostable recovery time − − 600 ns ton monostable time − 1.37 − µs CLK, C5M VOL LOW level output voltage IOL = 1 mA − − 0.4 V VOH HIGH level output voltage IOH = −100 µA 2.4 − VCCD V tr rise time CL = 15 pF; see Fig.3 − 20 − ns tf fall time CL = 15 pF; see Fig.3 − 20 − ns fC5M C5M reference frequency − 5.824 − MHz DATA VOL LOW level output voltage IOL = 1 mA − − 0.4 V VOH HIGH level output voltage IOH = −100 µA 2.4 − VCCD V tr rise time CL = 15 pF; see Fig.3 − 30 − ns tf fall time CL = 15 pF; see Fig.3 − 30 − ns CLOCK TIMING td CLK to C5M delay (pin 17 to 18) − 15 − ns td CLKIN to DATA delay (pin 16 to 15) VCCD = 4.5 V − 520 585 ns Note 1. Only the maximum value is relevant with a 15 Ω resistor in series with the crystal (due to the application requirements). April 1993 9 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 Fig.3 Data timing diagram. April 1993 10 (1) PAL I: 13.104 MHz PAL B or G: 11.700 MHz (2) 17.472 MHz (3) TH316BQM-3223QDBP (PAL B or G) TH316BQM-3224QDBP (PAL I) (4) The 100 nF capacitor must be placed as close as possible to the package. Fig.4 Typical application diagram with the SAA7280. Philips Semiconductors April 1993 Product specification NICAM-728 demodulator (NIDEM) TDA8732 11 (1) PAL I: 13.104 MHz PAL B or G: 11.700 MHz (2) 11.648 MHz (3) TH316BQM-3223QDBP (PAL B or G) TH316BQM-3224QDBP (PAL I) (4) The 100 nF capacitor must be placed as close as possible to the package. Fig.5 Typical application diagram with a NICAM decoder. Philips Semiconductors April 1993 Product specification NICAM-728 demodulator (NIDEM) TDA8732 12 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 PACKAGE OUTLINE DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 11 20 pin 1 index E 1 10 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c mm 4.2 0.51 3.2 1.73 1.30 0.53 0.38 0.36 0.23 26.92 26.54 inches 0.17 0.020 0.13 0.068 0.051 0.021 0.015 0.014 0.009 1.060 1.045 D e e1 L ME MH w Z (1) max. 6.40 6.22 2.54 7.62 3.60 3.05 8.25 7.80 10.0 8.3 0.254 2.0 0.25 0.24 0.10 0.30 0.14 0.12 0.32 0.31 0.39 0.33 0.01 0.078 (1) E (1) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT146-1 April 1993 REFERENCES IEC JEDEC EIAJ SC603 13 EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-05-24 Philips Semiconductors Product specification NICAM-728 demodulator (NIDEM) TDA8732 with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. April 1993 14