NIKO-SEM 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) L1117 Series SOT-223, TO-252, TO-220,TO-263 GENERAL DESCRIPTION FEATURES The L1117 Series are positive and low dropout three-terminal voltage regulators with 1A output current capability. These devices are designed for use in low voltage applications that offers lower dropout voltage and faster transient response. z Fixed 2.5V, 2.85V, 3.3V, 5V or adjustable output voltage z Low dropout voltage: 1.2V typical at up to 1A z Low ground current z Fast transient response z Current & thermal limiting z Line regulation: 0.5% typical z Load regulation: 0.5% typical zSOT-223,TO-220,TO-252,TO-263 package These devices are fully protected against over current faults, over temperature operation, reversed input polarity, reversed lead insertion, transient voltage spike …etc. On-Chips trimming the reference voltage to 2% and features the low dropout of maximum 1.45 volts. APPLICATIONS z 2.85V active SCSI terminators z 8-15V to 5V linear regulators z 5V to 2.5V or 3.3V linear regulators z Low voltage micro-controllers z Battery Chargers z Motherboard clock supplies z Post regulator for switching supplies z Micro-controllers The L1117 Series regulators offer fixed and adjustable voltage options available in the popular industry standard SOT-223, TO-220, TO-252 and TO-263 packages. ABSOLUTE MAXIMUM RATINGS z Maximum Supply Voltage z Power Dissipation z Thermal Resistance Junction to Case, θJC z Thermal Resistance Junction to Ambient, θJA SOT-223 TO-252 TO-220 TO-263 z Operating Junction Temperature Range z Storage Temperature Range z Lead Temperature (Soldering, 10 Seconds) 15V* Internally Limited 16 °C/W 0 to 125 °C -40 to 150 °C 260 °C 158 °C/W 70 °C/W 50 °C/W 60 °C/W * When considering short circuits to ground, the maximum input-to-output differential voltage shall not be allowed greater than approximate 2~3V at values of supply voltage in excess of 10V, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. 1 JUL-27-2001 L1117 Series 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) NIKO-SEM SOT-223, TO-252, TO-220,TO-263 ELECTRICAL CHARACTERISTICS for ADJUSTABLE(Unless otherwise specified, TA = 25°C) Parameter Symbol Test Conditions Reference Voltage (Adjustable version) VREF VIN = 5V, IOUT = 10mA Output Voltage VO VIN = 5V, IOUT = 10mA (Fixed version) Dropout Voltage VD ΔVREF = 1%, IOUT = 1A Line Regulation REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 15V, IOUT = 10mA Load Regulation REG(LOAD) (VIN -VOUT) = 2V, 10mA ≤ IOUT ≤ 1A Minimum Load Current IO Adjust Pin Current Current Limit IADJ ICL RMS Output Noise VN Ripple Rejection Ratio RA 1.5V ≤ (VIN -VOUT) ≤ 5.75V VIN - VOUT = 2V f = 120Hz, CADJ = 22µF for ADJ pin, VIN = 5V, IOUT = 1A Typical 1.25V VO 1.2V 0.5% 0.5% Limits 1.23VMin 1.27VMax 0.98VO(Min) 1.02VO(Max) 1.45V 2% 2.5% 10mA 55µA 1.2A 0.003% of VOUT 100µA 1.1A (Min) 72dB 60dB (Min) ELECTRICAL CHARACTERISTICS for L1117-2.5(Unless otherwise specified, TA = 25 °C) Parameter Output Voltage (Fixed version) Dropout Voltage Line Regulation Load Regulation Minimum Load Current GND Pin Current Current Limit Symbol VO Test Conditions VIN = 5V, IOUT = 10mA VD ΔVO = 1%, IOUT = 1A REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 15V, IOUT = 10mA REG(LOAD) (VIN -VOUT) = 2V, 10mA ≤ IOUT ≤ 1A IO IGND ICL RMS Output Noise VN Ripple Rejection Ratio RA 1.5V ≤ (VIN -VOUT) ≤ 5.75V VIN - VOUT = 2V f = 120Hz, Co=22Uf,VIN = 5V, IOUT = 1A 2 Typical VO 1.2V 0.5% 0.5% Limits 2.45V(Min) 2.55V(Max) 1.45V 2.0% 2.0% 10mA 55µA 1.2A 0.003% of VOUT 100µA 1.1A (Min) 72dB 60dB (Min) JUL-27-2001 L1117 Series 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) NIKO-SEM SOT-223, TO-252, TO-220,TO-263 ELECTRICAL CHARACTERISTICS for L1117-2.85(Unless otherwise specified, TA = 25 °C) Parameter Output Voltage (Fixed version) Dropout Voltage Line Regulation Load Regulation Minimum Load Current GND Pin Current Current Limit Symbol VO Test Conditions VIN = 5V, IOUT = 10mA Typical VO VD ΔVO = 1%, IOUT = 1A REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 8V, IOUT = 10mA REG(LOAD) (VIN -VOUT) = 2V, 10mA ≤ IOUT ≤ 1A 1.2V 0.5% 0.5% 1.5V ≤ (VIN -VOUT) ≤ 5.75V 10mA IO IGND ICL RMS Output Noise VN Ripple Rejection Ratio RA VIN - VOUT = 2V f = 120Hz, Co=22Uf,VIN = 5V, IOUT = 1A Limits 2.793V(Min) 2.907V(Max) 1.45V 2.0% 2.0% 55µA 1.2A 0.003% of VOUT 100µA 1.1A (Min) 72dB 60dB (Min) ELECTRICAL CHARACTERISTICS for L1117-3.3(Unless otherwise specified, TA = 25 °C) Parameter Output Voltage (Fixed version) Dropout Voltage Line Regulation Load Regulation Minimum Load Current GND Pin Current Current Limit Symbol VO Test Conditions VIN = 5V, IOUT = 10mA VD ΔVO = 1%, IOUT = 1A REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 15V, IOUT = 10mA REG(LOAD) (VIN -VOUT) = 2V, 10mA ≤ IOUT ≤ 1A IO IGND ICL RMS Output Noise VN Ripple Rejection Ratio RA 1.5V ≤ (VIN -VOUT) ≤ 5.75V VIN - VOUT = 2V f = 120Hz, Co=22Uf,VIN = 5V, IOUT = 1A 3 Typical VO 1.2V 0.5% 0.5% Limits 3.234V(Min) 3.367V(Max) 1.45V 2.0% 2.0% 10mA 55µA 1.2A 0.003% of VOUT 100µA 1.1A (Min) 72dB 60dB (Min) JUL-27-2001 L1117 Series 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) NIKO-SEM SOT-223, TO-252, TO-220,TO-263 ELECTRICAL CHARACTERISTICS for L1117-5(Unless otherwise specified, TA = 25 °C) Parameter Symbol Output Voltage (Fixed version) Dropout Voltage Line Regulation Load Regulation VO Test Conditions Typical VIN = 8V, IOUT = 10mA VO VD ΔVO = 1%, IOUT = 1A REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 15V, IOUT = 10mA REG(LOAD) (VIN -VOUT) = 2V, 10mA ≤ IOUT ≤ 1A Minimum Load Current IO GND Pin Current Current Limit IGND ICL RMS Output Noise VN Ripple Rejection Ratio RA 1.5V ≤ (VIN -VOUT) ≤ 5.75V 1.2V 0.5% 0.5% Limits 4.90V(Min) 5.10V(Max) 1.45V 1.0% 1.0% 10mA VIN - VOUT = 2V f = 120Hz, Co=22uf,VIN = 8V, IOUT = 1A 55µA 1.2A 0.003% of VOUT 100µA 1.1A (Min) 72dB 60dB (Min) DEVICE SELECTION GUIDE L1117L ADJ SOT-223 L1117L L1117D ADJ TO-252 L1117D L1117L-2.5 L1117L-2.85 L1117L-3.3 L1117D-3.3 L1117L-5 2.5 2.85 3.3 3.3 5 SOT-223 SOT-223 SOT-223 TO-252 SOT-223 L1117L-2.5 L1117L-2.85 L1117L-3.3 L1117D-3.3 L1117L-5 L1117D-5 Device 5 Voltage Version TO-252 Package L1117D-5 Marking L1117T ADJ TO-220 L1117T L1117T-3.3 3.3 TO-220 L1117T-3.3 Device Voltage Version Package Marking L1117T-5 5 TO-220 L1117T-5 4 L1117S-5 5 TO-263 L1117S-5 JUL-27-2001 L1117 Series 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) NIKO-SEM SOT-223, TO-252, TO-220,TO-263 TYPICAL APPLICATION Vin Vin Vout L1117 IN ADJ Cin 4.3v-8V OUT Vref IN OUT L1117-2.85 R1 + + 10uF GND Cout Cin 10uF 10uF + Cout 18~27 Lines + 22uF R2 Iadj Vo = Vref (1+R2/R1) + Iadj x R2 1. Cin needed if device is far from from filter capacitors. 2. Cout required for stability. - Basic Adjustable Regulator Circuit - Vin > 4.75V Vout=3.3V IN Cin 10uF - Active SCSI Bus Terminators - L1117-3.3 GND + Vin > 4.00V OUT Cout 22uF Vout=2.5V IN + RL Cin 10uF Basic Fixed Output Regulator Circuit L1117-2.5 GND + OUT Cout 22uF + RL Basic Fixed Output Regulator Circuit Vin>6.5V IN Cin 10uF L1117-5 GND + OUT Cout 22uF + RL Basic Fixed Output Regulator Circuit 5 JUL-27-2001 NIKO-SEM 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) L1117 Series SOT-223, TO-252, TO-220,TO-263 PIN CONFIGURATIONS Pin # Function 1 Adjust/Ground 2 Output 3 Input Note: TAB is Output Pin 6 JUL-27-2001 NIKO-SEM 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) L1117 Series SOT-223, TO-252, TO-220,TO-263 SOT-223 MECHANICAL DATA mm Dimension mm Min. Typ. Max. A 0.67 0.7 0.73 B 6.7 7 C 2.9 D Dimension Min. Typ. Max. H 3.3 3.5 3.7 7.3 I 0.63 0.65 0.67 3 3.1 J 0.32 0.4 2.27 2.3 2.33 K 0° 10° E 4.57 4.6 4.63 L 0.03 0.1 F 1.5 1.6 1.7 M G 6.3 6.5 6.7 N 7 JUL-27-2001 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) NIKO-SEM L1117 Series SOT-223, TO-252, TO-220,TO-263 TO-252 (DPAK) MECHANICAL DATA mm Dimension Min. Typ. mm Max. Dimension Min. Typ. Max. A 9.35 10.1 H B 2.2 2.4 I 6.4 6.6 C 0.48 0.6 J 5.2 5.4 D 0.89 1.5 K 0.6 1 E 0.45 0.6 L 0.64 0.9 F 0.03 0.23 M 4.4 4.6 G 6 6.2 N 8 0.8 JUL-27-2001 NIKO-SEM 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) L1117 Series SOT-223, TO-252, TO-220,TO-263 TO-220 (3-Lead) MECHANICAL DATA mm Dimension mm Min. Typ. Max. A 9.78 10.16 10.54 B 2.61 2.74 2.87 C Dimension 20 Min. Typ. Max. H 2.4 2.54 2.68 I 1.19 1.27 1.35 J 4.4 4.6 4.8 D 28.5 28.9 29.3 K 1.14 1.27 1.4 E 14.6 15.0 15.4 L 2.3 2.6 2.9 F 8.4 8.8 9.2 M 0.26 0.46 0.66 G 0.72 0.8 0.88 N 9 7° JUL-27-2001 NIKO-SEM 1A Fixed and Adjustable Low Dropout Linear Regulator (LDO) L1117 Series SOT-223, TO-252, TO-220,TO-263 TO-263 (D2PAK) MECHANICAL DATA mm Dimension mm Min. Typ. Max. A 14.5 15 15.8 B 4.2 C 1.20 D Dimension Min. Typ. Max. H 1.0 1.5 1.8 4.7 I 9.8 1.35 J 6.5 K 1.5 2.8 E 0.3 F -0.102 G 8.5 0.4 9 0.5 L 0.7 0.203 M 4.83 9.5 N 10 10.3 1.4 5.08 5.33 JUL-27-2001