SEMICONDUCTOR TECHNICAL DATA The MC10E/100E131 is a quad master-slave D-type flip-flop with differential outputs. Each flip-flop may be clocked separately by holding Common Clock (CC) LOW and using the Clock Enable (CE) inputs for clocking. Common clocking is achieved by holding the CE inputs LOW and using CC to clock all four flip-flops. In this case, the CE inputs perform the function of controlling the common clock, to each flip-flop. Individual asynchronous resets are provided (R). Asynchronous set controls (S) are ganged together in pairs, with the pairing chosen to reflect physical chip symmetry. Data enters the master when both CC and CE are LOW, and transfers to the slave when either CC or CE (or both) go HIGH. • • • • • • • 4-BIT D FLIP-FLOP 1100MHz Min. Toggle Frequency Differential Outputs Individual and Common Clocks Individual Resets (asynchronous) Paired Sets (asynchronous) FN SUFFIX PLASTIC PACKAGE CASE 776-02 Extended 100E VEE Range of – 4.2V to – 5.46V 75kΩ Input Pulldown Resistors Pinout: 28-Lead PLCC (Top View) R3 D2 CE2 R2 VCCO Q3 Q3 25 24 23 22 21 20 19 LOGIC DIAGRAM S CE3 26 18 Q2 D3 D3 27 17 Q2 CE3 D R S12 28 16 VCC VEE 1 15 Q1 CC 2 14 Q1 S03 3 13 Q0 D0 4 12 Q0 5 6 7 8 9 10 11 CE0 R0 D1 CE1 R1 NC VCCO * All VCC and VCCO pins are tied together on the die. Pin D0 – D3 CE0 – CE3 R0 – R3 CC S03, S12 Q0 – Q3 Q0 – Q3 D2 S D CE2 R Q Q3 Q Q2 Q Q2 Q Q1 Q Q1 Q Q0 Q Q0 R2 S03 S12 CC R1 R CE1 D S Function Data Inputs Clock Enables (Individual) Resets Common Clock Sets (paired) True Outputs Inverting Outputs R0 R CE0 D0 7/96 Motorola, Inc. 1996 Q3 R3 D1 PIN NAMES Q 2–1 REV 3 D S MC10E131 MC100E131 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) –40°C Symbol IIH IIEE Characteristic Input HIGH Current Min Typ 0°C Max Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit Cond µA 350 450 300 150 CC S R, CE D Power Supply Current 10E 100E 350 450 300 150 350 450 300 150 350 450 300 150 mA 58 58 70 70 58 58 70 70 58 58 70 70 58 67 70 81 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) –40°C Symbol 0°C to 85°C Characteristic Min Typ fMAX tPLH tPHL Maximum Toggle Frequency 1000 1400 CE CC R S 310 275 300 300 600 600 625 550 tS tH Setup Time D 200 20 150 20 ps 1 Hold Time D 225 –20 175 –20 ps 1 tRR tPW Reset Recovery Time 450 150 400 150 ps tSKEW tr/tf Within-Device Skew Propagation Delay to Output Minimum Pulse Width Rise/Fall Time CLK R, S Max 750 725 775 775 400 400 Min Typ 1100 1400 360 325 350 350 500 500 550 550 460 700 675 725 725 300 Condition ps ps 60 725 Unit MHz 400 400 60 275 Max 480 675 ps 2 ps 20–80% 1. Setup/hold times guaranteed for both CC and CE. 2. Within-device skew is defined as identical transitions on similar paths through a device. MOTOROLA 2–2 ECLinPS and ECLinPS Lite DL140 — Rev 4 MC10E131 MC100E131 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776–02 ISSUE D 0.007 (0.180) B Y BRK -N- T L –M M U 0.007 (0.180) X G1 M S N T L –M S S N S D Z -L- -M- D W 28 V 1 C A 0.007 (0.180) M R 0.007 (0.180) M T L –M S T L –M S N S N S H S N S 0.007 (0.180) M T L –M N S S 0.004 (0.100) G J -T- K SEATING PLANE F VIEW S G1 T L –M S N 0.007 (0.180) M T L –M S N S VIEW S S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). ECLinPS and ECLinPS Lite DL140 — Rev 4 T L –M K1 E S S VIEW D-D Z 0.010 (0.250) 0.010 (0.250) 2–3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 — 0.025 — 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 — 0.020 2° 10° 0.410 0.430 0.040 — MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 — 0.64 — 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 — 0.50 2° 10° 10.42 10.92 1.02 — MOTOROLA MC10E131 MC100E131 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–4 *MC10E131/D* MC10E131/D ECLinPS and ECLinPS Lite DL140 — Rev 4