SEMICONDUCTOR TECHNICAL DATA The MC10E/100E107 is a quint 2-input XOR/XNOR gate. The function output F is the OR of all five XOR outputs, while F is the NOR. The Q outputs need not be terminated if only the F outputs are to be used. • • • • 600ps Max. Propagation Delay OR/NOR Function Outputs QUINT 2-INPUT XOR/XNOR GATE Extended 100E VEE Range of – 4.2V to – 5.46V 75kΩ Input Pulldown Resistors Pinout: 28-Lead PLCC (Top View) D3a D4b D4a NC VCCO F F 25 24 23 22 21 20 19 D3b 26 18 Q4 D2a 27 17 Q4 D2b 28 16 VCC VEE 1 15 Q3 D1a 2 14 Q3 D1b 3 13 Q2 D0a 4 12 Q2 5 6 D0b VCCO 7 8 9 10 11 Q0 Q0 Q1 Q1 VCCO * All VCC and VCCO pins are tied together on the die. PIN NAMES Pin Function FN SUFFIX PLASTIC PACKAGE CASE 776-02 F LOGIC DIAGRAM F D0a Q0 D0b Q0 D1a Q1 D1b Q1 D0a – D4b Data Inputs Q0 – Q4 XOR Outputs D2a Q2 Q0 – Q4 XNOR Outputs D2b Q2 F OR Output F NOR Output D3a Q3 D3b Q3 D4a Q4 D4b Q4 FUNCTION OUTPUTS F = (D0a ⊕ D0b) + (D1a ⊕ D1b) (D2a ⊕ D2b) + (D3a ⊕ D3b) + (D4a ⊕ D4b) 12/93 Motorola, Inc. 1996 2–1 REV 2 MC10E107 MC100E107 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic IIH Input HIGH Current IEE Power Supply Current 10E 100E min typ 25°C max min typ 200 85°C max min typ 200 max Unit 200 µA Condition mA 42 42 50 50 42 42 50 50 42 48 50 58 AC CHARACTERISTICS (VEE =VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic tPLH tPHL Propagation Delay to Output D to Q D to F tSKEW Within-Device Skew D to Q tr tf Rise/Fall Times 20 - 80% Q F 25°C 85°C min typ max min typ max min typ max 250 500 410 725 600 1000 250 500 410 725 600 100 250 500 410 725 600 1000 Unit Condition ps ps 75 75 75 1 ps 275 300 450 475 700 700 275 300 450 475 700 700 275 300 450 475 700 700 1. Within-device skew is defined as identical transitions on similar paths through a device. MOTOROLA 2–2 ECLinPS and ECLinPS Lite DL140 — Rev 4 MC10E107 MC100E107 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776–02 ISSUE D 0.007 (0.180) B Y BRK -N- T L –M M U 0.007 (0.180) X G1 M S N T L –M S S N S D Z -L- -M- D W 28 V 1 C A 0.007 (0.180) M R 0.007 (0.180) M T L –M S T L –M S N S N S H S N S 0.007 (0.180) M T L –M N S S 0.004 (0.100) G J -T- K SEATING PLANE F VIEW S G1 T L –M S N 0.007 (0.180) M T L –M S N S VIEW S S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). ECLinPS and ECLinPS Lite DL140 — Rev 4 T L –M K1 E S S VIEW D-D Z 0.010 (0.250) 0.010 (0.250) 2–3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 — 0.025 — 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 — 0.020 2° 10° 0.410 0.430 0.040 — MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 — 0.64 — 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 — 0.50 2° 10° 10.42 10.92 1.02 — MOTOROLA MC10E107 MC100E107 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–4 *MC10E107/D* MC10E107/D ECLinPS and ECLinPS Lite DL140 — Rev 4